Icom IC-F5120D Series Bedienungsanleitung

OPERATING GUIDE

OPERATING GUIDE FOR

IC-F5120D/F6120D SERIES

MDC 1200 SYSTEM/

IDAS™ OPERATION

Limited functions only

Thank you for purchasing this Icom transceiver.

The MDC 1200 system and IDAS™ (Icom Digital Advanced

System) functions are built into your IC-F5120D/F6120D se-

ries transceiver.

READ ALL INSTRUCTIONS carefully and completely

before using the transceiver.

SAVE THIS OPERATING GUIDE — This operating

guide contains important operating instructions for:

• IC-F5121D, IC-F5122D, IC-F5123D and IC-F5128D VHF

MOBILE TRANSCEIVERS

• IC-F6121D, IC-F6122D, IC-F6123D and IC-F6128D UHF

MOBILE TRANSCEIVERS

INFORMATION: The 10-keypad of the optional HM-152T

DTMF microphone has only DTMF code transmitting ca-

pability. Therefore, IDs and messages cannot be input

using the microphone.

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-

porated (Japan) in Japan, the United States, the United Kingdom, Germany,

France, Spain, Russia and/or other countries.

IDAS and the IDAS logo are trademarks of Icom Incorporated (Japan).

All other products or brands are registered trademarks or trademarks of their

respective holders.

IMPORTANT

The AMBE+2™ voice coding Technology embodied in this

product is protected by intellectual property rights including

patent rights, copyrights and trade secrets of Digital Voice

Systems, Inc. This voice coding Technology is licensed

solely for use within this Communications Equipment.

The user of this Technology is explicitly prohibited from

attempting to extract, remove, decompile, reverse engineer,

or disassemble the Object Code, or in any other way convert

the Object Code into a human-readable form. U.S. Patent

Nos. #8,595,002, #8,359,197, #8,315,860, #8,200,497,

#7,970,606, #6,912,495 B2.

VOICE CODING TECHNOLOGY

TABLE OF CONTENTS

IMPORTANT.......................................................................... i

VOICE CODING TECHNOLOGY .......................................... i

TABLE OF CONTENTS........................................................ ii

1 PREPARATION................................................................1

■Programmable function keys ........................................1

2 MDC 1200 OPERATION..............................................2–3

■MDC 1200 system operation........................................2

■Receiving a call ............................................................2

■Transmitting a call.........................................................3

3 IDAS OPERATION ....................................................4–16

■IDAS operation .............................................................4

■IDAS Trunk operation ...................................................4

■Receiving a call ............................................................4

■Transmitting a call.......................................................10

■Transmitting Position data...........................................15

■Transmitting Status message .....................................15

■Sounding a Horn ........................................................15

■Connecting a Printer ..................................................16

■Using Voice Encryption ..............................................16

1PREPARATION

■Programmable function keys

The following functions can be assigned to the [UP], [DOWN],

[P0], [P1], [P2] and [P3] programmable function keys.

Consult your Icom dealer or system operator for details con-

cerning your transceivers preprogramming.

DFor only IDAS operation

DIGITAL BUTTON KEY

➥Push [Digital Button] to enter the application selection

mode.

➥Hold down for 1 second to toggle the call type between

Individual and Talkgroup, and then automatically enter the

application selection mode.

• Push the [CH Up] or [CH Down] key to select the “VOICE,”

“CALLALRT,” “STATUS,” “MSG,” or “CALL LOG” application.

➥While in the application selection mode, push to enter the

Individual or Talkgroup ID selection mode.

• If “STATUS” or “MSG” is selected as the application, the message

selection mode appears. Push the [CH Up] or [CH Down] key to

select the desired message, then push [Digital Button] again to

enter the Individual or Talkgroup ID selection mode. (pp. 12, 13)

➥

While in the application selection mode, hold down [Digital

Button] for

1 second to return to the normal operating

mode.

STATUS UP/DOWN KEYS

➥When a Short Data Message (SDM) is displayed, push to

cancel the automatic scroll and manually scroll the mes-

sage.

➥When an SDM that contains more than 8 characters is dis-

played, push to manually scroll the message.

MDC 1200 OPERATION

■MDC 1200 system operation

The MDC 1200 signaling system enhances your transceiv-

er’s

capabilities. It allows PTTID*, Emergency signaling, and

receiving a Radio Check. Also, the dispatcher can stun and

revive transceivers on the system.

An additional feature of the MDC 1200 system in Icom trans-

ceivers is called aliasing. Each transceiver on the system has

a unique ID number. Aliasing allows substituting an alphanu-

meric name for the ID number. When transmitting, you can use

this alias to select a transceiver to call. When a call is received,

the alias of the calling station is displayed instead of the ID.

*When [PTT] is pushed or released, the transceiver transmits your

station ID.

NOTE: During MDC 1200 system operation, IDAS opera-

tion capability is disabled.

■Receiving a call

DReceiving an Emergency Call

qWhen an emergency call is received:

• Beeps sound.

• The calling station ID (or alias) and “EMG EMG” are alternately

displayed.

To stop the beep and display indication, turn OFF the

power, change the channel or push [PTT].

DReceiving a Stun and Revive

The dispatcher can send MDC 1200 system signals that

will stun or revive your transceiver. If a Stun command that

matches your station ID is received, the transceiver will dis-

play “SORRY” (default) and you cannot receive* or transmit.

When a Revive command that matches your station ID is

received, normal operation is restored and “SORRY” disap-

pears.

(* Except Revive command signals)

2MDC 1200 OPERATION

■Transmitting a call

DPTTID Calls

The transceiver can send an MDC 1200 system signal that

includes PTTID when [PTT] is pushed (begin transmitting)

and released (stop transmitting). If a PTTID call is received,

the transceiver will display the calling station’s ID (or alias)

and sound a beep.* (*Depending on the preprogramming.)

DTransmitting an Emergency Call

When [Emergency] (described in the instruction manual) is

held down for a speciﬁed time period,* the emergency signal

is once or repeatedly transmitted on the speciﬁed emergency

channel.

When no emergency channel is specified, the call is

transmitted on the operating channel.

The repeat emergency signal is automatically transmitted

until you turn OFF the power.

Depending on the preprogramming, receiving an

acknowledgement may cancel the transmission.

If you want to cancel the Emergency function, hold down

[Emergency] for the preprogrammed time period again before

transmitting the call.

If your transceiver is programmed for Silent operation, you

can transmit emergency calls without the beep sounding and

the LCD display changing.

IMPORTANT: Setting an individual emergency channel is

recommended for dependable emergency call operation.

*Depending on the preprogramming, the following functions can be

automatically activated. Ask your dealer for details.

DNOTES

• Auto TX function

After an emergency call transmission, audio from the

microphone is automatically transmitted for a speciﬁed time

period.

• The HM-148G or HM-152 hand microphone is required.

• Auto RX function

After an emergency call transmission, the transceiver stands

by in the audible mode for a speciﬁed time period.

IDAS OPERATION

■IDAS operation

The IC-F5120D and IC-F6120D series use the Icom Digital

Advanced System (IDAS) that meets the 6.25 kHz emission

mask requirements for narrow banding. IDAS increases ef-

ﬁciency of channel allocation and use of the RF spectrum.

NOTE: During IDAS operation, MDC 1200 system opera-

tion capability is disabled.

■IDAS Trunk operation

The IDAS Trunk system enables further effective channel

management by sharing a minimum of channels with a large

number of users.

Push [Zone], then push [CH Up] or [CH Down]* to select the

IDAS Trunk zone.

* The method to select the desired zones may differ, depending on

your system set up.

NOTE: During IDAS Trunk operation, you can receive and

transmit digital calls in the same way as IDAS operation,

as described in ‘■Receiving a call,’ ‘■Transmitting a call.’

■Receiving a call

DReceiving a Voice Call

qWhen a Voice call is received:

• Mute is released.

• While receiving the signal, either the calling station or Talkgroup

ID name (or code) can be displayed, depending on the prepro-

gramming.

• When an All Call signal is received, “ALL CALL” is displayed.

The calling station or

Talkgroup ID name

wHold down [PTT], then speak into the microphone.

eRelease [PTT] to receive.

■Receiving a call (continued)

DReceiving a Call Alert

qWhen a Call Alert signal is received:

• Beeps sound.

• “ ” blinks.

• The calling station or Talkgroup ID name (or code) and

“CALLALRT” alternately appear.

The calling station or

Talkgroup ID name

Blinks

wHold down [PTT], then speak into the microphone.

eRelease [PTT] to receive.

DReceiving a Status Message

qWhen a Status Message is received:

• Beeps sound.

• The calling station or Talkgroup ID name (or code) and the sta-

tus message alternately appear.

The calling station or

Talkgroup ID name

The status

message

wTo clear the ID and message display, push [PTT], turn OFF

the power or change the channel.

3IDAS OPERATION

IDAS OPERATION

DReceiving a Message

qWhen a Message is received:

• Beeps sound.

• The calling station ID name (or code) and the message alter-

nately appear.

The calling station or

Talkgroup ID name

The message

NOTE: When the message includes more than

8 characters, and the automatic scroll function is activated,

the message automatically scrolls.

• Push [Status Up] or [Status Down] to manually scroll the mes-

sage.

Scrolls

wTo clear the ID and message display, push [PTT], turn

power OFF or change the channel.

DReceiving a Stun, Kill or Revive

If an Individual call with a Stun or Kill command is received,

the transceiver will display “SORRY” and you can not receive*

or transmit. (RAN code matching may not be necessary, de-

pending on the preprogramming.)

* Depending on the received Stun command setting. Revive signals

can always be received.

➥When a Stun command is received:

• The transceiver cannot be operated until an Individual call a Re-

vive command is received, or you enter a password. (RAN code

matching may not be necessary, depending on the preprogram-

ming.)

➥When a Kill command is received:

• The transceiver cannot be operated until data cloning is per-

formed. Ask your dealer for details.

NOTE: Depending on the preprogramming, the transceiver

can ignore the Stun, Revive and Kill commands that are

from a non-speciﬁed station.

3IDAS OPERATION

■Receiving a call (continued)

DReceiving a Remote Monitor, Radio Check

or Status Polling Call

If an Individual call with a Remote monitor, Radio Check or

Status polling command is received, the transceiver will au-

tomatically transmit. (RAN code matching may not be neces-

sary, depending on the preprogramming.)

➥When a Remote monitor command is received:

• The microphone audio is automatically transmitted for the set

time period.

➥When a Radio Check command is received:

• An acknowledgement call is automatically transmitted.

➥When a Status polling command is received:

• A status call is automatically transmitted.

DReceiving an Emergency call

qWhen an emergency call is received:

• Beeps sound.

• “STAT EMR” and the calling station ID name (or code) alternately

appear.

• The state of the backlight depends on the Backlight setting in

the User Set mode. When “LIGT AUT” is selected, the backlight

turns ON for the preprogrammed time period. (Auto Backlight

Timer)

The calling station

ID name

wTo clear the beep, ID and message display, turn OFF the

power or change the channel.

Andere Handbücher für IC-F5120D Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Icom Transceiver Handbücher

Icom

Icom IC-F210 Bedienungsanleitung

Icom

Icom IC-737A Bedienungsanleitung

Icom

Icom IC-F4GS Bedienungsanleitung

Icom

Icom PMR446 Bedienungsanleitung

Icom

Icom IC-M801E Bedienungsanleitung

Icom

Icom iF3230D Series Bedienungsanleitung

Icom

Icom IC-04A Bedienungsanleitung

Icom

Icom IC-706MKII Bedienungsanleitung

Icom

Icom ic-f5021 Bedienungsanleitung

Icom

Icom IC-229A Bedienungsanleitung

Icom

Icom IC-F20 Bedienungsanleitung

Icom

Icom IC-V85 Bedienungsanleitung

Icom

Icom IC-V82-T Bedienungsanleitung

Icom

Icom IC-735 Bedienungsanleitung

Icom

Icom IC-M88 Bedienungsanleitung

Icom

Icom IC-375A Bedienungsanleitung

Icom

Icom IC-F3061T Bauanleitung

Icom

Icom IC-u2A Bedienungsanleitung

Icom

Icom IC-F3400DP Series Bedienungsanleitung

Icom

Icom IC-M600 Bedienungsanleitung

Icom

Icom IC-M604A Bedienungsanleitung

Icom

Icom IC-F1610 Bedienungsanleitung

Icom

Icom IC-F8100 Bedienungsanleitung

Icom

Icom IC-728 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung