Icom IC-F1710 Bedienungsanleitung

INSTRUCTION MANUAL

UHF MOBILE TRANSCEIVER

iF2810

iF2710

VHF MOBILE TRANSCEIVER

iF1810

iF1710

Above photo shows the IC-F1810 or IC-F2810.

IMPORTANT

READ ALL INSTRUCTIONS carefully and com-

pletely before using the transceiver.

SAVE THIS INSTRUCTION MANUAL — This

instruction manual contains important operating instructions

for the IC-F1710, IC-F1810, IC-F2710 and IC-F2810 VHF/

UHF MOBILE TRANSCEIVERS.

See the operating guide for details of MDC 1200 system

operation. Consult your Icom dealer or system operator

for details concerning your transceivers programming.

EXPLICIT DEFINITIONS

WORD DEFINITION

RWARNING Personal injury, fire hazard or electric

shock may occur.

CAUTION Equipment damage may occur.

NOTE

If disregarded, inconvenience only. No risk

of personal injury, ﬁre or electric shock.

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-

porated (Japan) in Japan, the United states, the United Kingdom, Germany,

France, Spain, Russia and/or other countries.

All other products or brands are registered trademarks or trademarks of their

respective holders.

PRECAUTIONS

RWARNING! NEVER connect the transceiver to an

AC outlet. This may pose a ﬁre hazard or result in an electric

shock.

RWARNING! NEVER connect the transceiver to a

power source of more than 16 V DC such as a 24 V battery.

This connection will ruin the transceiver.

RWARNING! NEVER cut the DC power cable be-

tween the DC plug and fuse holder. If an incorrect connection

is made after cutting, the transceiver might be damaged.

RWARNING! NEVER place the transceiver where

normal operation of the vehicle may be hindered or where it

could cause bodily injury.

CAUTION! NEVER allow children to touch the trans-

ceiver.

CAUTION! NEVER expose the transceiver to rain,

snow or any liquids.

USE the speciﬁed microphone only. Other microphones

have different pin assignments and may damage the trans-

ceiver.

DO NOT use or place the transceiver in areas with tem-

peratures below –25°C or above +55°C, or in areas subject to

direct sunlight, such as the dashboard.

DO NOT operate the transceiver without running the ve-

hicle’s engine. The vehicle’s battery will quickly run out if the

transceiver transmits while the vehicle’s engine OFF.

DO NOT place the transceiver in excessively dusty envi-

ronments.

DO NOT place the transceiver against walls. This will ob-

struct heat dissipation.

DO NOT use chemical agents such as benzine or alcohol

when cleaning, as they damage the transceiver surfaces.

BE CAREFUL! The transceiver will become hot when

operating continuously for long periods.

Approved Icom optional equipment is designed for optimal

performance when used with an Icom transceiver.

Icom is not responsible for the destruction or damage to an

Icom transceiver in the event the Icom transceiver is used

with equipment that is not manufactured or approved by

Icom.

iii

TABLE OF CONTENTS

IMPORTANT.......................................................................... i

EXPLICIT DEFINITIONS....................................................... i

PRECAUTIONS.................................................................... ii

TABLE OF CONTENTS....................................................... iii

1 PANEL DESCRIPTION................................................1–7

 n Front panel ...................................................................1

 n Function display ...........................................................2

 n Programmable function keys........................................3

2 BASIC OPERATION..................................................8–13

 nTurning power ON ........................................................8

 nChannel selection.........................................................8

 n Call procedure..............................................................9

 nReceiving and transmitting...........................................9

 nScrambler function .....................................................12

 nUser set mode............................................................13

3 BIIS OPERATION ....................................................14–24

 nDefault setting ............................................................14

 nReceiving a call ..........................................................14

 nTransmitting a call.......................................................16

 n Receiving a message.................................................18

 n Transmitting a status...................................................20

 n Transmitting an SDM (Short Data Message)..............21

 nPosition data transmission..........................................23

 nPrinter connection ......................................................23

 nDigital ANI ..................................................................23

 nAuto emergency transmission ....................................23

 nStun function ..............................................................24

 nBIIS indication ............................................................24

 nPriority A channel selection........................................24

 nHorn output ................................................................24

4 CONNECTION AND MAINTENANCE ....................25–29

 nRear panel connection ...............................................25

 nSupplied Accessories.................................................26

 nMounting the transceiver ............................................27

 nOptional UT-109 or UT-110 installation.......................27

 nOptional OPC-617 installation ....................................... 28

 n Antenna......................................................................29

 n Fuse replacement ......................................................29

 n Cleaning .....................................................................29

 n Options.......................................................................29

5 DOC .........................................................................30–31

I c o m I n c

qe*w

IC-F1710

F2710

IC-F1810

F2810

y ru t

nFront panel

qAF VOLUME CONTROL KNOB

Rotate the knob to adjust the audio output level.

• Minimum audio level is pre-programmed.

wFUNCTION DISPLAY (p. 2)

Displays a variety of information, such as an operating

channel number/name, 5-tone code, DTMF numbers and

audible condition, etc.

eDIAL or UP/DOWN KEYS

• IC-F1710, F2710: DIAL

Rotate to select an operating channel, etc.

• IC-F1810, F2810: UP/DOWN Keys

Push to select an operating channel, etc.

*The desired function can be assigned by your dealer. (p. 3)

r10-KEYPAD (IC-F1810 or IC-F2810 only)

The keypad allows you to enter digits to:

• Select memory channels, tone channels and DTMF codes (when

in the DTMF code channel selection mode)

• Set TX codes and BIIS status number

• Input text message for SDM operation

• Start up with a password

tBUSY INDICATOR

Lights green while receiving a signal, or when the squelch

is open.

PANEL DESCRIPTION

1PANEL DESCRIPTION

yPOWER SWITCH [POWER]

Push to turn the power ON and OFF.

• The following functions are available at power ON as options:

- Automatic scan start

- Password prompt

- Set mode

uTRANSMIT INDICATOR

Lights red while transmitting.

iDEALER-PROGRAMMABLE KEYS

 

Desired functions can be programmed independently by

your dealer. (p. 3)

In this instruction manual, these keys are from the left,

called [P0]/[P1]/[P2]/[P3]/[P4].

oMICROPHONE CONNECTOR

 

Connect the supplied microphone or optional DTMF micro-

phone.

NEVER connect non-speciﬁed microphones. The pin

assignments may be different and the transceiver may

be damaged.

ï MICROPHONE

The supplied or optional microphone has a PTT switch and

a hanger hook.

• The following functions are available when the microphone is on or

off hook:

- Automatic scan start when on hook.

- Automatic priority channel selection when off hook.

- Sets to ‘Inaudible’ condition (mute condition) when on hook.

- Sets to ‘Audible’ condition (unmute condition) when off hook.

nFunction display

1 3 6 . 1 N a r

q w e r t y u i o

qSIGNAL STRENGTH INDICATOR

Indicates relative signal strength level.

wLOW POWER INDICATOR

Appears when low output power is selected.

eAUDIBLE INDICATOR

 ➥ Appears when the channel is in the ‘audible’ (unmute)

condition.

 ➥ Appears when the speciﬁed 5-tone/BIIS code is re-

ceived.

rCOMPANDER INDICATOR

Appears when the compander function is activated.

tSCRAMBLER INDICATOR

Appears when the voice scrambler function is activated.

PANEL DESCRIPTION

yBELL INDICATOR

 Appears/blinks when the speciﬁc 5-tone/BIIS code is re-

ceived, according to the pre-programming.

uCALL CODE MEMORY INDICATOR

Appears when the call code memory is selected.

iSDM MEMORY INDICATOR

Appears when the SDM memory is displayed.

oSDM INDICATOR

 Appears when an SDM is received, or a transmit SDM is

selected.

!0 ALPHANUMERIC DISPLAY

 

Displays an operating channel number, channel name, Set

mode contents, DTMF code, etc.

The indication mode can be selected from 1 line or 2 lines.

Ask your dealer for details.

In this instruction manual, the LCD illustration is described

using the 2 lines indication mode.

!1 ACTIVATED KEY INDICATOR

 Appears above the key assigned as [DIGITAL] key when

that key has been activated.

nProgrammable function keys

The following functions can be assigned to [DIAL]*, [UP],

[DOWN], [P0], [P1], [P2], [P3] and [P4] programmable func-

tion keys.

Consult your Icom dealer or system operator for details con-

cerning your transceivers programming.

If the programmable function names are bracketed in the fol-

lowing explanations, the speciﬁc key is used to activate the

function depends on the programming.

*The functions you can assign to [DIAL] are limited.

(Only functions marked with Ican be assigned.)

ICH UP AND DOWN KEYS

➥Push (or Rotate)* to select an operating channel.

➥Push (or Rotate)* to select a transmit code channel after

pushing [TX Code CH Select].

➥Push (or Rotate)* to select a DTMF channel after pushing

[DTMF Autodial].

➥Push (or Rotate)* to select a scan group after pushing and

holding [Scan A Start/Stop]/[Scan B Start/Stop].

➥Push (or Rotate)* to select a BIIS code, status number or

SDM after pushing [Digital].

*Rotate when this function is assigned to [DIAL].

IZONE UP AND DOWN KEY (This function is for [DIAL] only)

Rotate to select the desired zone.

1PANEL DESCRIPTION

ZONE KEY

Push this key, then select the desired zone using [CH Up]/

[CH Down].

What is “zone”?—The desired channels are assigned into

a zone according to the intended use for grouping.

For example, ‘Staff A’ and ‘Staff B’ are assigned into a

“Business” zone, and ‘John’ and ‘Cindy’ are assigned into a

“Private” zone.

SCAN A START/STOP KEY

➥This key’s operation depends on the Power ON Scan setting.

When the power ON scan function is turned OFF;

Push to start and cancel scanning operation. In case of

transmission during scan, cancels scanning.

When the power ON scan function is turned ON;

Push to pause scanning.Scanning resumes after a speciﬁed

time period has passed. In case of transmission during scan,

pauses scanning. Scanning resumes after a speciﬁed time

period has passed after the transmission is ﬁnished.

➥Push and hold this key for 1 sec. to indicate the scan group,

then select the desired group using [CH Up]/[CH Down].

SCAN B START/STOP KEY

➥Push to start and cancel scanning operation. In case of

transmission during scan, pauses scanning. Scanning re-

sumes after a speciﬁed time period has passed after the

transmission is ﬁnished.

➥Push and hold this key for 1 sec. to indicate the scan

group, then select the desired group using [CH Up]/

[CH Down].

SCAN ADD/DEL (TAG) KEY

Push to add or delete the selected channel to/from the scan

group.

PRIO A/B KEYS

➥Push to select Priority A or Priority B channel.

➥Push and hold [Prio A (Rewrite)] to rewrite the Prio A chan-

nel.

MR-CH 1/2/3/4 KEYS

Push to select an operating channel directly.

MONI (AUDI) KEY

Activates one of (or two of) the following functions on each

channel independently:

• Push and hold to un-mute the channel (audio is emitted; ‘Audible’

condition).

• Push to mute the channel (sets to ‘Inaudible’ only).

• Push to un-mute the channel (sets to ‘Audible’ only).

• Push after the communication is ﬁnished to send a ‘reset code’.

NOTE: The un-mute condition (‘Audible’ condition) may au-

tomatically return to the mute condition (‘Inaudible‘ condi-

tion) after a speciﬁed period depending on programming.

PANEL DESCRIPTION

PUBLIC ADDRESS KEY

While in the hailer mode, push this key for the audio output via

the hailer ampliﬁer. Ask your dealer for details.

While in the normal mode, the audio output via the cable can

be controlled from the transceiver separately from [VOL] control

knob when an optional OPC-617 acc cable is installed.

• This audio output can be used as a ‘public address’ function when an

external audio ampliﬁer and speaker are connected additionally.

• Push this key, then speak into the microphone while pushing the

PTT switch.

• [CH Up]/[CH Down] allow you to set the audio output level from

minimum to maximum.

RX SPEAKER KEY

While in the hailer mode, the external speaker drive function

is also available simultaneously when the external connec-

tions are made for the ‘public address’ function. The received

audio can be heard via the external speaker when this key is

pushed.

• This function is useful when you are out of the vehicle.

• The audio output level is linked to the transceiver’s volume control.

LIGHT KEY

Push to turn the transceiver’s backlight ON for about 5 sec.

when the backlight function is turned OFF in user set mode.

LOCK KEY

Push and hold to electronically lock all programmable keys

except the following:

[Call] (incl. Call A and Call B), [Moni(Audi)] and [Emergency].

HIGH/LOW KEY

Push to select the transmit output power temporarily or per-

manently, depending on the pre-setting.

• Ask your dealer for the output power level for each selection.

C.TONE CH ENT KEY

Push to select the continuous tone channel using [CH Up]/

[CH Down] to change the tone frequency/code setting after

pushing this key. The selected channel remains set as the

continuous tone channel until another channel is designated

as such.

TALK AROUND KEY

Turn the talk around function ON and OFF.

• The talk around function equalizes the transmit frequency to the

receive frequency for transceiver-to-transceiver communication.

WIDE/NARROW KEY

Push to toggle the IF bandwidth between wide and narrow.

• The wide passband width can be selected from 25.0 or 20.0 kHz

using the CS-F70/F1700 cloning software. Ask your Dealer for

details.

DTMF AUTODIAL KEY

➥Push to enter the DTMF channel selection mode.Then select

the desired DTMF channel using [CH Up]/[CH Down].

➥After selecting the desired DTMF channel, push this key to

transmit the DTMF code.

1PANEL DESCRIPTION

RE-DIAL KEY

Push to transmit the last-transmitted DTMF code.

CALL KEYS

Push to transmit a 5-tone/BIIS ID code.

• Call transmission is necessary before calling another station depend-

ing on your signalling system.

• [Call A] and/or [Call B] may be available when your system employs

selective ‘Individual/Group’ calls. Ask your dealer which call is

assigned to each key.

EMERGENCY KEYS

➥Push and hold to transmit an emergency call.

➥When [Emergency Single (Silent)] or [Emergency Repeat

(Silent)] is pushed, an emergency call is transmitted with-

out a beep emission and LCD indication change.*

• If you want to cancel the emergency call, push (or push and hold)

the key again before transmitting the call.

• The emergency call is transmitted one time only or repeatedly

until receiving a control code depending on the pre-setting.

*BIIS PMR operation only

SURVEILLANCE KEY

Push to turn the surveillance function ON or OFF.

When this function is turned ON, the beep is not emitted and

the LCD backlight does not light when a signal is received or

a key is pushed, etc.

TX CODE ENTER KEY

Push to enter the ID code edit mode directly, for both 5-

tone and BIIS. Then set the desired digit using [CH Up]/

[CH Down] or 10-keypad*. (p. 11)

*IC-F1810 or IC-F2810 only

TX CODE CHANNEL SELECT KEY

➥

Push to enter the ID code channel selection mode directly.

Then set the desired channel using [CH Up]/[CH Down].

(p. 10)

➥During ID code channel selection mode, push for 1 sec. to

enter the ID code edit mode for 5-tone and BIIS. Then set

the desired digit using [CH Up]/[CH Down] or 10-keypad*.

(p. 11)

*IC-F1810 or IC-F2810 only

ITX CODE CHANNEL UP/DOWN KEYS

Push (or Rotate)* to select a TX code channel directly.

*Rotate when this function is assigned to [DIAL].

ID-MR SELECT KEY

➥Recalls detected ID codes.

• Push this key, then select the ID code using [CH Up]/[CH

Down].

• Up to 5 ID’s are memorized.

➥Push and hold to erase the selected ID’s.

SCRAMBLER KEY

Push to toggle the voice scrambler function ON and OFF.

Andere Handbücher für IC-F1710

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Icom Transceiver Handbücher

Icom

Icom IC-575A Bedienungsanleitung

Icom

Icom IC-A23 Bedienungsanleitung

Icom

Icom IC-726 Bedienungsanleitung

Icom

Icom IC-M323 Bedienungsanleitung

Icom

Icom UltraTech IC-F4GT-4 Bedienungsanleitung

Icom

Icom IC-7600 Bedienungsanleitung

Icom

Icom IC-M1V Bedienungsanleitung

Icom

Icom IC-746PRO Bedienungsanleitung

Icom

Icom IC-M90E Bedienungsanleitung

Icom

Icom IC-290A/E Bedienungsanleitung

Icom

Icom RS-MS3A Bedienungsanleitung

Icom

Icom IC-775DSP Bedienungsanleitung

Icom

Icom IC-M800 Bedienungsanleitung

Icom

Icom IC-04A Bedienungsanleitung

Icom

Icom IC-4GA Bedienungsanleitung

Icom

Icom IC-F4011 Bedienungsanleitung

Icom

Icom IC-F3 Bedienungsanleitung

Icom

Icom IC-F44GS Bedienungsanleitung

Icom

Icom IC-2710H Bedienungsanleitung

Icom

Icom IC-A200 Bedienungsanleitung

Icom

Icom IC-F14/S Bedienungsanleitung

Icom

Icom IC-725 Bedienungsanleitung

Icom

Icom IC-M1V Bedienungsanleitung

Icom

Icom IC-820H Gebrauchsanweisung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung