Icom IC-7300 Bedienungsanleitung
HF/50/70MHz Transceiver
Getting Started with the Icom
7300 Quick Guide
This is a brief set up document for the Icom 7300.
Serial No. 02023063
Purchase Date: 14 September 2019
Tri-City Amateur Radio Club
IC-7300 Kit Contents
Box – 1
IC-7300 Radio
Box – 2
MFJ -4230 MVP Power Supply and Power Cord
Daiwa CN-501H SWR Meter and 12 Volt power line
ICOM Hand Microphone
USB A/B cord
Ground jumper
PL-259 RF Jumper (Radio to SWR Meter)
IC-7300 NIFTY Manual
3
Front Continued
4
Rear
Connections on the IC-7300 Radio
Basic connections on the rear of the Radio (Rear Picture)
Earth Ground – Connect the ground wire to the Andersen power
pole connector and secure to a ground point
Connect the MFJ-4230 to a source of 115vac and verify that its
output is set to 13.8vdc. Turn off the Power supply and then connect
the IC-7300 power line to the connector on the radio and the
opposite end to the MFJ-4230.
Antenna Connection – Connect the 50 ohm feed line from the
antenna to the DAWI SWR Meter and connect the jumper cable from
the DAWI SWR meter to the Antenna connector on the rear of the
radio.
Once all connections are complete turn on the power supply and
press the “POWER” button on the IC-7300 for 1 second to turn on
the radio.
USB-B connector – to connect the radio to a PC use the USB A/B
cable and connect the B side to the radio and the A side to the PC.
A side
B side
Front Connections on the radio (Front Picture)
1. Connect the hand Mic to the “MIC” (6) connector.
Plug HF jumper into
Antenna connector on the
radio and the TR input on
the SWR meter
Plug Power Cord
into AC power
Plug power cable into Andersen
Power Pole connector on Power
Supply and into Radio power
connector after verifying you have
13.8 vdc on the power supply
Connect Antenna Feed
Line into the ANT
connector on the SWR
meter
Connect the SWR meter
power cord to the power
jack on the rear of the
SWR meter and to the
Andersen Power Pole
connector on the power
supply
IC-7300 Radio Kit
Connection Diagram
Connect the ground
lead to the
Andersen Power
Pole Connector on
the rear of the radio
and to ground.
Start up procedure for IC 7300 Radio
1. Once all connections are complete , turn on the power supply and
press the “Power” button (1) to turn on the radio.
2. Press the “Menu” button (10) and the Menu screen will appear.
3. Press the “Scope” icon to bring up the Waterfall display. Press the
“Return Key” icon [bottom right] to go to the waterfall display.
4. To change the operational Mode of the radio, HF or
Digital, press the “Menu” button and select the “SET” icon.
Use the arrow slider on the right to go to page 3 and tap on
the SD Card icon. Select the Digital or HF file and tap on the
line. Select “ALL” and tap again. The file loads and a box
pops up asking to cycle power to load the program. Select
“Yes”.
The radio will restart in the selected mode.
5. To select Power output for the radio press on the
Multi-Function Control (27) and a window will pop up
displaying Power, MIC GAIN, COMP & Monitor. Tap the
power are; it will backlite blue, and then turn the control
knob to select the desired power output level.
NOTE: You can adjust several settings on this radio for your
preference and save them to a unique file on the SD card.
Do not overwrite the 2 original files.
BAND Select and Tuning the IC-7300
1. To select the desired Band touch the Frequency readout on
the screen. A pop up window will open and you can tap on
the desired Band.
2. To change Frequency simply rotate the Main Dial (18).
3. To tune the radio press “Tuner” (3) and the internal tuner
will tune the antenna to the radio.
Frequency readout
Andere Handbücher für IC-7300
12
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Icom Transceiver Handbücher
Icom
Icom IC-2000 Bedienungsanleitung
Icom
Icom IC-F3001 Bedienungsanleitung
Icom
Icom VHF IC-F50 Montage- und Bedienungsanleitung
Icom
Icom iF3230D Series Bedienungsanleitung
Icom
Icom ID-1 Bedienungsanleitung
Icom
Icom IC-91A Bedienungsanleitung
Icom
Icom ID-51A Einrichtungshandbuch
Icom
Icom IC-E90 Bedienungsanleitung
Icom
Icom IC-A2 Bedienungsanleitung
Icom
Icom IC-V200T Bedienungsanleitung
Icom
Icom IC-F2000 series Bedienungsanleitung
Icom
Icom IC-7300 Betriebsanleitung
Icom
Icom IC-M34 Bedienungsanleitung
Icom
Icom IC-78 Bedienungsanleitung
Icom
Icom IC706MK2G Bedienungsanleitung
Icom
Icom IC-M87 Bedienungsanleitung
Icom
Icom IC-V8000 Bedienungsanleitung
Icom
Icom IC-3220A Bedienungsanleitung
Icom
Icom IC-M35 Bedienungsanleitung
Icom
Icom IC-735 Bedienungsanleitung
