Icom ID-5100E Bedienungsanleitung

S-15103XZ-C1

June 2014

DUAL BAND TRANSCEIVER

This service manual describes the latest technical informa-

tion for the ID-5100A and ID-5100E DUAL BAND TRANSCEIVER, at

the time of publication.

NEVER connect the transceiver to an AC outlet or to a DC

power supply that uses more than the speciﬁed voltage. This

will ruin the transceiver.

DO NOT expose the transceiver to rain, snow or liquids.

DO NOT reverse the polarities of the power supply when con-

necting the transceiver.

DO NOT apply an RF signal of more than 20 dBm (100 mW) to

the antenna connector. This could damage the transceiver’s

front-end.

To upgrade quality, any electrical or mechanical parts

and internal circuits are subject to change without notice

or obligation.

MODEL VERSION TX OUTPUT

POWER

ID-5100A

TPE 25 W

USA

50 W

KOR

EXP

ID-5100E EUR

ITR

Be sure to include the following four points when ordering

replacement parts:

1. 10-digit Icom part number

2. Component name

3. Equipment model name and unit name

4. Quantity required

1110003491 S.IC TA31136FNG ID-5100A MAIN UNIT 5 pieces

8820001210 Screw 2438 screw ID-5100A Top cover 10 pieces

Addresses are provided on the inside back cover for your

convenience.

ORDERING PARTS

1. Make sure that the problem is internal before dis-assem-

bling the transceiver.

2. DO NOT open the transceiver until the transceiver is dis-

connected from its power source.

3. DO NOT force any of the variable components. Turn them

slowly and smoothly.

4. DO NOT short any circuits or electronic parts. An insulated

tuning tool MUST be used for all adjustments.

5. DO NOT keep power ON for a long time when the trans-

ceiver is defective.

6. DO NOT transmit power into a Standard Signal Generator

or a Sweep Generator, otherwise the RF power may dam-

age them.

7. ALWAYS connect a 50 dB to 60 dB attenuator between the

transceiver and a Deviation Meter or Spectrum Analyzer,

when using such test equipment.

8. READ the instructions of the test equipment thoroughly

before connecting it to the transceiver.

REPAIR NOTES

INTRODUCTION CAUTION

(ID-5100A)

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the

United Kingdom, Germany, France, Spain, Russia and/or other countries.

TABLE OF CONTENTS

SECTION 1 SPECIFICATIONS

SECTION 2 INSIDE VIEWS

SECTION 3 DISASSEMBLY INSTRUCTION

SECTION 4 CIRCUIT DESCRIPITON

4-1 RECEIVER CIRCUITS...................................................................................... 4-1

4-2 TRANSMITTER CIRCUITS............................................................................... 4-3

4-3 FREQUENCY SYNTHESIZER CIRCUITS ....................................................... 4-5

4-4 VOLTAGE BLOCK DIAGRAM ........................................................................... 4-6

4-5 PORT ALLOCATIONS ...................................................................................... 4-6

SECTION 5 ADJUSTMENT PROCEDURES

5-1 PREPARATION ................................................................................................. 5-1

5-2 FREQUENCY ADJUSTMENT .......................................................................... 5-2

5-3 TRANSMIT ADJUSTMENTS ............................................................................ 5-3

5-4 RECEIVE ADJUSTMENTS............................................................................... 5-5

SECTION 6 PARTS LIST

SECTION 7 MECHANICAL PARTS

SECTION 8 BOARD LAYOUTS

SECTION 9 BLOCK DIAGRAM

SECTION 10 VOLTAGE DIAGRAM

1-1

SECTION 1

SPECIFICATIONS

General

■

• Frequency coverage:

EUR RX 118–174 MHz*1, 375–550 MHz*2

TX 144–146 MHz, 430–440 MHz

ITR RX 118–136.99166 MHz*3, 144–146 MHz, 430–434 MHz, 435–438 MHz

TX 144–146 MHz, 430–434 MHz, 435–438 MHz

TPE RX 144–146 MHz, 430–432 MHz

TX 144–146 MHz, 430–432 MHz

USA RX 118–174 MHz*4, 375–550 MHz*5

TX 144–148 MHz, 430–450 MHz*5

KOR RX 144–146 MHz, 430–440 MHz

TX 144–146 MHz, 430–440 MHz

EXP RX 118–174 MHz*4, 375–550 MHz*2

TX 137–174 MHz*4, 400–470 MHz*2

Guaranteed only 144–146 MHz, *

Guaranteed only 430–440 MHz,

*3 Not guaranteed,

Guaranteed only 144–148 MHz, *

Guaranteed only 440–450 MHz

• Mode: F2D/F3E (FM/FM-N), F7W (DV), A3E (AM/AM-N) RX only

• Number of memory channels: 1000 channels

• Number of program scan channels: 25 channels

(2 edge frequencies in each channel)

• Number of call channels: 4 channels (2 channels × 2 bands)

• Antenna connector: SO-239

• Antenna impedance: 50 ø

• Usable temperature range: –10˚C to +60˚C; +14˚F to +140˚F

• Frequency stability: ±2.5 ppm (–10˚C to +60˚C; +14˚F to +140˚F)

•

Digital transmission speed

: 4.8 kbps

• Voice coding speed: 2.4 kbps

• Frequency resolution: 5 kHz, 6.25 kHz, 8.33 kHz, 10 kHz, 12.5 kHz, 15 kHz, 20 kHz, 25 kHz, 30 kHz, 50 kHz

(The 8.33 kHz step is selectable only when the VHF air band is selected.)

• Power supply: 13.8 V DC ±15% (negative ground)

• Current drain:

Transmit

Maximum current drain: 10.5 A (TPE version)

13.0 A (Other versions)

Receive

Standby: 1.2 A

Maximum audio: 1.8 A

• Dimensions (projections not included):

Main unit: 150(W) 40(H) 172.6(D) mm; 5.9(W) 1.6(H) 6.8(D) inch

Controller:

182.2(W) 24.8(H) 81.5(D) mm;

7.2(W) 1.0(H) 3.2(D) inch

• Weight (approximately):

Main unit: 1.3 kg; 2.9 lb

Controller: 260 g; 9.2 oz

1-2

Transmitter

■

• Modulation system:

FM/FM-N Variable reactance frequency modulation

DV GMSK reactance frequency modulation

• Maximum Deviation:

FM ±5.0 kHz

FM-N ±2.5 kHz

• Microphone impedance: 600 ø

• Spurious emission: –60 dBc

• Output power: High 25 W, Mid 15 W, Low 5 W (TPE version)

High 50 W, Mid 15 W, Low 5 W (Other versions)

Receiver

■

• Receive system: Double superheterodyne system

• IF frequencies:

Band A 1st IF 38.85 MHz

2nd IF 450 kHz

Band B 1st IF 46.35 MHz

2nd IF 450 kHz

• Sensitivity (except spurious points)

Amateur bands

FM/FM-N (12 dB SINAD)

0.18 µV

DV (BER 1%) 0.28 µV

Except Amateur bands

FM/FM-N (12 dB SINAD)

0.32 µV (137.000 to 159.995 MHz)

0.56 µV (160.000 to 174.000 MHz)

0.56 µV (375.000 to 399.995 MHz)

0.32 µV (400.000 to 499.995 MHz)

0.56 µV (500.000 to 550.000 MHz)

AM (10 dB S/N) 1 µV (118.000 to 136.99166 MHz)

• Squelch sensitivity: 0.13 µV (Threshold)

• Selectivity:

FM 60 dB

FM-N 55 dB

DV 50 dB

• Spurious and image rejection ratio:

60 dB

55 dB (A band UHF)

• AF output power: 2.0 W (at 10% distortion with an 8 øload)

• AF output impedance: 8 ø

All stated speciﬁcations are typical and subject to change without notice or obligation.

2-1

SECTION 2

INSIDE VIEWS

IC7

IC8

C80

IC2

IC5

IC6

• CONTROL UNIT

(TOP VIEW)

• CONTROL UNIT

(BOTTOM VIEW)

3.3 V REGULATOR

(IC7)

3.3 V REGULATOR

(IC6)

RESET IC

(IC5)

CPU CLOCK

(X1)

TOUCH SCREEN CONTROLLER

(IC8)

CONTROLLER CPU

(IC2)

2-2

FI104

FI105

IC1

IC3

IC4

IC100

IC101

IC102

IC103

IC104

IC107

IC108

IC109

IC110

IC111

IC112

IC113

IC117

IC120

IC121

IC122

IC123

IC124

IC125

IC202

IC203

IC205

IC207

IC208

IC301

IC302

IC307

IC308

IC312

IC314

IC315

IC316

IC317

IC318

IC319

IC320

IC323

IC324

IC400

IC403

IC404

IC405

IC406

IC407

X301

X400

LO AMP & LO SW

(Band B)

• MAIN UNIT

(TOP VIEW)

DSP

(IC400)

VOLTAGE DETECTOR

(IC324)

AF SW

(IC205)

IF IC (Band A)

(IC121)

AF SW

(IC100)

AF SW

(IC104) AUDIO SIGNAL PROCESSOR

(IC103)

EXPANDER

(IC316)

AF SW

(IC109)

5 V REGULATOR

(IC319)

ELECTRIC VOLUME IC

(IC110)

AF LPF & HPF

(IC407)

EEPROM

(IC301)

RTC BACKUP BATTERY

(IC301)

REAL TIME CLOCK (RTC) IC

(IC302)

RS232 LEVEL CONVERTER

(IC318)

AF SW

(IC111)

AF BUFFER

(IC117)

AF SW

(IC113)

AF LPF & HPF

(IC406)

DSP CLOCK

(X400)

D/A CONVERTER

(IC1)

EXPANDER

(IC317)

1ST MIXER

(Band A)

EXPANDER

(IC315)

IF IC (Band B)

(IC120)

1ST IF FILTER (Band B)

(FI104)

1ST IF FILTER (Band A)

(FI105)

VCO

(Band B)

VCO

(Band A)

1ST MIXER

(Band B)

LO AMP & LO SW

(Band A)

2-3

• MAIN UNIT

(BOTTOM VIEW)

2ND IF FILTER (Band A)

(FI100)

MAIN CPU CLOCK

(X300)

DSP FLASH ROM

(IC401)

SUB CPU CLOCK

(X302)

AF POWER AMP

(IC106)

AF POWER AMP

(IC105)

6 V SWITCHING REGULATOR

(IC309)

PLL IC (Band B)

(IC206)

AF SW

(IC119)

REFERENCE FREQUENCY

OSCILLATOR (Band B)

(X201)

APC AMP

(IC2)

DISCRIMINATOR (Band A)

(X101)

2ND IF FILTER (Band A)

(FI101)

SRAM

(IC304)

8 V REGULATOR

(IC321)

8 V REGULATOR

(IC313)

MAIN CPU

(IC300)

3.3 V REGULATOR

(IC311)

LINER CODEC

(IC402)

SUB CPU

(IC303)

3.3 V REGULATOR

(IC306)

3.3 V REGULATOR

(IC305)

QUAD BUS BUFFER

(IC200)

PLL IC (Band A)

(IC201)

REFERENCE FREQUENCY OSCILLATOR (Band A)

(X200)

2ND IF FILTER (Band A)

(FI102) 2ND IF FILTER (Band A)

(FI103)

DISCRIMINATOR (Band A)

(X102)

CURRENT DETECTOR

(IC310)

3-1

SECTION 3

DISASSEMBLY INSTRUCTION

Removing the CONTROL UNIT from the controller.

1) Remove two dials and four knobs from the front

panel.

2) Remove four screws from the rear panel.

BE CAREFUL when you disassemble the rear panel from

the CONTROL UNIT. Otherwise the flat cable and the

connector may be cut.

Knob

Dial

Flat cable

Four screws

Flat cable

Rear panel

CONTROL UNIT

Flat cable

flat cable

Release the locks

Pull straight

FLAT CABLE

Flat cable

BE CAREFUL about the locks.

Four screws

CONTROL UNIT

FRONT PANEL

Flat cable

flat cable

Release the locks

Pull straight

FLAT CABLE

Flat cable

BE CAREFUL about the locks.

3) Take off the rear panel carefully in the direction of

the arrow, and then disconnect the ﬂat cable.

4) Disconnect two ﬂat cables.

5) Remove four screws from the CONTROL UNIT.

6) Remove the CONTROL UNIT from the front panel.

(Continued on the right above.)

3-2

1) Remove eight screws from the top cover.

2) Remove the clip and disconnect the speaker cable.

3) Remove eight screws from the bottom cover.

Bottom cover

Eight screws

Flat cable

Speaker

Clip

Flat cable

SPEAKER

CABLE

Bottom cover

Eight screws

Flat cable

14 screws

Flat cable

FAN

CABLE

UNSOLDER

Solder

remover

Flat cable

MAIN UNIT

4) Remove total of 14 screws from the MAIN UNIT.

5) Disconnect the cooling fan cable, and unsolder ﬁve

points (at the antenna connector and the DC cable).

6) Remove the MAIN UNIT from the chassis in the di-

rection of the arrow.

(Continued on the right above.)

Before disassembling:

REMOVE the SD card if inserted. Otherwise the MAIN

UNIT and chassis cannot be separated.

M Removing the MAIN UNIT from the chassis.

Andere Handbücher für ID-5100E

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Icom Transceiver Handbücher

Icom

Icom IC-F3161 Series Bedienungsanleitung

Icom

Icom IC-726 Bedienungsanleitung

Icom

Icom iM400BB Bedienungsanleitung

Icom

Icom IC-M422 Bedienungsanleitung

Icom

Icom IC-M304 Bedienungsanleitung

Icom

Icom VHF IC-F50 Bedienungsanleitung

Icom

Icom IC-F6013H Bedienungsanleitung

Icom

Icom IC-410PRO Installationsanleitung

Icom

Icom IC-22U Bedienungsanleitung

Icom

Icom IC-F5220D Bedienungsanleitung

Icom

Icom IC-F1000 series Bedienungsanleitung

Icom

Icom IC-706MKII Bedienungsanleitung

Icom

Icom IC-M91D Bedienungsanleitung

Icom

Icom IC-27A Bedienungsanleitung

Icom

Icom IC-M810 Bedienungsanleitung

Icom

Icom IC-2725E Bedienungsanleitung

Icom

Icom Ic-V88 Bedienungsanleitung

Icom

Icom IDAS F3201DEX 14 Bedienungsanleitung

Icom

Icom IC-F14 Bedienungsanleitung

Icom

Icom IC-2000 Bedienungsanleitung

Icom

Icom IF3061S Bedienungsanleitung

Icom

Icom IC-F6061 Bedienungsanleitung

Icom

Icom IC-207H Bedienungsanleitung

Icom

Icom IC-T2H Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung