Icom IC-F3262DT Bedienungsanleitung

INSTRUCTION MANUAL

The photo shows the

UHF transceiver.

iF4262DT

iF4262DS

UHF TRANSCEIVERS

iF3262DT

iF3262DS

VHF TRANSCEIVERS

IMPORTANT

READ ALL INSTRUCTIONS carefully and com-

pletely before using the transceiver.

SAVE THIS INSTRUCTION MANUAL — This

instruction manual contains important operating instructions

for the IC-F3262DT, IC-F3262DS VHF TRANSCEIVERS and

IC-F4262DT, IC-F4262DS UHF TRANSCEIVERS.

This instruction manual includes some functions which are

usable only when they are preset by your dealer. Ask your

dealer for details.

See the operating guide for details of IDAS™ NXDN™,

BIIS, MDC and LTR®system operations. Ask your dealer

for details.

WORD DEFINITION

RDANGER! Personal death, serious injury or an explo-

sion may occur.

RWARNING! Personal injury, fire hazard or electric

shock may occur.

CAUTION Equipment damage may occur.

NOTE

If disregarded, inconvenience only. No risk

of personal injury, ﬁre or electric shock.

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-

porated (Japan) in Japan, the United States, the United Kingdom, Germany,

France, Spain, Russia and/or other countries.

IDAS is trademark of Icom Incorporated (Japan).

NXDN is a trademark of Icom Incorporated and JVC KENWOOD Corporation.

LTR is a registered trademark of the E.F.Johnson Technologies, INC. in the

United States.

All other products or brands are registered trademarks or trademarks of their

respective holders.

EXPLICIT DEFINITIONS

RDANGER! NEVER short the terminals of the battery

pack.

RDANGER! Use and charge only speciﬁed Icom battery

packs with Icom radios or Icom chargers. Only Icom battery

packs are tested and approved for use with Icom radios or

charged with Icom chargers. Using third-party or counterfeit

battery packs or chargers may cause smoke, ﬁre, or cause

the battery to burst.

RWARNING! NEVER hold the transceiver so that

the antenna is very close to, or touching exposed parts of

the body, especially the face or eyes, while transmitting. The

transceiver will perform best if the microphone is 5 to 10 cm

away from the lips and the transceiver is vertical.

RWARNING! NEVER operate the transceiver with

a headset or other audio accessories at high volume levels.

Hearing experts advise against continuous high volume op-

eration. If you experience a ringing in your ears, reduce the

volume level or discontinue use.

RWARNING! NEVER operate the transceiver while

driving a vehicle. Safe driving requires your full attention—

anything less may result in an accident.

CAUTION: MAKE SURE the ﬂexible antenna, bat-

tery pack and jack cover are securely attached to the trans-

ceiver, and that the antenna and battery pack are dry before

attachment. Exposing the inside of the transceiver to dust or

water will result in serious damage to the transceiver.

DO NOT operate the transceiver near unshielded electri-

cal blasting caps or in an explosive atmosphere.

DO NOT push [PTT] when not actually intending to transmit.

DO NOT use or place the transceiver in direct sunlight or in

areas with temperatures below –25°C or above +55°C.

The basic operations, transmission and reception of the trans-

ceiver are guaranteed within the speciﬁed operating tempera-

ture range. However, the LCD display may not be operate

correctly, or show an indication in the case of long hours of

operation, or after being placed in extremely cold areas.

DO NOT modify the transceiver. The transceiver warranty does

not cover any problems caused by unauthorized modiﬁcation.

DO NOT use harsh solvents such as benzine or alcohol

when cleaning, as they will damage the transceiver surfaces.

BE CAREFUL! The transceiver will become hot when

operating it continuously for long periods of time.

PRECAUTIONS

iii

BE CAREFUL! The transceiver meets IP67 require-

ments for dust-tight and waterproof protection. However, once

the transceiver has been dropped, dust-tight and waterproof

protection cannot be guaranteed because of possible dam-

age to the transceiver’s case or the waterproof seal.

Even when the transceiver power is OFF, a slight current still

ﬂows in the circuits. Remove the battery pack or batteries from

the transceiver when not using it for a long time. Otherwise,

the installed battery pack or batteries will become exhausted,

and will need to be recharged or replaced.

MAKE SURE to turn OFF the transceiver power before

connecting the supplied/optional equipment.

PRECAUTIONS (Continued)

For IC-F4262

• The GPS receiver may not work if the transceiver transmits

near the 510 MHz. This is made in the internal circuit and

does not indicate a transceiver malfunction.

VOICE CODING TECHNOLOGY

The AMBE+2™ voice coding Technology embodied in this

product is protected by intellectual property rights including

patent rights, copyrights and trade secrets of Digital Voice

Systems, Inc. This voice coding Technology is licensed solely

for use within this Communications Equipment. The user of

this Technology is explicitly prohibited from attempting to ex-

tract, remove, decompile, reverse engineer, or disassemble

the Object Code, or in any other way convert the Object Code

into a human-readable form. U.S. Patent Nos.

#5,870,405,#5,826,222,#5,754,974,#5,701,390,#5,715,365,

#5,649,050,#5,630,011,#5,581,656,#5,517,511,#5,491,772,

#5,247,579, #5,226,084 and #5,195,166.

TABLE OF CONTENTS

IMPORTANT .......................................................................... i

EXPLICIT DEFINITIONS....................................................... i

PRECAUTIONS.................................................................... ii

VOICE CODING TECHNOLOGY ........................................ iii

TABLE OF CONTENTS....................................................... iv

1 ACCESSORIES ...........................................................1–3

Supplied accessories■...................................................1

Accessory attachments■................................................1

2 PANEL DESCRIPTION..............................................4–10

Front panel■...................................................................4

Function display■...........................................................5

Programmable function keys■........................................6

3 BASIC OPERATION................................................11–18

Turning power ON■......................................................11

Channel selection■......................................................12

Call procedure■............................................................13

Receiving and transmitting■.........................................13

User set mode■............................................................16

Scrambler function■.....................................................16

Stun function■..............................................................16

Emergency transmission■............................................17

Man Down Emergency Call■........................................17

Automatic Key Lock function■......................................18

Priority A channel selection■........................................18

4 BATTERY CHARGING ............................................19–23

Caution■.......................................................................19

Optional battery chargers■...........................................21

5 BATTERY CASE......................................................24–26

BP-240 optional battery case■.....................................24

BP-261 optional battery case■.....................................25

6 SWIVEL BELT CLIP ................................................27–28

MB-93 contents■..........................................................27

To attach■....................................................................27

To detach■...................................................................28

7 SPEAKER MICROPHONE............................................29

Optional HM-184/HM-184H■.......................................29

To attach■....................................................................29

8 OPTIONS.................................................................30–31

9 COUNTRY CODE LIST .................................................32

1ACCESSORIES

Supplied accessories■

The following accessories are supplied.

Battery pack Belt clip

Connector cover

(with screw)

Flexible antenna

(This illustration is

for the UHF type.)

NOTE: Some accessories are not supplied, depending on

the transceiver version.

Accessory attachments■

Flexible antennaD

Connect the supplied ﬂexible antenna

to the antenna connector.

CAUTION:

• NEVER carry the transceiver by

holding antenna.

• DO NOT connect any antenna

other than those listed on page

31.

• Transmitting without an antenna

will damage the transceiver.

ACCESSORIES

Battery packD

To attach the battery pack:

Slide the battery pack in the direction of the arrow (q) until the

battery release button makes a ‘click’ sound.

NOTE: Push on the bottom of the pack to make sure the

release button is ﬁrmly locked.

To remove the battery pack:

Push the battery release button in the direction of the arrow

(w), as shown below. The battery pack is then removed.

NEVER remove or attach the battery pack when the trans-

ceiver is wet or soiled. This may result water or dust get-

ting into the transceiver/battery pack and may result in the

transceiver being damaged.

Battery release

button

Battery pack

NOTE: Keep the battery pack terminals clean. It’s a good

idea to occasionally clean them.

Belt clipD

To attach the belt clip:

qRemove the battery pack if it is attached.

wSlide the belt clip in the direction of the arrow until the belt

clip locks and makes a ‘click’ sound.

To detach the belt clip:

qRemove the battery pack if it is attached.

wPinch the clip (q), and slide the belt clip in the direction of

the arrow (w).

1ACCESSORIES

Connector coverD

To attach the connector cover:

qPlace the connector cover over the multi-connector.

wTighten the screw.

Multi-

connector

Connector

cover

CAUTION:

Attach the connector cover when optional equipment is not

used. Otherwise the terminals of the multi-connector may

short out, and this could damage the transceiver.

To detach the connector cover:

qRemove the screw using a Phillips screwdriver.

wDetach the connector cover to connect optional equip-

ment.

PANEL DESCRIPTION

Front panel■

Microphone

Speaker

GPS receiver*

*A GPS receiver is

bult-in, depending on

the transceiver version.

qROTARY SELECTOR

Rotate to select the memory channels or the operating

zone, depending on the presetting.

wANTENNA CONNECTOR

Connect the supplied antenna. (p. 1)

eDEALER-PROGRAMMABLE KEY [EMR]

Desired functions can be preset by your dealer.

(p. 6)

rDEALER-PROGRAMMABLE KEY [Side1]

Desired functions can be preset by your dealer.

(p. 6)

tPTT SWITCH [PTT]

Hold down to transmit, release to receive.

yDEALER-PROGRAMMABLE KEYS [Side2]/[Side3]

Desired functions can be preset by your dealer. (p. 6)

u10-KEYPAD (Depending on the version)

The keypad allows you to enter digits to:

• Select memory channels

• Select tone channels

• Select DTMF codes (during transmit)

• Set TX codes

• Start up with the password

iDEALER-PROGRAMMABLE KEYS [P0] to [P3]

Desired functions can be preset by your dealer. (p. 6)

oFUNCTION DISPLAY (p. 5)

Displays a variety of information such as an operating

channel number/name, Set mode contents, DTMF code,

selected functions and so on.

!0 MULTI-CONNECTOR

Connects to optional equipment.

Connector cover

NOTE: Attach the connec-

tor cover when optional

equipment is not used.

See page 3 for details.

!1 BUSY/TRANSMIT INDICATOR

 ➥Lights green while receiving a signal, or when the

squelch is open.

 ➥Lights red while transmitting.

!2 VOLUME CONTROL [VOL]

Rotate to turn the transceiver power ON or OFF, and ad-

just the audio level.

Function display■

SET

CALA TXCU

TXC

q t iuyrew

qSIGNAL STRENGTH ICON

Indicates relative signal strength level.

wLOW POWER ICON

Appears when low output power is selected.

• When the battery power decreases to a specied level, low

power is automatically selected.

eAUDIBLE ICON

 ➥ Appears when the channel is in the ‘audible’ (unmute)

mode.

 ➥ Appears when a matched signal is received.

r COMPANDER ICON

Appears when the compander function is activated.

t SCRAMBLER ICON

Appears when the voice scrambler function is activated.

2PANEL DESCRIPTION

Andere Handbücher für IC-F3262DT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Icom Transceiver Handbücher

Icom

Icom IC-281H Bedienungsanleitung

Icom

Icom IC-M91D Bedienungsanleitung

Icom

Icom IC-F1710 Bedienungsanleitung

Icom

Icom IC-40GX Bedienungsanleitung

Icom

Icom IC-761 Bedienungsanleitung

Icom

Icom UX-9100 Bedienungsanleitung

Icom

Icom IC-7100 Installationsanleitung

Icom

Icom IC-A110 Bedienungsanleitung

Icom

Icom IC-M72 Bedienungsanleitung

Icom

Icom IC-4061T Bedienungsanleitung

Icom

Icom IC-M504A Bedienungsanleitung

Icom

Icom IC-746 Bedienungsanleitung

Icom

Icom IC-M401E Bedienungsanleitung

Icom

Icom iF3002 Bedienungsanleitung

Icom

Icom IC-F3360D Series Bedienungsanleitung

Icom

Icom IC-F520 Leitfaden

Icom

Icom IC-F52D Bedienungsanleitung

Icom

Icom IC-A15 Bedienungsanleitung

Icom

Icom IC-M506 Bedienungsanleitung

Icom

Icom IC-120 Bedienungsanleitung

Icom

Icom IC-V8 Bedienungsanleitung

Icom

Icom IC-22A Bedienungsanleitung

Icom

Icom IC-F3400DP Series Bedienungsanleitung

Icom

Icom IC-A210E Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung