Ice IE410 Programmierhandbuch

Operator & Parts Manual

Self_Contained Extractor

www.icecompanies.com

6210149U

REV.05(11-2016)

iE410

INTERNATIONAL CLEANING EQUIPMENT

SAFETY PRECAUTION. . . . . . . . . . . . . . . . . . . . . 2

MACHINE SET-UP. . . . . . . . . . . . . . . . . . . . . .3

MACHINE OPERATION. . . . . . . . . . . . . . . . . . . .3-4

MACHINE MAINTENANCE & STORAGE . . . . . . . . . . . . . . . . . . . .5

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . .6

MACHINE COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-19

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

WEAR & TEAR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

ICE iE410 1

TABLE OF CONTENTS

SAFETY PRECAUTION

2ICE iE410

OPERATOR

Carefully read and understand this manual before operating this machine.

This machine must be grounded!

This machine shall be grounded while in use to protect theoperator from electric shock.

Grounding provides a path of least resistance for electric current. This machine is equipped

with a cord having an equipment-grounding conductor and grounding plug. The plug must be

plugged into an appropriate outlet that is properly installed and grounded in accordance with all

local codes and ordinances. Do not remove the ground pin under any circumstances.

This machine is for use on a nominal 120-volt circuit

and has a grounding plug that resembles the plug

illustrated in Figure. Make sure that the machine is

connected to an outlet having the same conguration as

the plug. No adapter should be used with this machine.

This machine is intended for commercial use. It is constructed for use in an indoor environment

and is nor intended for any other use. Use only recommended accessories.

1. Do not operate machine:

– Unless trained and authorized. – Unless you have read and

– In ammable or explosive areas. understand the operators manual.

– With a damaged cord or plug – With the use of extension cords.

– If not in proper operating condition. – In outdoor areas and standing water.

2. Before operating machine:

– Make sure all safety devices are in place and operating properly.

3. When using machine:

– Do not run machine over cord. – Do not pull machine by cord or plug.

– Do not pull cord around – Do not unplug by pulling on the cord.

sharp edges or corners. – Do not stretch cord.

– Do not handle plug with wet hands. – Keep cord away from heated surfaces.

– Report machine damage or faulty

operation immediately.

To avoid electrical shock,please replace the power cord immediately if any damage is

being detected. The replacement must be performed only by an authorized person or

by our customer service center.

4. Before leaving or servicing machine:

– Turn off machine. – Unplug cord from outlet.

5. When servicing machine:

– Unplug cord from outlet. – Use manufacturer supplied or

approved replacement parts.

ICE iE410 3

OPERATOR

SELF-CONTAINED EXTRACTOR SET-UP

Carefully check the shipping carton for signs of damage. Report any carton damage to carrier

immediately.

Read operators manual thoroughly prior to operating or

servicing this machine!!!

Check carton contents to ensure carton is complete. Contact your ICE distributor if anything is

missing.

Contents:

- Carpet Extractor - 50’ extension power cable

Read operators manual thoroughly prior to operating or servicing

this machine!!!

1. Using a hose or bucket, ll tank with a maximum of 10 gallons of hot water.

2. Add distributor recommended cleaning solution.

Do not use flammable liquids or operate machine in or near

flammable liquids or vapors!!!

3. Connect the supplied extension power cable to the machine. Plug cord into a grounded wall

outlet. (see grounding instructions)

4. Drop the brush head to the oor with the foot release pedal on the back

of the machine.

MACHINE OPERATION

PRIOR TO EXTRACTING CARPETS

1. Inspect power cable and extension cable for damage. Replace cable if damage is found.

2. Vacuum carpet to remove debris prior to extracting carpet.

CARPET EXTRACTING

1. Turn on vacuum / pump switch.

NOTE: Solution will only spray when the brush / spray button is pushed.

2. To start cleaning, push the brush / spray button and begin to pull the machine backwards.

NOTE: For best cleaning results, pull back on the machine at a pace of approx. 10 feet in 15

seconds.

3. Release brush / spray button at the end of the path, and continue to pull machine back for

another 12 inches to pick up excess solution.

4. Tip machine back onto the transport wheels and push forward to begin next path.

5. During pickup, the oat shut-off will automatically prevent water from entering the

recovery tank once the recovery tank is full.

4 ICE iE410

OPERATOR

OPERATING HINTS

1. Overlap cleaning path by approx. 2 inches

2. Work away from power outlet and power cable in order to avoid damage to the power

cable.

3. Continually check for foam buildup in recovery tank. Use a distributor recommended foam

control solution.

NOTE: Excessive foam buildup will not activate the oat shut-off and may cause damage to

the vacuum motor.

4. Repeat extraction path on heavily soiled areas.

5. If brush stops spinning, there may be an obstruction in the brush. Unplug the power cable,

raise the brush off the oor and check for an obstruction. Check & reset the brush circuit

breaker located on the control housing.

6. When recover of the dirty solution ends, or the solution tank is empty, you must drain the

recovery tank. (see TANK DRAINING)

USE OF ACCESSORY TOOLS

NOTE: Prior to cleaning upholstery, be sure to read cleaning instructions provided by the

manufacturer.

1. Disconnect black vacuum hose off the back right side of the machine. Connect accessory

vacuum hose to area where the standard vacuum hose was removed.

2. Connect accessory solution hose to brass quick connect coupler located on the back of the

machine.

3. Connect accessory tool to solution and vacuum hoses.

4. Turn on vacuum / pump switch.

5. Operate accessory tools as needed.

6. When cleaning is completed, relieve water pressure from solution lines by turning off

vacuum / pump switch and then squeeze trigger for 4 seconds.

DRAINING TANKS

DRAINING SOLUTION TANK

1. To drain any remaining water from the solution tank,pull the solution tank level hose off the

hose tting.

2. Drain dirty solution into oor drain.

3. Reattach the hose to the hose tting.

DRAINING RECOVERY TANK

1. Turn off machine, unplug and remove power cable.

2. Unhook drain hose off the back of the machine and remove drain hose stopper.

3. Drain dirty solution into oor drain.

4. Replace drain hose stopper and reattach hose to back of machine.

NOTE: If foam develops in the recovery tank during vacuuming, use de-foamer chemical to

help eliminate the foam. Foam will not activate the float shut-off, and therefore, may cause

vacuum motor damage.

ICE iE410 5

OPERATOR

MACHINE MAINTENANCE

To keep the machine performing well for many years, please follow the following maintenance

procedures.

Always conrm that the machine is unplugged prior to performing any maintenance or

repairs!!!

DAILY MAINTENANCE

1. When cleaning operation is complete for the day, drain and rinse the recovery tank

thoroughly with clean water.

2. Remove remaining solution from solution tank.

3. Remove oat shut-off (ping pong ball in cage) from recovery tank and clean with water.

4. Remove and inspect spray jets. If necessary, clean jets in acetic acid solution.

Do not clean brass jets with a pointed object, as it will damage the jets.

5. Check brush assembly & remove any debris or carpet bers.

6. Check pick up head and remove any debris or carpet bers.

7. Check condition of the stainless steel pickup shoes on the pickup head. The shoes must

contact the oor for the whole length of the pickup head. Replace as necessary.

8. Clean machine with a nonabrasive cleaner.

9. Inspect power cable for any damage. Replace if necessary.

MONTHLY MAINTENANCE

1. Flush pump & plumbing with an acetic acid solution to dissolve any chemical buildup.

Mixing Instructions:

a) Premix 16 oz. or an acetic acid solution with 2 gallons of water and pour into solution tank.

b) Turn vacuum / pump switch on

c) Put machine head over oor drain and operate machine for 50 seconds.

d) Shut machine down and allow remaining solution to sit in machine overnight.

e) The following day, spray out remaining solution and ush system again with 3 gallons of

clean water.

2) Inspect machine for water leaks.

3) Lubricate wheels with a water resistance lubricant.

MACHINE STORAGE

1. Prior to storing the machine, ensure the solution and recovery tanks are clean and empty

of any solution.

2. Store machine in upright position in a dry area, with the brush head off the oor.

3. Remove recovery tank clear lid to allow for air circulation.

If you are storing the machine in an area which can freeze, be sure both tanks and

the solution plumbing are empty of all water and dry!

6 ICE iE410

OPERATOR

BASIC TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

Machine doesn't

work

Not plugged in to power source Plug into a grounded outlet

Faulty power cable Contact ICE Distributor

Faulty extension power cable Replace with new extension

power cable

Building circuit breaker tripped Reset circuit breaker

Solution pump not

working

Vacuum / pump switch not on Turn on switch

Vacuum / pump switch faulty Contact ICE Distributor

Faulty solenoid Contact ICE Distributor

Faulty solution pump Contact ICE Distributor

Pump overheated Determine cause and allow 30

minutes for pump to cool

Loose or broken wiring Contact ICE Distributor

Vacuum motor not

working

Vacuum / pump switch not on Turn on switch

Vacuum / pump switch faulty Contact ICE Distributor

Vacuum motor thermal overload

tripped

Check for obstruction and allow

30 minutes to cool

Faulty vacuum motor Contact ICE Distributor

Worn carbon brushes Contact ICE Distributor

Loose or broken wiring Contact ICE Distributor

Poor pick up Air leaking around clear recovery

lid

Ensure recovery lid is firmly

tightened

Clogged oat shut-off Remove float shut-off and clean

off debris

Float shut-off is activated Drain recovery tank

Loose drain hose stopper Ensure stopper is securely in

place

Loose vacuum hose connections Ensure vacuum hose connections

are tight

Defective vacuum hose Replace vacuum hose

Loose vacuum hose cuffs Ensure cuffs are secure to the

hose

Damaged or loose pickup head

shoes

Contact ICE Distributor

Pulling machine too fast Slow down cleaning operation

Uneven or no

solution spray

Solution tank is empty or low Fill solution tank

Vacuum / pump switch not on Turn on switch

Dirty or plugged spray tips Clean or replace spray tips

Improper spray tip size or spray

angle

Contact ICE Distributor

Worn spray tips Contact ICE Distributor

Faulty solution pump Contact ICE Distributor

Plugged solution tank lter Clean or replace lter

Pinched or kinked solution hose Check for obstructions and kinks

and reroute or replace if needed

MACHINE COMPONENTS

ICE iE410 7

OPERATOR

1. Vacuum/Pump ON/OFF switch 2. Brush circuit breaker

3. Brush/spray ON/OFF switch 4. Drain hose

5. Accessory tool solution hookup

6. Brush raise and lower foot pedal

7. Spray jets 8. Brush assembly

9. Pickup head 10. Solution tank ll port

11. Clear dome

8 ICE iE410

OPERATOR

ICE iE410 9

OPERATOR

PARTS LIST

DIA

PART

NUMBER DESCRIPTION NO

REQ'D

1 2320216 Clear Dome 1

2 2320218 Gasket,Clear Dome 1

3 2320217 Rubber Hinge 1

4 1421409 Washer,Plain,Φ4.3XΦ9X0.8 4

5 1321210 Screw, Ph, St4 X10 4

6 1221410 Screw, Ph, M4 X10 2

7 6210109 Bend, Tube 1

8 6210104 Coupler 1

9 6210103 Gasket,Coupler 1

10 6210108 Elbow 1

11 6210114 Coupler,Vac Hose 1

12 2230131 Plug, Serial number:000000-001234 1

13 6210705 Drain Hose, Serial number:000000-001234 1

8011030 Drain Hose,Serial number:001235- 1

14 6210113 Vac Hose 1

15 1962050 Clamp, Hose 2" 1

16 1021610 Screw, Hex, M6X10,SST 1

17 1422616 Washer, Lock, SST, Ø6 1

18 1421617 Washer, Plain, Φ6XΦ16X2 1

19 6150712 Clamp, Cord 1

20 6210503 Rocker Switch 1

21 6210502 Push Button Switch 1

22 6210504 Circuit Breaker, 2A 1

23 1221512 Screw, M5X12, PH 3

24 6210111 Clamp, Drain Hose 1

25 6210125 Warning Decal 1

26 6210501 Switch Housing 1

27 4020310 Strain Relief 1

28 6210518 Power Cord 1

29 6210505 Elbow Corrugated Tubing Fitting 1

30 6210506 Corrugated Tubing 1

31 6210136 Barb, Right Angle 1

32 6210135 Tubing 1

33 6180163 Barb, Hose 1

34 6180126 Nut, Coupling 1

35 6120667 Washer, Lock, Internal Toooth 1

36 6160509 Gasket, Solution, Intake 2

37 6120276 Washer, Plain 1

38 6180125 Coupling 1

39 6110411 Strainer, Line 1

Inhaltsverzeichnis

Andere Ice Bodenreinigungsmaschine Handbücher

Ice

Ice I18B Programmierhandbuch

Ice

Ice IP17 Programmierhandbuch

Ice

Ice RS26 Programmierhandbuch

Ice

Ice RS26L+ Programmierhandbuch

Ice

Ice IP17 Programmierhandbuch

Ice

Ice IB2000 Programmierhandbuch

Ice

Ice i28BTL Programmierhandbuch

Ice

Ice SCRUB 35D Bedienungsanleitung

Ice

Ice iS1100 Programmierhandbuch

Ice

Ice i36BT Programmierhandbuch

Ice

Ice i28BT Programmierhandbuch

Ice

Ice i20NBL Programmierhandbuch

Ice

Ice i20B Programmierhandbuch

Ice

Ice IB1500 Programmierhandbuch

Ice

Ice I18B Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch

Ice iE410 Programmierhandbuch

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken