Icom IC-V10MR Bedienungsanleitung

OPERATING GUIDE

VHF TRANSCEIVER

IC-V10MR

We appreciate you choosing Icom for your communication

needs.

The MDC 1200 signaling system is built into your

IC-V10MR transceiver.

READ ALL INSTRUCTIONS carefully and completely

before using the transceiver.

SAVE THIS OPERATING GUIDE — This operating

guide contains important operating instructions for:

•IC-V10MR TRANSCEIVER

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-

porated (Japan) in Japan, the United States, the United Kingdom, Germany,

France, Spain, Russia and/or other countries.

All other products or brands are registered trademarks or trademarks of their

respective holders.

IMPORTANT

TABLE OF CONTENTS

IMPORTANT.......................................................................... i

TABLE OF CONTENTS........................................................ ii

1 PANEL DESCRIPTION................................................1–5

■Front, top and side panels............................................1

■

LED indicator................................................................3

■Programmable function keys ........................................4

2 BASIC OPERATION...................................................6-13

■Channel selection.........................................................6

■Receiving and transmitting...........................................6

■Emergency Call............................................................8

■Lone Worker Emergency Call.......................................9

■Man Down Emergency Call..........................................9

■Motion Detection Emergency Call................................9

■User set mode............................................................10

■Setting the microphone gain ......................................10

■Setting the squelch level ............................................11

■Setting the Beep function and level............................12

■Setting the Ringer level ..............................................13

3 MDC 1200 SYSTEM OPERATION..........................14–15

■MDC 1200 system operation......................................14

■Receiving a call ..........................................................14

■Transmitting a call.......................................................15

■Front, top and side panels

q ROTARY SELECTOR

Rotate to select the preset memory channels.➥

w VOLUME CONTROL [VOL]

Rotate to turn the power ON or OFF and to adjust the➥

audio level.

eDEALER-ASSIGNABLE KEY [Emer]

A desired function can be programmed by your dealer.➥

1PANEL DESCRIPTION

w VOLUME

CONTROL [VOL]

e [Emer]

Speaker

r SPEAKER-

MICROPHONE

JACK

Microphone

yPTT

iANTENNA

SWITCH

[PTT]

LED

INDICATOR

CONNECTOR

[Upper]

[Lower]

q ROTARY

SELECTOR

PANEL DESCRIPTION

rSPEAKER-MICROPHONE JACK

Connect optional equipment.➥

NOTE: After turning OFF the transceiver, connect or dis-

connect the optional equipment.

tDEALER-ASSIGNABLE KEYS

yPTT SWITCH [PTT]

[Upper], [Lower]

➥Desired functions can be independently programmed

by your dealer.

i ANTENNA CONNECTOR

Hold down to transmit, release to receive.➥

LED INDICATOR

Lights red while transmitting.➥

Lights green while receiving a signal, or when the➥

squelch is open.

➥Lights or blinks orange when the matched 2-Tone

is received, depending on the presetting.

➥You should charge the battery when the indicator slow-

ly blinks.

You must charge the battery when the indicator blinks➥

fast.

Connects the supplied antenna.➥

Jack cover

NOTE: Attach the jack cover when

optional equipment is not used.

PANEL DESCRIPTION

■LED indicator

The LED indicator indicates the status of various parameters of

the transceiver as follows:

(Reference: R=Red, G=Green, O=Orange)

G G

R O G R O G

OOOOOO

OOOO

OOOR

GROGROGROGRO

G G G G

• Receiving

• Low Battery 2 (You must charge the battery.)

• Low Battery 1 (You should charge the battery.)

• When turning ON the power

• Calling

• Audible

• Lockout, TX Inh, TOT (when transmit is inhibited)

• Successful

• Failed, Error

• Emergency, Siren

G GGGG GGG

R G R G R G R G R G R G R G R G

R O R O R O R O R O R O R O R O

R R R R

R R

• Cloning (reading or writing data)

• Cloning Error (if cloning fails)

• Inh, Blank CH, Unlocked (when you cannot use the channel)

• TX Low Battery 2 (while transmitting)

• TX Low Battery 1 (while transmitting)

• Transmitting

• Call LED=ON (when receiving a matched 2-Tone or 5-Tone)

• Call LED=Blink (when receiving a matched 2-Tone or 5-Tone)

• Scanning

PANEL DESCRIPTION

TX Low BATT2

Clone Err

Clone TX/RX

Low BATT1

Low BATT2

Busy

F/S Scan

Call LED Blink

Call LED ON

TX Low BATT1

Clone

G GGGG GGG

R G R G R G R G R G R G R G R G

R O R O R O R O R O R O R O R O

R R R R

R R

G G

TX Low BATT2

Clone Err

Clone TX/RX

Low BATT1

Low BATT2

Busy

F/S Scan

Call LED Blink

Call LED ON

TX Low BATT1

Clone

G G

R O G R O G

OOOOOO

OOOO

OOOR

O G

O R

OOOOGR RGGRGR

G G G G

■Programmable function keys

The following functions can be assigned to [Emer], [Upper],

[Lower], and [Ext. Emer].

Consult your Icom dealer or system operator for details con-

cerning your transceiver’s programming.

SCAN START/STOP

➥Push to start and cancel a scan.

•

When a scan is started with the Power ON Scan or Auto-

matic scan function, push this key to cancel it. The can-

celled scan resumes after a set time period.

PRIORITY A CHANNEL, PRIORITY B CHANNEL

➥Push to select the Priority A or Priority B channel.

PRIORITY A CHANNEL (REWRITE),

PRIORITY B CHANNEL (REWRITE)

➥Push to select the Priority A or Priority B channel.

➥Hold down [Prio A (Rewrite)] or [Prio B (Rewrite)] to assign

the operating channel to Priority A or Priority B channel,

respectively.

MEMORY CHANNELS 1, 2, 3, 4

➥Push to directly select memory channel 1, 2, 3 or 4, if pro-

grammed.

MONI

➥Hold down to cancel the CTCSS (DTCS) or 2-Tone mute.

The transceiver enters “Audible” mode.

➥Push to turn OFF the function.

LOCK

➥Hold down this key to lock all programmable keys except

the followings:

[Moni], [Lock], [Emer], [Surveillance], [Siren], [Lone

Worker], and [Shift].

LONE WORKER

➥Hold down to turn ON the Lone Worker

Function. ➥Push to turn OFF the Function.

HIGH/LOW

➥Push to select the transmit output power temporarily or

permanently, depending on the presetting.

PANEL DESCRIPTION

TALK AROUND

➥Push to turn the Talk Around function ON or OFF.

• The Talk Around function equalizes the transmit frequen-

cy to the receive frequency for transceiver-to-transceiver

communication.

DTMF AUTODIAL

➥Push to transmit the preprogrammed DTMF code.

CALL

➥Push to transmit a 2-Tone in the operating chan nel.

CALL A (CODE 1)/CODE B (CODE 2)

➥Push to transmit a 2-Tone, that is programmed in

channel 1 (Code A) or channel 2 (Code B).

EMERGENCY

➥Hold down during the Emer SW ON timer period to turn

ON the Emergency function.

• After the Start or Repeat timer period ends, an Emer-

gency call is automatically transmitted once, or repeat-

edly, depending on the

presetting

➥Hold down during the Emer SW OFF timer period to can-

cel the Emergency function, before transmitting an Emer-

gency call.

SURVEILLANCE

➥Hold down to turn ON the Surveillance function.

➥Push to turn OFF the function.

• When this function is ON and a signal is received, a

beep does not sound and the LED does not light, even if

you push any key.

SIREN

➥Hold down to emit a siren sound.

• This function may use for situations other than an emer-

gency alert, such as a security alarm.

➥Turning OFF the transceiver power to stop the siren

sound.

COMPANDER

➥Hold down to turn ON the Compander function.

➥Push to turn OFF the function.

•

The Compander function reduces noise components from

the transmitted audio to provide clear communication.

ANNOUNCE

➥Push to turn the Channel Announce function ON or OFF.

BASIC OPERATION 2

■Channel selection

There are several types of channel selections. Methods may

differ, depending on the presetting. Consult your dealer for

details.

To select the desired operating channel:

➥Rotate [ROTARY SELECTOR].

➥Push one of [MR-CH 1] to [MR-CH 4].

➥Push [Prio A], [Prio B], [Prio A (Rewrite)] or [Prio B

(Rewrite)].

AUTOMATIC SCAN TYPE:

Channel setting is not necessary for this scan type. When

turning ON the power, the transceiver automatically starts

scanning. Scanning stops when a signal is received.

■Receiving and transmitting

CAUTION:

Attach an antenna before transmitting.

Transmitting without an antenna may damage the trans-

ceiver.

Receiving:

Rotateq[VOL] to turn ON the power.

Rotatew[ROTARY SELECTOR], or push one of the memo-

ry channel keys, [MR-CH1] to [MR-CH4], to select a chan-

nel.

e When receiving a call, adjust the audio output level to a

comfortable listening level.

Transmitting:

Wait until the channel is clear to avoid interference.

While holding downq[PTT], speak at a normal voice level.

Releasew[PTT] to receive.

IMPORTANT: To maximize the readability of your signal:

1. After pushing [PTT], pause brieﬂy before you start

speaking.

2. Hold the microphone 5 to 10 cm (2 to 4 inches) from

your mouth, then speak at a normal voice level.

BASIC OPERATION

Transmitting notesD

Transmit inhibit function•

The transceiver has several inhibit functions which restrict

transmission under the following conditions:

- The channel is busy.

However, depending on the presettings, you can transmit

when the call includes an unmatched (or matched) CTC-

SS (DTCS) tone.

- The selected channel is a ‘receive only’ channel.

Time-out timer•

If continuous transmission exceeds the preprogrammed

time-out timer limit, transmission is cut off.

Penalty timer•

The time-out timer cuts off transmission, further transmis-

sion is inhibited for the preprogrammed penalty timer peri-

od.

DReceiving a Stun, Kill and Revive call

The dispatcher can send a 2-Tone that will stun, kill or revive

your transceiver.

When the Stun call is received, beeps sound*, and you can-

not receive or transmit. Receiving a Revive call, or entering a

password*, is necessary to operate the transceiver again.

When the Kill call is received, beeps sound*, and the trans-

ceiver becomes unusable. Cloning the transceiver is neces-

sary to operate the transceiver again, in this case.

* Depending on the presetting. Ask your dealer for details.

Inhaltsverzeichnis

Andere Icom Transceiver Handbücher

Icom

Icom IC-M23 Bedienungsanleitung

Icom

Icom D-STAR ID-31A; D-STAR ID-31E Bedienungsanleitung

Icom

Icom IC-V85 Bedienungsanleitung

Icom

Icom IC-245 Bedienungsanleitung

Icom

Icom iF110 Bedienungsanleitung

Icom

Icom IC-M423 Bedienungsanleitung

Icom

Icom IC-T3H Bedienungsanleitung

Icom

Icom IC-E7 Bedienungsanleitung

Icom

Icom IC-M200 Bedienungsanleitung

Icom

Icom IC-455 Bedienungsanleitung

Icom

Icom IC-M35 Bedienungsanleitung

Icom

Icom IC-02A Bedienungsanleitung

Icom

Icom VHF MARINE TRANSCEIVER IC-M501EURO Bedienungsanleitung

Icom

Icom IC-M802 Bedienungsanleitung

Icom

Icom iC-F5012 Bedienungsanleitung

Icom

Icom IC-756 Bedienungsanleitung

Icom

Icom IC-A3 Bedienungsanleitung

Icom

Icom IC-7300 Bedienungsanleitung

Icom

Icom IC-M2A Bedienungsanleitung

Icom

Icom IC-W21A Bedienungsanleitung

Icom

Icom IC-91AD Bedienungsanleitung

Icom

Icom IC-2100H Bedienungsanleitung

Icom

Icom IC-4088A Bedienungsanleitung

Icom

Icom IC-A210E Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung