Icom IC-F9511S Bedienungsanleitung

INSTRUCTION MANUAL

This device complies with Part 15 of the FCC Rules.

Operation is subject to the condition that this device does

not cause harmful interference.

VHF MOBILE TRANSCEIVER

iF9511S

iF9511T

RWARNING! NEVER connect the transceiver to an

AC outlet. This may pose a ﬁre hazard or result in an electric

shock.

NEVER connect the transceiver to a power source of

more than 16 V DC such as a 24 V battery. This connection

will ruin the transceiver.

NEVER cut the DC power cable between the DC plug and

fuse holder. If an incorrect connection is made after cutting,

the transceiver might be damaged.

NEVER place the transceiver where normal operation of

the vehicle may be hindered or where it could cause bodily

injury.

NEVER allow children to touch the transceiver.

NEVER expose the transceiver to rain, snow or any liq-

uids.

USE the specified microphone only. Other microphones

have different pin assignments and may damage the trans-

ceiver.

DO NOT use or place the transceiver in areas with tem-

peratures below –30°C (–22°F) or above +60°C (+140°F), or

in areas subject to direct sunlight, such as the dashboard.

PRECAUTIONS

WORD DEFINITION

RWARNING Personal injury, fire hazard or electric

shock may occur.

CAUTION Equipment damage may occur.

NOTE If disregarded, inconvenience only. No risk

of personal injury, ﬁre or electric shock.

READ ALL INSTRUCTIONS carefully and com-

pletely before using the transceiver.

SAVE THIS INSTRUCTION MANUAL — This

instruction manual contains important operating instructions

for the IC-F9511S/T VHF MOBILE TRANSCEIVERS.

IMPORTANT

Icom, Icom Inc. and the logo are registered trademarks of Icom Incorpo-

rated (Japan) in the United states, the United Kingdom, Germany, France,

Spain, Russia and/or other countries.

All other products or brands are registered trademarks or trademarks of their

respective holders.

EXPLICIT DEFINITIONS

See the operating guide for details of MDC 1200 system

and P25 Trunking system operations. Ask your dealer for

details.

PRECAUTIONS

AVOID operating the transceiver without running the ve-

hicle’s engine. The vehicle’s battery will quickly run out if the

transceiver transmits while the vehicle’s engine OFF.

AVOID placing the transceiver in excessively dusty envi-

ronments.

AVOID placing the transceiver against walls. This will ob-

struct heat dissipation.

AVOID the use of chemical agents such as benzine or

alcohol when cleaning, as they damage the transceiver sur-

faces.

BE CAREFUL! The transceiver will become hot when

operating continuously for long periods.

For U.S.A. only

CAUTION: Changes or modifications to this transceiver, not ex-

pressly approved by Icom Inc., could void your authority to operate

this transceiver under FCC regulations.

ABOUT APCO PROJECT 25

This device made under license under one or more of the

following US patents: #4,590,473, #4,636,791, #5,148,482,

#5,185,796, #5,271,017, #5,377,229.

The IMBE™ voice coding Technology embodied in this prod-

uct is protected by intellectual property rights including patent

rights, copyrights and trade secrets of Digital Voice Systems,

Inc. This voice coding Technology is licensed solely for use

within this Communications Equipment. The user of this Tech-

nology is explicitly prohibited from attempting to decompile,

reverse engineer, or disassemble the Object Code, or in any

other way convert the Object Code into a human-readable

form. U.S. Pat. Nos. #5,870,405, #5,826,222, #5,754,974,

#5,701,390, #5,715,365, #5,649,050, #5,630,011,

#5,581,656, #5,517,511, #5,491,772, #5,247,579,

#5,226,084, #5,195,166.

iii

TABLE OF CONTENTS

IMPORTANT.......................................................................... i

EXPLICIT DEFINITIONS....................................................... i

PRECAUTIONS..................................................................... i

ABOUT APCO PROJECT 25 ............................................... ii

TABLE OF CONTENTS....................................................... iii

1 PANEL DESCRIPTION................................................1–8

 n Front panel ...................................................................1

 n Function display ...........................................................2

 n Programmable function keys........................................3

2 BASIC OPERATION..................................................9–13

 n Turning power ON ........................................................9

 n Channel selection.........................................................9

 n Call procedure............................................................10

 n Receiving and transmitting.........................................10

 n User set mode............................................................13

 n Scrambler function .....................................................13

3 CONNECTION AND MAINTENANCE ....................14–16

 n Rear panel connection ...............................................14

 n Supplied Accessories.................................................15

 n Mounting the transceiver ............................................16

 n Antenna......................................................................16

 n Fuse replacement ......................................................16

 n Cleaning .....................................................................16

4 OPTIONS.......................................................................17

5 SAFETY TRAINING INFORMATION.............................18

PANEL DESCRIPTION

I c o m I n c

yo ru ti

qe*w

IC-F9511S

IC-F9511T

nFront panel

qAF VOLUME CONTROL KNOB

Rotate the knob to adjust the audio output level.

• Minimum audio level is pre-programmed.

wFUNCTION DISPLAY (p. 2)

 

Displays a variety of information, such as an operating

channel number/name, 2-tone code, DTMF numbers and

audible condition, etc.

eDIAL or UP/DOWN KEYS

• IC-F9511S: DIAL

Rotate to select an operating channel, etc.

• IC-F9511T: UP/DOWN Keys

Push to select an operating channel, etc.

*The desired function can be assigned by your dealer. (p. 3)

r10-KEYPAD (IC-F9511T only)

 

The keypad allows you to enter digits to:

• Select memory channels, tone channels and DTMF codes

(when in the DTMF code channel selection mode)

• Set TX code number

• Input text message for SDM operation

• Start up with a password

• Input the Individual ID code for digital operation.

tBUSY INDICATOR

 

Lights green while receiving a signal, or when the squelch

is open.

1PANEL DESCRIPTION

yPOWER SWITCH [POWER]

Push to turn the power ON and OFF.

• The following functions are available at power ON as options:

- Automatic scan start

- Password prompt

- Set mode

uTRANSMIT INDICATOR

 

Lights red while transmitting.

iDEALER-PROGRAMMABLE KEYS

 

Desired functions can be programmed independently by

your dealer. (p. 3)

In this instruction manual, these keys are from the left,

called [P0]/[P1]/[P2]/[P3]/[P4].

oMICROPHONE CONNECTOR

 

Connect the supplied microphone or optional DTMF mi-

crophone.

NEVER connect non-specified microphones. The pin

assignments may be different and the transceiver may

be damaged.

DMICROPHONE

The supplied microphone has a PTT switch and a hanger

hook.

• The following functions are available when the microphone is on or

off hook:

- Automatic scan start when on hook.

- Automatic priority channel selection when off hook.

- Sets to ‘Inaudible’ condition (mute condition) when on hook.

- Sets to ‘Audible’ condition (unmute condition) when off hook.

nFunction display

1 3 6 . 1 N a r

q w e r t y u i o

q SIGNAL STRENGTH INDICATOR

Indicates relative signal strength level.

wLOW POWER INDICATOR

Appears when low output power is selected.

eAUDIBLE INDICATOR

 ➥Appears when the channel is in the ‘audible’ (unmute)

condition.

 ➥Appears when the speciﬁed 2-tone code is received.

rCOMPANDER INDICATOR

Appears when the compander function is activated.

tSCRAMBLER INDICATOR

Appears when the voice scrambler function is activated.

PANEL DESCRIPTION

yBELL INDICATOR

 

Appears/blinks when the speciﬁc 2-tone code is received,

according to the pre-programming.

uCALL CODE MEMORY INDICATOR

 

Appears when the call code memory is selected.

iSDM MEMORY INDICATOR

 

Appears when the SDM memory is displayed.

oSDM INDICATOR

 

Appears when an SDM is received, or a transmit SDM is

selected.

!0 ALPHANUMERIC DISPLAY

 

Displays an operating channel number, channel name,

Set mode contents, DTMF code, etc.

The indication mode can be selected from 1 line or 2

lines. Ask your dealer for details.

In this instruction manual, the LCD illustration is de-

scribed using the 2 lines indication mode.

!1 ACTIVATED KEY INDICATOR

 

Appears above the key assigned as [DIGITAL] key when

that key has been activated.

nProgrammable function keys

The following functions can be assigned to [DIAL]*, [UP],

[DOWN], [P0], [P1], [P2], [P3] and [P4] programmable func-

tion keys.

Consult your Icom dealer or system operator for details con-

cerning your transceivers programming.

If the programmable function names are bracketed in the fol-

lowing explanations, the speciﬁc key is used to activate the

function depends on the programming.

*The functions you can assign to [DIAL] are limited.

(Only functions marked with ✩can be assigned.)

✩CH UP AND DOWN KEYS

➥Push (or Rotate)* to select an operating channel.

➥Push (or Rotate)* to select a transmit code channel after

pushing [TX Code CH Select].

➥Push (or Rotate)* to select a DTMF channel after pushing

[DTMF Autodial].

➥Push (or Rotate)* to select a scan group after pushing

and holding [Scan A Start/Stop]/[Scan B Start/Stop].

➥Push (or Rotate)* to select an Individual ID code or Talk-

group ID code after pushing [Individual] or [Talkgroup].

*Rotate when this function is assigned to [DIAL].

✩

ZONE UP AND DOWN KEY (This function is for [DIAL] only)

Rotate to select the desired zone.

1PANEL DESCRIPTION

ZONE KEY

Push this key, then select the desired zone using [CH Up]/

[CH Down].

What is “zone”?—The desired channels are assigned

into a zone according to the intended use for grouping.

For example, ‘Staff A’ and ‘Staff B’ are assigned into a

“Business” zone, and ‘John’ and ‘Cindy’ are assigned into

a “Private” zone.

SCAN A START/STOP KEY

➥This key’s operation depends on the Power ON Scan set-

ting.

When the power ON scan function is turned OFF;

Push to start and cancel scanning operation. In case of

transmission during scan, cancels scanning.

When the power ON scan function is turned ON;

Push to pause scanning. Scanning resumes after a

speciﬁed time period has passed. In case of transmission

during scan, pauses scanning. Scanning resumes after a

speciﬁed time period has passed after the transmission is

ﬁnished.

➥Push and hold this key for 1 sec. to indicate the scan group,

then select the desired group using [CH Up]/[CH Down].

SCAN B START/STOP KEY

➥Push to start and cancel scanning operation. In case of

transmission during scan, pauses scanning. Scanning re-

sumes after a speciﬁed time period has passed after the

transmission is ﬁnished.

➥Push and hold this key for 1 sec. to indicate the scan

group, then select the desired group using [CH Up]/

[CH Down].

SCAN ADD/DEL (TAG) KEY

Push to add or delete the selected channel to/from the scan

group.

PRIO A/B KEYS

➥Push to select Priority A or Priority B channel.

➥Push and hold [Prio A (Rewrite)] to rewrite the Prio A

channel.

MR-CH 1/2/3/4 KEYS

Push to select an operating channel directly.

MONI (AUDI) KEY

Mute and release the CTCSS (DTCS) or 2-tone squelch

mute. Open any squelch/deactivate any mute while pushing

this key. (LMR operation only)

PANEL DESCRIPTION

PUBLIC ADDRESS KEY

While in the hailer mode, push this key for the audio output

via the hailer ampliﬁer. Ask your dealer for details.

While in the normal mode, the audio output via the cable

can be controlled from the transceiver separately from [VOL]

control knob.

• This audio output can be used as a ‘public address’ function when

an external audio ampliﬁer and speaker are connected additionally.

• Push this key, then speak into the microphone while pushing the

PTT switch.

• [CH Up]/[CH Down] allow you to set the audio output level from

minimum to maximum.

RX SPEAKER KEY

While in the hailer mode, the external speaker drive function

is also available simultaneously when the external connec-

tions are made for the ‘public address’ function. The received

audio can be heard via the external speaker when this key is

pushed.

• This function is useful when you are out of the vehicle.

• The audio output level is linked to the transceiver’s volume control.

LIGHT KEY

Push to turn the transceiver’s backlight ON for about 5 sec.

when the backlight function is turned OFF in user set mode.

LOCK KEY

Push and hold to electronically lock all programmable keys

except the following:

[Call] (incl. Call A and Call B), [Moni(Audi)] and [Emergency].

HIGH/LOW KEY

Push to select the transmit output power temporarily or per-

manently, depending on the pre-setting.

• Ask your dealer for the output power level for each selection.

C.TONE CH ENT KEY

Push to select the continuous tone channel using [CH Up]/

[CH Down] to change the tone frequency/code setting after

pushing this key. The selected channel remains set as the

continuous tone channel until another channel is designated

as such.

TALK AROUND KEY

Turn the talk around function ON and OFF.

• The talk around function equalizes the transmit frequency to the

receive frequency for transceiver-to-transceiver communication.

WIDE/NARROW KEY

Push to toggle the IF bandwidth between wide and narrow.

DTMF AUTODIAL KEY

➥

Push to enter the DTMF channel selection mode. Then

select the desired DTMF channel using [CH Up]/[CH Down].

➥After selecting the desired DTMF channel, push this key

to transmit the DTMF code.

SCRAMBLER FUNCTION

Push to toggle the voice scrambler function ON and OFF.

1PANEL DESCRIPTION

RE-DIAL KEY

Push to transmit the last-transmitted DTMF code.

CALL KEYS

Push to transmit a 2-tone ID code.

• Call transmission is necessary before calling another station

depending on your signalling system.

• [Call A] and/or [Call B] may be available when your system

employs selective ‘Individual/Group’ calls. Ask your dealer which

call is assigned to each key.

EMERGENCY KEYS

➥Push and hold to transmit an emergency call.

➥When [Emergency Single (Silent)] or [Emergency Repeat

(Silent)] is pushed, an emergency call is transmitted with-

out a beep emission and LCD indication change.

• If you want to cancel the emergency call, push (or push and

hold) the key again before transmitting the call.

• The emergency call is transmitted one time only or repeatedly

until receiving a control code depending on the pre-setting.

SURVEILLANCE KEY

Push to turn the surveillance function ON or OFF.

When this function is turned ON, the beep is not emitted and

the LCD backlight does not light when a signal is received or

a key is pushed, etc.

COMPANDER KEY

Push to toggle the compander function ON and OFF.

The compander function reduces noise components from

the transmitted audio to provide clear communication.

TX CODE CHANNEL SELECT KEY

Push to enter the ID code channel selection mode directly.

Then set the desired channel using [CH Up]/[CH Down].

(p. 11)

✩TX CODE CHANNEL UP/DOWN KEYS

Push (or Rotate)* to select a TX code channel directly.

*Rotate when this function is assigned to [DIAL].

HOOK SCAN KEY

When the hook on scan function is turned ON, push this key

to stop scanning temporarily. Push this key again to re-start

scanning.

USER SET MODE KEY

➥Push and hold to enter user set mode.

• During user set mode, push this key to select an item, and

change the value or condition using push [CH Up]/[CH Down].

➥Push and hold this key again to exit user set mode.

User set mode is also available via the ‘Power ON function.’

Refer to p. 13 also.

OPT 1/2/3 KEYS

Push to control the output signal level from the optional unit

connector.

Andere Handbücher für IC-F9511S

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Icom Transceiver Handbücher

Icom

Icom IC-2SE Bedienungsanleitung

Icom

Icom ic-2730A Bedienungsanleitung

Icom

Icom C-F43GS Bedienungsanleitung

Icom

Icom IC-M800 Bedienungsanleitung

Icom

Icom IC-2SAT Bedienungsanleitung

Icom

Icom IC-M323 Bedienungsanleitung

Icom

Icom IC-M5 Bedienungsanleitung

Icom

Icom IC-2410A Bedienungsanleitung

Icom

Icom IC-F121 Bedienungsanleitung

Icom

Icom IC-F3161 Series Bedienungsanleitung

Icom

Icom IC-F14 Bedienungsanleitung

Icom

Icom IC-M93D EURO Bedienungsanleitung

Icom

Icom IC-M85UL Bedienungsanleitung

Icom

Icom IC-F40GT Bedienungsanleitung

Icom

Icom IC-F2721 Bedienungsanleitung

Icom

Icom IC-M35 Bedienungsanleitung

Icom

Icom IC-4088SR Bedienungsanleitung

Icom

Icom IC-737 Bedienungsanleitung

Icom

Icom IC-M88 Bedienungsanleitung

Icom

Icom F2000T 84 USA Bedienungsanleitung

Icom

Icom IC-E80D Bedienungsanleitung

Icom

Icom IC-720A Bedienungsanleitung

Icom

Icom IC-706MKII Bedienungsanleitung

Icom

Icom IC-F43TR Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung