Icom IC-F52D Bedienungsanleitung
– 1 –
ACCESSORIES GUIDE
VHF/UHF DIGITAL TRANSCEIVERS
Iç-F52D Thank you for choosing this Icom product. READ
ALL INSTRUCTIONS carefully and completely
before using this product.
This guide describes about the IC-F52D/IC-F62D’s
accessories and option details.
Supplied accessories
Iç-F62D
Battery pack Belt clip Connector cover
(with a screw)
NOTE:
• Some accessories are not supplied, or the shape
is different, depending on the transceiver version.
• Conrmbothbatteryslidinglocksarelocked
in place, when attaching the battery to the
transceiver. Both sliding locks make a ‘click’ sound
when locked.
Attaching accessories
DFlexible antenna
Connecttherequiredexibleantennatotheantenna
connector.
CAUTION:
• DO NOT carry the transceiver by holding only the
antenna.
• DO NOT connect an antenna other than those
listed in the INSTRUCTIONS.
• Transmitting without an antenna may damage the
transceiver.
DBattery pack
CAUTION: DO NOT attach or detach the battery
pack when the transceiver is wet or soiled. This may
result in water or dust getting into the transceiver/
battery pack and may damage the transceiver.
To attach:
1. Slide the battery pack in the direction of the
arrow. (q)
2. Push the battery pack until the battery sliding
locks make a ‘click’ sound. (w)
To detach:
1. Push both battery sliding locks in the direction of
the arrow. (z)
• The battery pack is then released.
2. Lift up to detach the battery pack. (x)
NOTE: Keep the battery pack terminals clean. It’s a
good idea to occasionally clean them.
Battery sliding locks
Battery pack
qq
w
x
z
z
– 2 –
Attaching accessories (Continued)
DBelt clip
To attach:
1. Remove the battery pack from the transceiver, if
it is attached.
2. Slide the belt clip in the direction of the arrow until
the belt clip is locked and makes a ‘click’ sound.
BE CAREFUL! DO NOTbreakyourngernail.
To detach:
Lift the tab up (q), and slide the belt clip in the
direction of the arrow (w).
Belt clip
q
w
DConnector cover
CAUTION: BE SURE to attach the connector cover
when an optional device is not in use. Otherwise the
terminals of the multi-connector may be shorted by
a metal object, or become rusty by water intrusion.
This could damage the transceiver.
To attach:
1. Attach the connector cover over the multi-
connector. (q)
2. Tighten the screw. (w)
To detach:
1. Remove the screw. (z)
2. Detach the connector cover, and then connect an
optional device. (x)
q
w
x
z
– 3 –
Options
Belt clip
Turn OFF the transceiver
before attaching or
detaching the microphone
NOTE:
•NEVER immerse the connector in water. If the
connector becomes wet, BE SURE to dry it before
attaching to the transceiver.
• The microphone element is located at the top
left of the speaker microphone, as shown in the
illustrationabove.Tomaximizethereadability
of your transmitted audio, hold the microphone
approximately5to10cm(2to4inches)fromyour
mouth, and then speak at your normal voice level.
To attach:
Attach the connector of the speaker microphone to
the multi connector on the transceiver and tighten the
screw.
[PTT]
[Emer]
Speaker
Microphone
Earphone
jack
Turn OFF
Screw
Coin
CAUTION: Firmly attach to the multi
connector, but do not overtighten.
A loose connection will allow water
intrusion into the connector.
Over-tightening the connection can
damage the transceiver.
NOTE: KEEP the connector cover attached to the
transceiver when the speaker microphone is not in
use.
Water will not get into the transceiver, even if the
cover is not attached. However, the terminals (pins)
will become rusty, or the transceiver will function
abnormally if the connector becomes wet.
You can connect
an earphone
(user supplied)
to the earphone
jack on the
microphone.
DHM-222 speaker microphone
–4–
DMB-136 belt clip
Belt clip Base clip
To attach:
1. Detach the battery pack, if attached.
2. Slide the base clip in the direction of the arrow
until the clip locks and makes a “click” sound.
3. Attach the battery pack to the transceiver.
Base clip
Battery pack
4. Clip the belt clip on your belt.
5. Insert the transceiver upsidedown into the belt
clip until the base clip is fully inserted in the
groove.
NOTE: Holdthetransceiverrmlywhen
inserting the transceiver into the belt clip.
6. Once the transceiver is locked in place, it swivels,
as shown below.
NOTE: If the transceiver has been accidentally
dropped and the base clip is scratched or
damaged, the transceiver may not be properly
attached to the holder or swivel.
Once the transceiver is locked on place,
itswivels360degrees.
Options (Continued)
To detach:
1. Turn the transceiver upsidedown in the direction
of the arrow and pull it out of the belt clip.
NOTE: Holdthetransceiverrmlywhen
removing the transceiver from the belt clip.
2. Detach the battery pack. (p. 1-3)
3. Lift up the tab on the base clip (q), and then slide
the clip in the direction of the arrow (w).
BE CAREFUL! DO NOTbreakyourngernail.
q
wBattery
pack
– 5 –
Options (Continued)
DBC-226 desktop charger
Chargingtime:approximately2.7hoursfortheBP-290
LTo connect the power adapter
to the charger, remove the
charger’s left cover.
Turn OFF
BC-226
Power adapter*
(BC-228)
Battery pack
Connecting BC-226 together
You can connect up to 6 BC-226 together.
1. Remove the charger’s right cover. (q)
2. Snap the DC power plug to the another charger’s
DC power jack. (w)
WARNING: DO NOT connect more than 6 chargers
together. It may result in an electric shock, cause a
re,overheating,ordamagechargers.
Status indicator information
Light color Status
Orange Charging
Green Charging is completed.
Blinks orange and green Charging failed. It may have
some problems.
Fuse replacement
Ifafuseblows,ndandrepairthecauseofthe
problem. Then replace the damaged fuse with a new,
adequately rated fuse.
Fusetype:5A/58V(lowprolemini blade fuse)
NOTE:
• The transceiver MUST be turned OFF while charging. Otherwise:
- The battery will not be charged properly.
- The battery life may be shortened.
• Do not transmit while charging. When you need to transmit, remove the transceiver from the charger, and then
turn ON the power.
• If the battery pack does not properly charge when it is attached to the transceiver, remove it from the
transceiver and insert only the battery pack into the charger.
Status indicator
* May not be supplied, or the shape may be different, depending on the version.
CAUTION: Readthe‛Batterycaution’and‛Chargingcaution’
on the PRECAUTIONS before using the charger.
NOTE: Remove the fuse using the needle-nose pliers.
Fuse
Battery pack + Transceiver
– 6 –
A7397-8EX
©2017IcomInc.
1-1-32Kamiminami,Hirano-ku,Osaka547-0003,Japan
Options (Continued)
BC-226 Specications
• Dimensions(projectionsarenotincluded.): 106.5(W)×49(H)×78(D)mm,
4.2(W)×1.9(H)×3.1(D)inches
When6chargersareconnectedtogether 542(W)×49(H)×78(D)mm,
21.3(W)×1.9(H)×3.1(D)inches
• Weight(approximately): 120g,4.2oz
When6chargersareconnectedtogether 640g,22.6oz
• Chargingtemperaturerange: 15˚C~40˚C,59˚F~104˚F
• Powersupplyrequirement: 12~16VDCorthespeciedpoweradapter(BC-228)
Andere Handbücher für IC-F52D
3
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Icom Transceiver Handbücher
Icom
Icom IC-T8A Bedienungsanleitung
Icom
Icom IC-M3EURO Bedienungsanleitung
Icom
Icom IC-T70A Bedienungsanleitung
Icom
Icom IC-M710 Bedienungsanleitung
Icom
Icom IC-F14 Bedienungsanleitung
Icom
Icom IC-725 Bedienungsanleitung
Icom
Icom IC-2340H Bedienungsanleitung
Icom
Icom IC-7851 Bauanleitung
Icom
Icom IC-M23 Bedienungsanleitung
Icom
Icom IC-A23 Bedienungsanleitung
Icom
Icom IC-F30GT Bedienungsanleitung
Icom
Icom IC-F5330D Bedienungsanleitung
Icom
Icom IC-M421 Bedienungsanleitung
Icom
Icom IC-4SA Bedienungsanleitung
Icom
Icom iF22SR Bedienungsanleitung
Icom
Icom IC-M710 Bedienungsanleitung
Icom
Icom IC-M422 Bedienungsanleitung
Icom
Icom D-STAR ID-31A; D-STAR ID-31E Bedienungsanleitung
Icom
Icom IC-M502 Bedienungsanleitung
Icom
Icom IC-F51V Bedienungsanleitung
