Icom IC-7300 Installationsanleitung

BASIC MANUAL

i7300

HF/50 MHz TRANSCEIVER

Thank you for choosing this Icom product. The IC-7300 HF/50 MHz TRANSCEIVER is designed and built with Icom’s

state of the art technology and craftsmanship. With proper care, this product should provide you with years of

trouble-free operation. We appreciate you making the IC-7300 your transceiver of choice, and hope you agree

with Icom’s philosophy of “technology rst.” Many hours of research and development went into the design of

your IC-7300.

FEATURES

•RF Direct Sampling System

The IC-7300 employs an RF direct sampling system.

RF signals are directly converted to digital data and

processed in the FPGA. This system is a leading

technology marking an epoch in amateur radio.

•Real-Time Spectrum Scope

The spectrum scope is class-leading in resolution,

sweep speed and dynamic range. When you touch the

scope screen on the intended signal, the touched area is

magnied. The large 4.3 inch color TFT touch LCD offers

intuitive operation.

•New “IP+” Function

The new IP Plus function improves 3rd order intercept

point (IP3) performance. When a weak signal is received

adjacent to strong interference, the AD converter is

optimized against signal distortion.

•Class Leading RMDR and Phase Noise

Characteristics

The RMDR is improved to about 97dB (typical value) and

Phase Noise characteristics are also improved about

15dB (at 1 kHz frequency separation) compared to the

IC-7200.

•A 4.3 inch touch panel color display

•A built-in automatic antenna tuner

•Multi-function control for easy settings

SUPPLIED ACCESSORIES

L Different types of accessories may be supplied, or may

not be supplied depending on the transceiver version.

WORD DEFINITION

RDANGER! Personal death, serious injury or an

explosion may occur.

RWARNING! Personal injury, ﬁre hazard or electric

shock may occur.

CAUTION Equipment damage may occur.

NOTE

Recommended for optimum use. No

risk of personal injury, ﬁre or electric

shock.

EXPLICIT DEFINITIONS

IMPORTANT

READ ALL INSTRUCTIONS carefully completely

before using the transceiver.

SAVE THIS INSTRUCTION MANUAL— This

instruction manual contains full operating instructions

for the IC-7300

Hand microphone

(HM-219)

DC power cable*

(3 m: 9.8 ft)

Spare fuse

(25 A)

Spare fuse

(30 A)

Spare fuse

(5 A)

Speaker plug

(3.5 mm: 1/8" Stereo)

CW key plug

(6.35 mm: 1/4" Stereo)

ACC plug

(13 pin)

This product includes RTOS “RTX” software, and is

licensed according to the software license.

This product includes “zlib” open source software,

and is licensed according to the open source

software license.

This product includes “libpng” open source software,

and is licensed according to the open source

software license.

Refer to the Text les in the License folder of

included CD for information on the open source

software being used by this product.

*For European versions

•FOR CLASS B UNINTENTIONAL RADIATORS:

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

DISPOSAL

The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in

the European Union, all electrical and electronic products, batteries, and accumulators

(rechargeable batteries) must be taken to designated collection locations at the end of their work-

ing life. Do not dispose of these products as unsorted municipal waste.

Dispose of them according to the laws in your area.

FCC INFORMATION

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

WARNING: MODIFICATION OF THIS DEVICE

TO RECEIVE CELLULAR RADIOTELEPHONE

SERVICE SIGNALS IS PROHIBITED UNDER FCC

RULES AND FEDERAL LAW.

CAUTION: Changes or modications to this device,

not expressly approved by Icom Inc., could void

your authority to operate this device under FCC

regulations.

Icom is not responsible for the destruction or damage to the Icom transceiver, if the malfunction is because of:

• Force majeure, including, but not limited to, res, earthquakes, storms, oods, lightnings, or other natural

disasters, disturbances, riots, war, or radioactive contamination.

• The use of Icom transceiver with any equipment that is not manufactured or approved by Icom.

TRADEMARKS

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the

United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand and/or other countries.

Microsoft, Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and/or other

countries.

Adobe and Adobe Reader are registered trademark of Adobe Systems Incorporated.

All other products or brands are registered trademarks or trademarks of their respective holders.

iii

DTouch operation

In the Full manual or Basic manual, the touch

operation is described as shown below.

Touch

If the display is touched briey, one short beep

sounds.

Touch for 1 second

If the display is touched for 1 second, one

short and one long beep sound.

DTouch screen precautions

• The touch screen may not properly work when the

LCD protection lm or sheet is attached.

• Touching the screen with your nger nails, sharp

topped object and so on, or touching the screen

hard may damage it.

• Tablet PC’s operations such as ick, pinch in and

pinch out cannot be performed on this touch screen.

DTouch screen maintenance

• If the touch screen becomes dusty or dirty, wipe it

clean with a soft, dry cloth.

• When you wipe the touch screen, be careful not to

push it too hard or scratch it with your nger nails.

Otherwise you may damage the screen.

The following items are included on the CD.

•Full manual (English)

Instructions for full operations, the same as this

manual.

•Basic manual (English)

Instructions for basic operations, the same the

manual supplied with the transceiver.

•Basic manual

(German, Spanish, French, Italian, and other)

Instructions for basic operations in German,

Spanish, French, Italian, and other languages.

This manual may not be included, depending on the

transceiver version.

•Schematic diagram

Includes the schematic and block diagrams.

•HAM radio Terms

A glossary of HAM radio terms.

•Adobe®Reader®Installer

Installer for Adobe®Reader®.

A PC with the following Operating System is required.

• Microsoft®Windows®10

• Microsoft®Windows® 8.1

• Microsoft®Windows® 7

• Microsoft®Windows Vista®

To read the manuals or Schematic diagram, Adobe®

Reader® is required. If you have not installed it,

please install the Adobe®Reader® on the CD or

download it from Adobe Systems Incorporated’s

website.

Starting the CD

1. Insert the CD into the CD drive.

2. Double click “Menu.exe” on the CD.

• Depending on the PC setting, the menu screen shown

below is automatically displayed.

3. Click the desired button to open the file.

LTo close the Menu screen, click [Quit].

Closes the Menu screenInstalls the Adobe®Reader®

Opens the

Full manual

Opens the

Schematic

diagram

Opens the

Glossary

ABOUT THE TOUCH SCREEN

ABOUT THE SUPPLIED CD

Opens the English

Basic manual

(this manual)

Opens the multi-

language Basic manual

L Different types of menu screen may be displayed,

depending on the transceiver version.

ABOUT THE INSTRUCTIONS

Instruction example

» SET > Display > Display Type

Detailed instruction

1. Push

Push

• Opens the MENU screen.

2. Touch [SET].

MENU screen

• Opens the SET screen.

3. Rotate

MULTI

, and then push

MULTI

to select

“Display.”

Rotate

Push

4. Rotate

MULTI

, and then push

MULTI

to select

“Display Type.”

SET screen

Rotate

Push

The Full and Basic manuals are described based on

the following manner.

“ ” (Quotation marks):

Used to indicate icons, setting items, and screen*

titles displayed on the screen.

[ ] (brackets):

Used to indicate keys.

* The screen titles are also indicated in uppercase letters.

(Example: FUNCTION screen)

Routes to the set modes and setting screens

Routes to the set mode, setting screen and the setting

items are described in the following manner.

DISPLAY screen

“Display Type” screen

TABLE OF CONTENTS

IMPORTANT............................................................... i

FEATURES................................................................. i

EXPLICIT DEFINITIONS............................................ i

SUPPLIED ACCESSORIES ....................................... i

FCC INFORMATION ..................................................ii

TRADEMARKS...........................................................ii

DISPOSAL..................................................................ii

ABOUT THE TOUCH SCREEN ................................iii

DTouch operation...................................................iii

DTouch screen precautions ...................................iii

DTouch screen maintenance .................................iii

ABOUT THE SUPPLIED CD .....................................iii

ABOUT THE INSTRUCTIONS ..................................iv

PRECAUTIONS........................................................vii

1 PANEL DESCRIPTION .................................... 1-1

Front panel ....................................................... 1-1

Rear panel........................................................ 1-3

Touch panel display.......................................... 1-4

DMulti-function menus.................................. 1-6

DMENU screen ............................................ 1-6

DFUNCTION screen .................................... 1-6

DQUICK MENU............................................ 1-6

Keyboard entering and editing ......................... 1-7

DEntering and editing characters ................. 1-7

DKeyboard types.......................................... 1-7

DEntering and editing................................... 1-7

DEntering and editing example .................... 1-8

2 INSTALLATION AND CONNECTIONS ........... 2-1

Selecting a location .......................................... 2-1

Front panel connection..................................... 2-1

Heat dissipation................................................ 2-1

Grounding......................................................... 2-1

Rear panel connection ..................................... 2-2

Connecting an external DC power supply ....... 2-3

Connecting the antenna tuner .......................... 2-3

3 BASIC OPERATION ........................................ 3-1

When rst applying power ................................ 3-1

Turning power ON or OFF................................ 3-1

Adjusting the volume level................................ 3-1

About the VFO and Memory modes................. 3-1

Using the VFO mode........................................ 3-1

DSelecting the VFO A or VFO B................... 3-1

DEqualizing VFO A and VFO B .................... 3-1

Selecting the operating band............................ 3-2

DUsing the band stacking registers.............. 3-2

Selecting the operating mode........................... 3-2

Setting the frequency ....................................... 3-3

DUsing the Main Dial.................................... 3-3

DAbout the Tuning Step function.................. 3-3

DChanging the Tuning Step ......................... 3-3

DAbout the 1 Hz step Fine Tuning function.. 3-3

DAbout the 1/4 Tuning function .................... 3-4

DAbout the Auto Tuning Step function ......... 3-4

DDirectly entering a frequency ..................... 3-4

DBand Edge Beep........................................ 3-5

DEntering a Band Edge................................ 3-6

RF gain and SQL level ..................................... 3-9

Dial Lock function ............................................. 3-9

Basic transmission ........................................... 3-9

Adjusting the transmit output power ................. 3-9

DAdjusting the transmit output power .......... 3-9

Meter display .................................................. 3-10

DMeter display selection ............................ 3-10

DMulti-function meter ................................. 3-10

Adjusting the microphone gain ....................... 3-10

About the 5 MHz frequency band operation

(USA version only).......................................... 3-11

4 RECEIVING AND TRANSMITTING................. 4-1

Preampliers .................................................... 4-1

Attenuator......................................................... 4-1

RIT function ...................................................... 4-1

DRIT monitor function .................................. 4-1

AGC function control ........................................ 4-2

DSelecting the AGC time constant

preset value ............................................... 4-2

DSetting the AGC time constant................... 4-2

Using the Twin PBT.......................................... 4-3

Selecting the IF lter......................................... 4-4

Selecting the IF lter shape.............................. 4-4

IP Plus function ................................................ 4-5

Noise Blanker ................................................... 4-5

DAdjusting the NB level and time................. 4-5

Noise Reduction ............................................... 4-6

DAdjusting the Noise Reduction level .......... 4-6

Notch Filter ....................................................... 4-6

DAuto Notch function ................................... 4-6

DManual Notch function ............................... 4-6

VOX function .................................................... 4-7

DAdjusting the VOX function........................ 4-7

DTurning ON the VOX function .................... 4-7

∂TX function..................................................... 4-8

D∂TX monitor function................................. 4-8

Monitor function................................................ 4-8

Setting the Speech Compressor ...................... 4-9

Split frequency operation................................ 4-10

DUsing the Quick Split function.................. 4-10

DUsing the receive and transmit

frequencies set to VFO A and VFO B.......4-10

Split Lock function .......................................... 4-11

Setting the transmit lter width ....................... 4-11

Operating CW................................................. 4-11

DSetting the CW pitch control .................... 4-11

DSetting the key speed .............................. 4-12

DAbout the Break-in function ..................... 4-12

DCW Auto Tuning function ......................... 4-13

DAbout the CW Reverse mode .................. 4-13

DElectronic Keyer function ......................... 4-14

DMonitoring the CW side tone ................... 4-14

TABLE OF CONTENTS (Continued)

4 RECEIVING AND TRANSMITTING (Continued)

Operating RTTY (FSK)................................... 4-15

DAbout the RTTY reverse mode ................ 4-15

DTwin Peak Filter ....................................... 4-15

DFunctions on the RTTY DECODE screen

... 4-16

DSetting the decoder threshold level ......... 4-16

FM repeater operation.................................... 4-17

DSetting the repeater tone frequency ........ 4-17

5 SCOPE OPERATION....................................... 5-1

Spectrum scope screen.................................... 5-1

DUsing the Spectrum Scope ........................ 5-1

DCenter mode .............................................. 5-2

DFixed mode ................................................ 5-2

DMarker........................................................ 5-2

DTouch screen operation ............................. 5-3

DMini scope screen...................................... 5-3

Audio scope screen.......................................... 5-3

6 USING AN SD CARD....................................... 6-1

About the SD card ............................................ 6-1

Saving data onto the SD card .......................... 6-1

Inserting or removing the SD card.................... 6-1

DInserting ..................................................... 6-1

DRemoving................................................... 6-1

Unmounting an SD card ................................... 6-2

Formatting an SD card ..................................... 6-2

7 ANTENNA TUNER OPERATION .................... 7-1

About the internal antenna tuner ...................... 7-1

Internal antenna tuner operation ...................... 7-1

DManual tuning ............................................ 7-1

DPTT Tuner start.......................................... 7-1

8 SET MODE....................................................... 8-1

Set mode description........................................ 8-1

DEntering the Set mode ............................... 8-1

Tone Control ..................................................... 8-2

Function............................................................ 8-3

Connectors ....................................................... 8-5

Display.............................................................. 8-6

Time Set ........................................................... 8-7

SD Card............................................................ 8-7

Others............................................................... 8-7

9 MAINTENANCE............................................... 9-1

Resetting .......................................................... 9-1

DPartial reset................................................ 9-1

DAll reset...................................................... 9-1

10 SPECIFICATIONS ......................................... 10-1

DGeneral .................................................... 10-1

DTransmitter............................................... 10-1

DReceiver................................................... 10-2

DAntenna tuner .......................................... 10-2

11 OPTIONS ....................................................... 11-1

Options ........................................................... 11-1

Mounting the MB-118 ..................................... 11-2

12 CONNECTOR INFORMATION ...................... 12-1

ACC socket .................................................... 12-1

DOPC-599 ACC conversion cable pin

assignments............................................. 12-2

Microphone connector.................................... 12-2

DExternal keypad ....................................... 12-2

KEY jack......................................................... 12-3

EXT-SP jack ................................................... 12-3

REMOTE jack................................................. 12-3

ALC jack ......................................................... 12-3

SEND jack ...................................................... 12-3

PHONES jack................................................. 12-3

DC power socket ............................................ 12-3

INDEX......................................................................... I

ABOUT CE............................................................... III

INSTALLATION NOTES ..................................... III

vii

PRECAUTIONS

RDANGER HIGH RF VOLTAGE! NEVER touch an

antenna or antenna connector while transmitting. This could

cause an electrical shock or burn.

RDANGER! NEVER operate the transceiver near

unshielded electrical blasting caps or in an explosive

atmosphere. This could cause an explosion and death.

RWARNING RF EXPOSURE! This device emits Radio

Frequency (RF) energy. Extreme caution should be

observed when operating this device. If you have any

questions regarding RF exposure and safety standards

please refer to the Federal Communications Commission

Ofce of Engineering and Technology’s report on

Evaluating Compliance with FCC Guidelines for Human

Radio Frequency Electromagnetic Fields (OET Bulletin 65).

RWARNING! NEVER operate the transceiver with a

headset or other audio accessories at high volume levels. If

you experience a ringing in your ears,reduce the volume or

discontinue use.

RWARNING! NEVER apply AC power to the [DC13.8V]

socket on the transceiver rear panel. This could cause a re

or damage the transceiver.

RWARNING! NEVER apply more than 16 V DC to the

[DC13.8V] socket on the transceiver rear panel. This could

cause a re or damage the transceiver.

RWARNING! NEVER reverse the DC power cable

polarity. This could cause a re or damage the transceiver.

RWARNING! NEVER remove the fuse holder on the DC

power cable. Excessive current caused by a short could

cause a re or damage the transceiver.

RWARNING! NEVER let metal, wire or other objects

contact the inside of the transceiver, or make incorrect

contact with connectors on the rear panel. This could cause

an electric shock or damage the transceiver.

RWARNING! NEVER operate or touch the transceiver

with wet hands. This could cause an electric shock or

damage to the transceiver.

RWARNING! Immediately turn OFF the transceiver power

and remove the DC power cable from the transceiver if it

emits an abnormal odor, sound or smoke. Contact your

Icom dealer or distributor for advice.

RWARNING! NEVER put the transceiver on an unstable

place where the transceiver may suddenly move or fall.

This could cause an injury or damage the transceiver.

RWARNING! NEVER operate the transceiver during a

lightning storm. It may result in an electric shock, cause

a re or damage the transceiver. Always disconnect the

power souce and antenna before a storm.

CAUTION: NEVER expose the transceiver to rain, snow or

any liquids.

CAUTION: NEVER change the internal settings of the

transceiver. This could reduce transceiver performance

and/or damage to the transceiver. The transceiver warranty

does not cover any problems caused by unauthorized

internal adjustments.

CAUTION: NEVER install or place the transceiver in a

place without adequate ventilation, or block any cooling

vents on the top, rear, sides or bottom of the transceiver.

Heat dissipation may be reduced and damage the

transceiver.

CAUTION: NEVER use harsh solvents such as Benzine or

alcohol when cleaning, as they will damage the transceiver

surfaces.

CAUTION: NEVER leave the transceiver in areas with

temperatures below –10°C (+14°F) or above +60°C

(+140°F) for mobile operations.

CAUTION: NEVER place the transceiver in excessively

dusty environments. This could damage the transceiver.

DO NOT place the transceiver against walls or putting

anything on top of the transceiver. This may overheat the

transceiver.

BE CAREFUL! The Main unit will become hot when

operating the transceiver continuously for long periods of

time.

CAUTION: If you use a linear amplier, set the

transceiver’s RF output power to less than the linear

amplier’s maximum input level, otherwise a high input

could damage the linear amplier.

CAUTION: Use only Icom supplied or optional

microphones. Other manufacturer’s microphones may have

different pin assignments, and could damage the connector

and/or the transceiver.

NEVER leave the transceiver in an insecure place to avoid

use by unauthorized persons.

Turn OFF the transceiver’s power and/or disconnect the AC

power cable when you will not use the transceiver for a long

period of time.

Turn OFF the transceiver’s power and/or disconnect the DC

power cable when you will not use the transceiver for long

period of time.

The LCD display may have cosmetic imperfections

that appear as small dark or light spots. This is not a

malfunction or defect, but a normal characteristic of LCD

displays.

PANEL DESCRIPTION

1-1

Front panel

qPOWER KEY

POWER

(p. 3-1)

Turns the transceiver ON or OFF.

wTRANSMIT KEY

TRANSMIT

(p. 3-9)

Toggles between transmit and receive.

eANTENNA TUNER KEY

TUNER

(p. 7-1)

Turns the antenna tuner ON or OFF, or activates

the tuner.

rVOX/BREAK-IN KEY

VOX/BK-IN

Turns the VOX function (p. 4-7) and Break-in

function (p. 4-12) ON or OFF.

tHEADPHONE JACK [PHONES] (p. 2-1)

Connects to a standard stereo headphones.

yMICROPHONE CONNECTOR [MIC] (p. 2-1)

Connects to the supplied or an optional microphone.

uVOLUME CONTROL

AF RF/SQL

(p. 3-1)

Adjusts the audio output level.

iSD CARD SLOT [SD CARD] (p. 6-1)

Accepts an SD card.

oRF GAIN CONTROL/SQUELCH CONTROL

AF RF/SQL

(p. 3-9)

Adjusts the RF gain and squelch threshold levels.

!0 MENU KEY

(p. 1-6)

Opens the MENU screen.

i !0 !1 !2 !3 !4 !6 !7u o !8!5

!1 FUNCTION KEY

FUNCTION

(p. 1-6)

Displays the FUNCTION screen.

!2 MINI SCOPE KEY

M.SCOPE

(p. 5-1)

Displays the Mini Scope or Spectrum Scope.

!3 QUICK KEY

QUICK

(p. 1-6)

Displays the QUICK MENU.

!4 EXIT KEY

EXIT

(p. 1-6)

Exits a setting screen or returns to the previous

screen.

!5 AUTO TUNE KEY

AUTO

TUNE

(p. 4-13)

Automatically tunes the operating frequency to a

received CW signal.

!6 SPEECH/LOCK KEY

SPEECH

(p. 3-9)

Announces the operating frequency or receiving

mode, or electronically locks

MAIN DIAL

!7 TENSION ADJUSTER

Adjusts the friction of

MAIN DIAL

!8 MAIN DIAL

MAIN DIAL

(p. 3-3)

Changes the operating frequency.

!9 MEMORY CHANNEL UP/DOWN KEY

▲

▼

Changes the Memory channel.

This section describes the keys, controls and dials that you use to operate the IC-7300.

Refer to the pages posted beside each key, control, or dial for details.

1PANEL DESCRIPTION

1-2

Front panel (Continued)

#3#4 @8@9 @3

#1 #0 @5@7 @4

@0 MEMO PAD KEY

MPAD

Sequentially calls up the contents in the Memo

Pads, or saves the displayed contents into the

Memo Pad.

@1 VFO/MEMORY KEY

V/M

(p. 3-1)

Switches between the VFO and Memory mode, or

copies the memory channel contents to the VFO.

@2 CLEAR KEY

CLEAR

Clears the RIT or TX shift frequency.

@3 A/B KEY

A/B

(p. 3-1)

Switches between VFO A and VFO B, or sets the

selected VFO’s frequency to the other VFO.

@4 TX KEY

(p. 4-8)

Turns the TX function ON or OFF.

@5 RIT KEY

RIT

(p. 4-1)

Turns the Receiver Incremental Tuning (RIT)

function ON or OFF.

@6 SPLIT KEY

SPLIT

(p. 4-10)

Turns the Split function ON or OFF.

@7 MULTI-FUNCTION CONTROL

MULTI

(p. 1-6)

Displays the Multi-function menu for various

adjustments, or selects a desired item.

@8 TRANSMIT FREQUENCY CHECK KEY

XFC

(p. 4-8)

Enables you to monitor the transmit frequency while

holding it down in the Split mode.

@9 TX/RX INDICATOR (p. 3-9)

Lights red while transmitting and lights green while

receiving.

#0 NOISE REDUCTION KEY

(p. 4-6)

Turns the Noise Reduction function ON or OFF.

#1 NOTCH KEY

NOTCH

(p. 4-6)

 TurnstheNotchlterONorOFF.

TWIN PASSBAND TUNING CONTROL

TWIN PBT

CLR

(p. 4-3)

 AdjuststheIFlter’spassbandwidth.

#3 PREAMP/ATTENUATOR KEY

P.AMP AT T

(p. 4-1)

Turns ON or OFF, and selects one of two receive

RFpreampliersorturnstheAttenuatorONorOFF.

#4 NOISE BLANKER KEY

(p. 4-5)

Turns the Noise Blanker ON or OFF.

Andere Handbücher für IC-7300

Inhaltsverzeichnis

Andere Icom Transceiver Handbücher

Icom

Icom IC-M603 Bedienungsanleitung

Icom

Icom IC-706MKIIG Bedienungsanleitung

Icom

Icom IC-91AD Bedienungsanleitung

Icom

Icom IC-7600 Bedienungsanleitung

Icom

Icom iDAS IC-F3102D Bedienungsanleitung

Icom

Icom IC-47A Bedienungsanleitung

Icom

Icom IC-V82 Bedienungsanleitung

Icom

Icom IC-375A Bedienungsanleitung

Icom

Icom ic-f5021 Bedienungsanleitung

Icom

Icom IC-F7000 Bedienungsanleitung

Icom

Icom IF3061S Bedienungsanleitung

Icom

Icom IC-E208 Bedienungsanleitung

Icom

Icom M802 Bedienungsanleitung

Icom

Icom IC-22U Bedienungsanleitung

Icom

Icom IC-F4022T Bedienungsanleitung

Icom

Icom VHF MARINE TRANSCEIVER IC-M501EURO Bedienungsanleitung

Icom

Icom IC-746 Bedienungsanleitung

Icom

Icom IC-M502 Bedienungsanleitung

Icom

Icom IC-7800 Bedienungsanleitung

Icom

Icom IC-F11 Bedienungsanleitung

Icom

Icom IC-211 Bedienungsanleitung

Icom

Icom IC-7700 Bedienungsanleitung

Icom

Icom IC-3A Bedienungsanleitung

Icom

Icom IC-M330 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung