Icom IC-M710RT Bedienungsanleitung

INSTRUCTION MANUAL

MF/HF MARINE TRANSCEIVER

iM710RT

IC-M710RT.qxd 02.1.9 9:03 Page A

IMPORTANT

READ THIS INSTRUCTION MANUAL CAREFULLY

before attempting to operate the transceiver.

SAVE THIS INSTRUCTION MANUAL—This manual

contains important safety and operating instructions for

the IC-M710RT MF/HF MARINE TRANSCEIVER.

EXPLICIT DEFINITIONS

The explicit definitions described below apply to this

instruction manual.

☞NOTE: The IC-M710RTGMDSS version has a

high-stability crystal oscillator unit. This unit draws a

slight current even when power to the transceiver

is OFF. To prevent battery exhaustion when dock-

ing your vessel for extended periods, unplug the

DC cable from the DC power receptacle.

PRECAUTIONS

WORD DEFINITION

RWARNING Personal injury, fire hazard or electric

shock may occur.

CAUTION Equipment damage may occur.

NOTE If disregarded, inconvenience only. No risk

of personal injury, ﬁre or electric shock.

RWARNING! NEVER connect the transceiver to an

AC outlet directly. This may pose a ﬁre hazard or re-

sult in an electric shock.

RWARNING! NEVER mount the transceiver over-

head. The weight of the transceiver is approximately 8

kg., but its apparent weight will increase several fold

due to wave shocks and vibration. The transceiver

must be mounted on a ﬂat hard surface only.

NEVER connect a power source of more than 16 V DC

such as a 24 volt battery. This connection will ruin the

transceiver.

NEVER place the transceiver where normal operation

of the ship or vehicle may be hindered or where it

could cause bodily injury.

Place unit in a secure place to avoid inadvertent use

by children.

NEVER expose the transceiver to rain, snow or any

liquids.

There are two types of grounding systems available for

the IC-M710RT—Negative Ground and Floating

Ground—NEVER install the negative ground type to a

plus-grounding ship. Such a connection might blow

fuses and is not usable.

DO NOT use chemical agents such as benzene or al-

cohol when cleaning, as they can damage the trans-

ceiver’s surfaces.

In maritime mobile operation, KEEP the transceiver

and microphone as far away as possible (at least 1 m)

from the magnetic navigation compass to prevent er-

roneous indications.

USE an Icom microphone and/or handset only (sup-

plied or optional). Other brands may have different pin

assignments and may damage the transceiver.

AVOID using or placing the transceiver in areas with

temperatures below –20°C (–4°F) or above +60°C

(+140°F).

AVOID connecting the transceiver to a power source

using reverse polarity. This connection will not only

blow fuses but may also damage the transceiver.

AVOID placing the transceiver in excessively dusty en-

vironments or in direct sunlight.

AVOID placing the transceiver against walls or putting

anything on top of the transceiver. This will obstruct

heat dissipation.

IC-M710RT.qxd 02.1.9 9:03 Page ii

iii

IN CASE OF EMERGENCY (for maritime operation)

VERSIONS

If your vessel requires assistance, contact other ves-

sels and the Coast Guard by sending a distress call on

2182 kHz.

Or, transmit your distress call using digital selective

calling on 2187.5 kHz.

The following versions are available for the

IC-M710RT:

❍USING 2182 kHz WITH VOICE

➀Push [2182kHz] to select the emergency fre-

quency.

➁Push [ALARM] and [TX FREQ] for 1 sec. to trans-

mit a 2-tone alarm signal for at least 30 sec.

• The transceiver automatically stops the alarm after 50

sec.

➂Push [ALARM] to turn the alarm transmission off,

then push and hold the PTT switch on the micro-

phone and send the following information:

1. “MAYDAY, MAYDAY, MAYDAY.”

2. “THIS IS . . . . . . . . . . . ” (name of vessel)

3. “LOCATED AT . . . . . . . ” (vessel’s position)

4. Give the reason for the distress call.

5. Explain what assistance you need.

6. Give additional information:

• Vessel type

• Vessel length

• Vessel color

• Number of people onboard.

❍USING DIGITAL SELECTIVE CALLING

(Only for GMDSS versions with an optional GM-

110DSC

DSC TERMINAL UNIT

)

When immediate help is needed

➀Push and hold [EMERGENCY] on the GM-

110DSC for 5 sec., until the short beeps become

one long beep, to send the distress call.

➁After 2182 kHz is automatically selected, transmit

the appropriate information as at left using voice.

When a potential problem exists

➀Push [SEL] on the GM-110DSC, then select “all

ships call” with [ENT] and the DATA SELECTOR.

➁Push and hold [CALL] on the GM-110DSC for 5

sec., until short beeps become one long beep, to

use the “all ships call” function.

➂After the pre-selected frequency is selected,

transmit the appropriate information using voice.

• DSC equipped ships may monitor your transmission.

Version

GMDSS

Marine

General

Ground type

Negative ground

and

Floating ground

Negative ground

and

Floating ground

Negative ground

only

Description

Corrosion-resistant exterior.

High stability crystal and FSK narrow ﬁlter built-in.

Optional DSC terminal unit can be connected.

2182 kHz 2-tone alarm is built-in.

FSK/CW narrow ﬁlter is optional.

All SSB/FSK ITU channels available.

2182 kHz 2-tone alarm is optional.

FSK/CW narrow ﬁlter is optional.

ITU channels are optional.

IC-M710RT.qxd 02.1.9 9:03 Page iii

TABLE OF CONTENTS

IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

EXPLICIT DEFINITIONS . . . . . . . . . . . . . . . . . . . . . ii

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

IN CASE OF EMERGENCY . . . . . . . . . . . . . . . . . . iii

VERSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . iv

1 OPERATING RULES AND GUIDELINES . . . . . . 1

2 PANEL DESCRIPTION . . . . . . . . . . . . . . . . . . 2–5

■Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

■Main unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

DHM-120 microphone keys . . . . . . . . . . . . . . . . . . . 4

■Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3 SELECTING A CHANNEL/FREQUENCY . . . . 6–8

■Selecting a channel . . . . . . . . . . . . . . . . . . . . . 6

DUsing the channel selector . . . . . . . . . . . . . . . . . . 6

DUsing the keypad . . . . . . . . . . . . . . . . . . . . . . . . . . 7

DScan functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

■Selecting a frequency . . . . . . . . . . . . . . . . . . . . 8

DUsing the channel selector . . . . . . . . . . . . . . . . . . 8

DUsing the keypad . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 RECEIVE AND TRANSMIT . . . . . . . . . . . . . . 9–11

■Basic voice receive and transmit . . . . . . . . . . . 9

■Functions for transmit . . . . . . . . . . . . . . . . . . . . 9

DTransmit frequency check . . . . . . . . . . . . . . . . . . . 9

DTransmit power selection . . . . . . . . . . . . . . . . . . . . 9

■Functions for receive . . . . . . . . . . . . . . . . . . . 10

DSquelch function . . . . . . . . . . . . . . . . . . . . . . . . . 10

DNoise blanker . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

DAGC off function . . . . . . . . . . . . . . . . . . . . . . . . . . 10

DRF gain setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

DClarity control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

■CW operation . . . . . . . . . . . . . . . . . . . . . . . . . 11

■FSK operation . . . . . . . . . . . . . . . . . . . . . . . . . 11

■Cross channel operation . . . . . . . . . . . . . . . . . 11

5 USER CHANNEL PROGRAMMING . . . . . . . . . 12

■Programming a frequency . . . . . . . . . . . . . . . 12

DReceive frequency . . . . . . . . . . . . . . . . . . . . . . . . 12

DTransmit frequency . . . . . . . . . . . . . . . . . . . . . . . 12

DChannel names . . . . . . . . . . . . . . . . . . . . . . . . . . 12

6 SET MODE . . . . . . . . . . . . . . . . . . . . . . . . . . 12–15

■Set mode operation . . . . . . . . . . . . . . . . . . . . 12

■Set mode contents . . . . . . . . . . . . . . . . . . . . . 12

7 CONNECTIONS AND INSTALLATION . . . . 16–25

■Supplied accessories . . . . . . . . . . . . . . . . . . . 16

■Attaching 1 remote controller . . . . . . . . . . . . . 16

■Attaching 2 remote controllers . . . . . . . . . . . . 17

DSet ID number . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

DIntercom operation . . . . . . . . . . . . . . . . . . . . . . . . 17

■Attaching 2 remote controllers and a PC . . . . 18

■Notes for remote control . . . . . . . . . . . . . . . . . 18

■Connections on rear panel . . . . . . . . . . . . . . . 19

■Connector information . . . . . . . . . . . . . . . . . . 20

■Ground connection . . . . . . . . . . . . . . . . . . . . . 22

■Power source . . . . . . . . . . . . . . . . . . . . . . . . . 22

■Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

DMN-100/MN-101L . . . . . . . . . . . . . . . . . . . . . . . . 23

DAT-130 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

DNon-Icom tuner . . . . . . . . . . . . . . . . . . . . . . . . . . 23

■Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

DMounting location . . . . . . . . . . . . . . . . . . . . . . . . . 24

DMounting example . . . . . . . . . . . . . . . . . . . . . . . . 24

DTransceiver dimensions . . . . . . . . . . . . . . . . . . . . 24

■Installing internal options . . . . . . . . . . . . . . . . 25

DOpening the case . . . . . . . . . . . . . . . . . . . . . . . . . 25

DInstalling an optional ﬁlter and alarm unit . . . . . . 25

■Fuse replacement . . . . . . . . . . . . . . . . . . . . . . 25

8 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . 26

9 SPECIFICATIONS AND OPTIONS . . . . . . . . . . 27

■Speciﬁcations . . . . . . . . . . . . . . . . . . . . . . . . . 27

■Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

IC-M710RT.qxd 02.1.9 9:03 Page iv

OPERATING RULES AND GUIDELINES

❑CALL PROCEDURES

Calls must be properly identiﬁed and time limits must

be respected.

➀Give your call sign each time you call another vessel

or coast station. If you have no call sign, identify

your vessel name and the name of the licensee.

➁Give your call sign at the end of each transmission

that lasts more than 3 min.

➂You must break and give your call sign at least once

every 15 min. during long ship-to-shore calls.

➃Keep your unanswered calls short, less than 30 sec.

Do not repeat a call for 2 min.

➄Unnecessary transmissions are not allowed.

❑PRIORITIES

➀Read all rules and regulations pertaining to priorities

and keep an up-to-date copy handy. Safety and dis-

tress calls take priority over all others.

➁False or fraudulent distress calls are prohibited and

punishable by law.

❑PRIVACY

➀Information overheard but not intended for you can-

not be lawfully used in any way.

➁Indecent or profane language is prohibited.

❑LOGS

➀All distress, emergency and safety calls must be

recorded in complete detail. Log data activity is usu-

ally recorded in 24 hour time. Universal Time (UTC)

is frequently used.

➁Adjustments, repairs, channel frequency changes

and authorized modiﬁcations affecting electrical op-

eration of the equipment must be kept in the main-

tenance log; entries must be signed by the

authorized licensed technician performing or super-

vising the work.

❑RADIO LICENSES

(1) SHIP STATION LICENSE

You must have a current radio station license before

using the transceiver. It is unlawful to operate a ship

station which is not licensed.

Inquire through your dealer or the appropriate govern-

ment agency for a Ship-Radiotelephone license appli-

cation. This government-issued license states the call

sign which is your craft’s identification for radio pur-

poses.

(2) OPERATOR’S LICENSE

A Restricted Radiotelephone Operator Permit is the li-

cense most often held by small vessel radio operators

when a radio is not required for safety purposes.

The Restricted Radiotelephone Operator Permit must

be posted or be kept with the operator. Only a licensed

radio operator may operate a transceiver.

However, non-licensed individuals may talk over a

transceiver if a licensed operator starts, supervises,

and ends the call, and makes the necessary log en-

tries.

Keep a copy of the current government rules and reg-

ulations handy.

IC-M710RT.qxd 02.1.9 9:03 Page 1

2PANEL DESCRIPTION

■Front panel (controller)

qMICROPHONE CONNECTOR (p. 20)

Accepts the supplied microphone or an optional

handset.

☞NOTE: No audio is output via the speaker when the

microphone or handset is not connected.

wPOWER SWITCH [POWER]

Turns power on and off.

eSPEAKER SWITCH [SPEAKER]

Turns the built-in speaker on and off.

•“è” appears in the display while the speaker is turned

off.

• Any external speaker connected to the rear panel is not

turned off.

rDISPLAY INTENSITY SWITCH [DIMMER]

➥Toggles the display backlight on and off.

➥While pushing, rotate [CHANNEL] to adjust the

backlighting to one of 4 levels.

➥While pushing, rotate [GROUP] to adjust the dis-

play contrast to one of 10 levels.

tVOLUME CONTROL [VOLUME]

Adjusts the audio output level.

• Audio does not come from the speaker when:

➟A microphone is not connected.

➟The [SQL] switch is turned on and no signal is being

received.

yGROUP CHANNEL SELECTOR [GROUP]

Selects groups in 20 channel steps and ITU marine

channel groups.

☞NOTE: Some versions have no ITU channels.

uANTENNA TUNE SWITCH [TUNE] (p. 9)

Tunes the connected tuner to the antenna.

• Activates only when an optional antenna tuner such as

Icom’s AT-130/E is connected.

☞NOTE: When selecting “automatic tuning” in set

mode, pushing this switch is not necessary to tune

the antenna. (p. 13)

iCHANNEL SELECTOR [CHANNEL] (p. 6)

➥Selects an operating channel within the selected

channel group such as ITU channels.

• User channels can be selected from 1 to 160 (max.)

in sequence regardless of the channel group.

➥Changes the operating frequency* after [CE] is

pushed (while “s” appears).

• The changed frequency is not programmed in this

way.

oFUNCTION SWITCH [FUNC]

After pushing, activates the secondary functions of

these switches:

[RESET] . . Deactivates external control such as

from a DSC terminal unit when con-

nected.

[SQL] . . . . . Starts and stops scan (p. 7).

[SPEAKER] Activates intercom function (p. 17).

[RX] . . . . . . Sets RF gain (p. 10).

[TX] . . . . . . Selects transmit power (p. 9).

[CE] . . . . . . Reprograms the channel name (p.

12).

☞NOTE: Function availability depends on version.

!0 CLARITY CONTROL [CLARITY] (p. 10)

Shifts the receive frequency ±150 Hz for clear re-

ception of an off frequency signal.

TUNE DUP SIMP STANDBY

DSC FSCAN

SQL N B

AGC

A43210

ALM

MICROPHONE

POWER

VOLUME

ALARM

TX FREQ

2182KHz

RESET

MODE

TUNE

MF/HF MARINE TRANSCEIVER

AGC SQL FUNC

CLARITY

SPEAKER

[ALARM] [TX FREQ]+

FOR ALARM TX

DIMMER

GROUP CHANNEL

123

456

789

RX TX

0–

CH/FREQ

iM 710

q w e r t y u i !0

!2!3!4!5 !6!7!8!9

IC-M710RT.qxd 02.1.9 9:03 Page 2

PANEL DESCRIPTION

!1 KEYPAD

➥Enters the selected channel number (or fre-

quency*) for direct channel selection. (p. 7)

➥Stores a receive frequency into a user chan-

nel or ITU simplex channel when:

•pushing [CE] (“s”appears)

•entering the desired frequency via the keypad

•pushing and holding [RX] (p. 12)

➥Adjusts the RF gain after pushing [FUNC] to

reduce the receiver sensitivity. (p. 10)

➥Stores a transmit frequency into a user chan-

nel (except General versions) when:

•pushing [TX] (“$”ﬂashes)

•pushing [CE] (“s”appears)

•entering the desired frequency via the keypad

•pushing and holding [TX] (p. 12)

➥Selects the transmitter channel for cross

channel operation (Europe versions only)

when:

•pushing [TX] (“$”ﬂashes)

•entering the desired channel number via the key-

pad

➥Selects the transmit output power after push-

ing [FUNC]. (p. 9)

➥Toggles the channel number input and fre-

quency input.* (p. 8)

•“s”appears when frequency input* is selected.

•The channel selector and keypad changes the

frequency while “s”appears.

➥Clears the entered digit and retrieves the pre-

vious channel (or frequency*) while entering

numbers. (p. 7)

➥Enters the name programming condition,

after pushing [FUNC], for changing the chan-

nel name. (p. 12)

➥Toggles the channel and frequency indica-

tions. (p. 6)

➥Enters “–” for ITU simplex channels. (p. 7)

➥Enter channel number with up to 4 or 5 digits

when “s”does not appear. (p. 7)

➥Enter the frequency with up to 6 digits* when

“” appears. (p. 8)

!2 SQUELCH SWITCH [SQL] (p. 10)

➥Activates the voice squelch function to reject un-

desired background noise while no signal is

being received.

•The squelch opens only when the received signal

contains no voice or FSK components.

➥Starts and stops the scan function after pushing

[FUNC]. (p. 7)

!3 NOISE BLANKER SWITCH [NB] (p. 10)

Turns the noise blanker function on to remove

pulse-type noise such as engine ignition noise.

•“NB”appears when the function is turned on.

–

CH/FREQ

!4 AGC OFF SWITCH [AGC] (p. 10)

Deactivates the AGC function to receive weak sig-

nals blocked by strong adjacent signals.

•“ê”appears when the [AGC] switch is turned on

(stands for AGC deactivated).

!5 MODE SWITCH [MODE] (p. 9)

Selects an operating mode temporarily. Available

modes differ with version.

•J3E (USB), H3E, J2B (AFSK), FSK, R3E and A1A (CW)

modes are available.

•The temporary mode is cleared and the previous mode

appears when changing a channel.

!6 OVEN INDICATOR (GMDSS version only)

Internal high-stability crystal oscillator unit contains

a temperature-compensating oven heater. This

high-stability crystal oscillator improves frequency

stability.

•“STANDBY”appears when power to the main unit is

turned off.

!7 TRANSMIT FREQUENCY SWITCH [TX FREQ]

(p. 9)

Displays the transmit frequency and opens the

squelch to check and monitor the transmit fre-

quency.

!8 2182 kHz SELECTION SWITCH

[2182kHz •

RESET

] (p. iii)

➥Selects channel 0 (2182 kHz; distress call fre-

quency).

•The channel selector does not function when select-

ing channel 0.

➥Ignores external control and gives the front panel

control priority when an external controller

(NMEA format) is connected.

!9 ALARM SWITCH [ALARM] (p. iii)

➥Emits a distress alarm signal from the speaker.

➥Transmits a distress alarm or alarm testing signal

when pushed together with the [TX FREQ]

switch.

☞NOTE: General versions are not equipped with this

[ALARM] switch.

*Some versions do not have frequency selection and fre-

quency indication.

IC-M710RT.qxd 02.1.9 9:03 Page 3

qRS-232C CONNECTOR (p. 18)

Connects the IC-M710RT to a PC via an RS-232C

cable for remote control of transceiver function

using the optional RS-710RT software.

wPOWER INDICATOR

Appears while power is turned on.

eCONTROLLER CONNECTOR

Connects the main body of the IC-M710RT to the

front panel (controller) when detached from the

main body.

rCONTROLLER CONNECTOR (pgs. 16, 17)

Same as above.

tPOWER SWITCH

Same function as the power switch ([POWER]) on

the front panel.

•Only available on the Europe and GMDSS versions.

2PANEL DESCRIPTION

wer

■Main unit (controller detached)

DHM-120 microphone keys

The “P”key on the HM-120

HAND MICROPHONE

can be

set to function as the [MODE], [NB], [AGC], [SQL] or

[TUNE] keys on the remote controller. (The YZ keys

function the same as the [CHANNEL] selector). Also,

using set mode (p. 15) these keys can be deactivated

if desired.

While pushing [P] on the microphone and the switch

on the remote controller whose function you want to

assign (see above), turn power ON.

•Repeat this to assign a different key.

IC-M710RT.qxd 02.1.9 9:03 Page 4

PANEL DESCRIPTION

■Display

qALARM INDICATOR (p. iii)

Appears when the alarm function is activated such

as for an alarm test or distress alarm transmission.

•Not available in General version.

wRECEIVE INDICATOR (p. 10)

Appears while receiving and when the squelch is

open.

eTUNE INDICATOR (p. 9)

Flashes while the connected antenna tuner, such as

Icom’s AT-130, is being tuned.

•Tuning starts when transmitting on a new frequency or

pushing the [TUNE] switch.

rTRANSMIT INDICATOR

➥Appears when transmitting. (p. 9)

➥Flashes when the [TX] key is pushed for transmit

frequency programming. (p. 12)

tDSC INDICATOR (p. iii)

Appears when an optional GM-110DSC

DSC TERMI

NAL UNIT

controls transceiver functions.

•The GM-110DSC can be connected to GMDSS versions

only.

yS/RF METER

➥Shows the relative received signal strength while

receiving.

➥Shows output power while transmitting.

➥Shows antenna current level when an optional

AT-130E

HF ANTENNA TUNER

is connected (Europe

versions only).

uCHANNEL/VFO INDICATOR

➥Shows the pre-programmed channel name (al-

phanumeric) during channel indication. (p. 6)

•Some versions have no channel name function and

show receive frequency instead.

➥Shows the transmit frequency during frequency

indication. (p. 6)

➥Shows transmit channel number during cross

channel operation (Europe versions only). (p. 11)

TUNE DUP SIMP

DSC FSCAN

SQL N B

AGC

A43210

ALM

yu io!0

!3!4!5!6!7

iSQUELCH INDICATOR (p. 10)

Appears when the squelch is on.

oSCAN INDICATOR (p. 7)

Appears when the scan function is in use.

•The scan function is not available on some versions.

•Pushing [FUNC] then [SQL] starts and stops scan.

!0 FUNCTION INDICATOR

Appears when the [FUNC] switch is pushed.

!1 NOISE BLANKER INDICATOR (p. 10)

Appears when the [NB] switch is turned on.

!2 AGC OFF INDICATOR (p. 10)

Appears when the [AGC] switch is pushed to indi-

cate the AGC function is deactivated.

!3 MODE READOUT

Shows the selected operating mode (type of emis-

sion).

!4 SPEAKER OFF INDICATOR

Appears when the [SPEAKER] switch is pushed to

indicate the front panel speaker is deactivated.

!5 CHANNEL READOUT

➥Shows the selected channel number during

channel indication. (p. 6)

➥Shows the receive frequency during frequency in-

dication. (p. 9)

!6 SIMPLEX/DUPLEX INDICATORS

These appear to show whether the selected chan-

nel is simplex or duplex.

!7 FREQUENCY INDICATORS (p. 8)

Appear when the frequency entry condition* is se-

lected for frequency selection.

•The [CE] key toggles the indicator ON and OFF.

* Some versions have no frequency entry condition.

IC-M710RT.qxd 02.1.9 9:03 Page 5

3SELECTING A CHANNEL/FREQUENCY

■Selecting a channel

The transceiver has 160 user channels and ITU chan-

nels. However, the number of user channels can be

optionally restricted and ITU channels are not available

with some versions.

☞NOTE: When channel 0 and/or 2182 kHz is se-

lected with the [2182KHz] switch, channel selection

is NOT possible. In such cases, push [2182KHz] in

advance.

DUP

DSC F

AGC

ALM

DUP

DSC F

AGC

ALM

DUP

DSC F

AGC

ALM

DUP

DSC F

AGC

ALM

CHANNEL INDICATION

FREQUENCY INDICATION

CHANNEL SELECTION MODE

Channel can be selected

FREQUENCY SELECTION MODE

Frequency can be changed

CH/FREQ

DUsing the channel selector

The transceiver has two large controls for group se-

lection and channel selection. The [GROUP] selector

changes channels in 20 channel increments and se-

lects ITU channel groups*; and the [CHANNEL] se-

lector selects each channel.

➀Make sure no “s”indicator appears on the display.

➁Rotate the [GROUP] selector to select the desired

channel group as shown at right and/or below.

➂Rotate the [CHANNEL] selector to select the de-

sired channel.

[EXAMPLE]: Selection with the [GROUP] selector

*All ITU channels are not available with some versions and ITU

FSK channels can be hidden using set mode. (p. 13)

1 J3E

WWV

21 J3E

KMI

41 J3E

WOM

61 J3E

WOO

121 J3E

FAX

141 J3E

SHP/SHP

401 J3E

4.357.0

4-1 J3E

4A LTD

601 J3E

6.501.0

2501 J3E

26.145.0

25-1 J3E

FAX

4001 FSK

4.210.5

ITU FSK

channels*

ITU SSB channels*

DUP

DSC F

AGC

ALM

If appears, push [CE] to delete it.

☞NOTE: Channel name (alphanumeric) may not

appear during channel indication depending on

set mode settings (p. 14).

CHANNEL GROUPS

CHANNEL NO. DESCRIPTION

1 to 160 User channels*1

401 to 427 4 MHz ITU duplex channels

4-1 to 4-9 4 MHz ITU simplex channels

601 to 608 6 MHz ITU duplex channels

6-1 to 6-9 6 MHz ITU simplex channels

801 to 832 8 MHz ITU duplex channels

8-1 to 8-9 8 MHz ITU simplex channels

1201 to 1241 12 MHz ITU duplex channels

12-1 to 12-9 12 MHz ITU simplex channels

CHANNEL NO. DESCRIPTION

1601to 1656 16 MHz ITU duplex channels

16-1 to 16-9 16 MHz ITU simplex channels

1801 to 1815 18 MHz ITU duplex channels

18-1 to 18-9 18 MHz ITU simplex channels

2201 to 2253 22 MHz ITU duplex channels

22-1 to 22-9 22 MHz ITU simplex channels

2501 to 2510 25 MHz ITU duplex channels

25-1 to 25-9 25 MHz ITU simplex channels

4001 to 25040 ITU FSK duplex channels*2

*1[GROUP] selector changes in 20 channels steps.

*2SITOR use—no group separation.

IC-M710RT.qxd 02.1.9 9:03 Page 6

Andere Handbücher für IC-M710RT

Inhaltsverzeichnis

Andere Icom Transceiver Handbücher

Icom

Icom IC-F14/S Bedienungsanleitung

Icom

Icom IC-M73 Bedienungsanleitung

Icom

Icom IC-F1721 Bedienungsanleitung

Icom

Icom IC-F9511 Bedienungsanleitung

Icom

Icom IC-M603 Bedienungsanleitung

Icom

Icom IC-F1000 series Bedienungsanleitung

Icom

Icom IC-7100 Bedienungsanleitung

Icom

Icom IC-M59euro Bedienungsanleitung

Icom

Icom IC-F22SR Bedienungsanleitung

Icom

Icom IC-F4022T Bedienungsanleitung

Icom

Icom IC-A24E Bedienungsanleitung

Icom

Icom IC-4AT Bedienungsanleitung

Icom

Icom IC-F8101 Bedienungsanleitung

Icom

Icom M506 31 Bedienungsanleitung

Icom

Icom IC-T7A Bedienungsanleitung

Icom

Icom IC-04A Bedienungsanleitung

Icom

Icom IC-W2A Bedienungsanleitung

Icom

Icom IC-A210 Bedienungsanleitung

Icom

Icom IC-M421 Bedienungsanleitung

Icom

Icom IC-M72 Bedienungsanleitung

Icom

Icom IC-F30GT Bedienungsanleitung

Icom

Icom IC-F110 Bedienungsanleitung

Icom

Icom IC-V201 Bedienungsanleitung

Icom

Icom IC-F30GT Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung