Icom IFC-30LT Bedienungsanleitung
ICOM IFC-30LT
Article Code
PCOMTRVH30-
VHF HANDSET
TECHNICAL SPECIFICATIONS ....................................................3
FRONT PANEL .....................................................................4
SIDE VIEW ........................................................................5
TOP VIEW .........................................................................6
BASIC SETTINGS ...................................................................7
SETTING THE DISPLAY BRIGHTNESS .........................................7
SETTING OF SQUELCH AND MINIMUM VOLUME LEVEL ....................8
ACTIVATING BEEPS ..............................................................9
KEYPAD SETTINGS IN SETMODE ............................................ 10
TO ENTER SET MODE.......................................................... 11
PROGRAMMING TX AND RX FREQUENCIES ON A CHANNEL ............. 12
PROGRAMMING CTCSS CODES IN TX AND RX ON A CHANNEL.......... 15
PROGRAMMING THE SCAN FUNCTION ...................................... 19
PROGRAMMING THE OUTPUT POWER OF A CHANNEL..................... 22
PROGRAMMING THE « TIME OUT TIMER » (TOT) PER CHANNEL........ 24
PROGRAMMING VIA SOFTWARE.............................................. 26
CLONING TWO TRANSCEIVERS .............................................. 28
Guideline Télécom MSFB Technical Sheets ICOM IC-F30 LT 05/08/2002
2
3
ICOM IFC-30LT
TECHNICAL SPECIFICATIONS
FREQUENCY RANGE :
IC-F30LT 146 – 174 MHz
IC-F40LT 425 – 470 MHz
CHANNEL CAPACITY :
IC-F30LT IC-F40LT 99
channels
CHANNEL SPACING: 12.5 KHz / 20 KHz / 25 KHz
OPERATING TEMPERATURE RANGE : from – 30° to + 55°
OUTPUT POWER : HIGH (H) 5 Watts
LOW (LO1) 3 Watts
LOW (LO2) 1 Watt
CONSUMPTION : Reception / Std By : 0,450 A
Transmission : 2,5 A
BATTERY VOLTAGE :
CM-140 : 7,2 Volts / 1,4 A
Guideline Télécom MSFB Technical Sheets ICOM IC-F30 LT 05/08/2002
FRONT PANEL
123
456
789
*
0
#
Po
P1
P2
ICOM
VHF TRANSCEIVER
IC-F30LT
1
2
3
4
5
6
7
8
10
9
1. ANTENNA: never transmit without
antenna
2. PROGRAMMABLE BUTTON
3. PROGRAMMABLE BUTTON
4. PUSH TO TALK : press to transmit,
release to receive
5. LOUDSPEAKER AND MICROPHONE
6. KEYPAD : used to enter DTMF
codes, change channel or « bank »
depending on settings.
7. DISPLAY
8. VOLUME ON/OFF : allows turning
handset on or off and adjusting
volume level.
9. LED :
- Red during transmission
- Green during reception
- Orange during DTMF
reception
- Blinking red when battery is
low
10. CHANNEL SELECTOR
Guideline Télécom MSFB Technical Sheets ICOM IC-F30 LT 05/08/2002
4
SIDE VIEW
1
2
3
4
1. PUSH TO TALK :
PRESS TO SPEAK,
RELEASE TO LISTEN
2. DISPLAY LIGHT
CONTROL
3. PROGRAMMING
BUTTON
4. BATTERY PACK
Guideline Télécom MSFB Technical Sheets ICOM IC-F30 LT 05/08/2002
5
TOP VIEW
1
3
6
8
10
12
14
16
1
2
3
4
5
1. ANTENNA SOCKET
2. ACCESSORIES SOCKET: External microphone
EM-81 or cloning cable OPC-
444. NOTE : never use the transceiver with the socket cover removed. Dust and
other foreign material can damage the transceiver.
3. VOLUME ON/OFF :
allows to turn transceiver on or off and to adjust volume
level.
4.
CHANNEL SELECTOR
5.
PROGRAMMABLE BUTTON (RED) : Pressing this button for longer than
2
seconds locks the keypad, a key symbol is displayed. To unlock, press again for more
than 2 seconds.
Guideline Télécom MSFB Technical Sheets ICOM IC-F30 LT 05/08/2002
6
7
BASIC SETTINGS
SETTING THE DISPLAY BRIGHTNESS
The display can be lit in three different ways :
- Always OFF
- On for 5 seconds when a button is pressed.
- Always ON.
NOTE: Always choose position 2 (light on for 5 sec) to save the battery.
SEQUENCE ACTION
1 TRANSCEIVER OFF
2 PRESS SIMULTANEOUSLY ON
AND
PTT
AND TURN TRANSCEIVER ON
3
PRESS ON RED BUTTON
ONCE OR A NUMBER OF TIMES
TO SELECT THE REQUIRED POSSIBILITY
4 1 SHORT « BEEP » : LIGHTING ALWAYS OFF
5 STANDARD
SETTING
2 SHORT « BEEPS » : LIGHTING ACTIVATED FOR 5 SECONDS WHEN
A BUTTON IS PRESSED
6 1 LONG « BEEP » : LIGHTING ALWAYS ON
7 TURN TRANSCEIVER OFF
Guideline Télécom MSFB Technical Sheets ICOM IC-F30 LT 05/08/2002
SETTING OF SQUELCH AND MINIMUM VOLUME LEVEL
This function allows to :
- Set the minimum volume level when the Volume knob is turned at its lowest
position. For example, in a noisy environment, you might need to increase the
minimum volume level.
- Set the background noise cut off level (Squelch).
Note : To avoid interferences, step away from electrical equipment like engines, computers
or other sources of parasites while doing these settings.
SEQUENCE ACTION
1 TRANSCEIVER OFF
2 PRESS SIMULTANEOUSLY ON
PTT
AND
AND TURN
TRANSCEIVER ON
3 SELECT ONE CHANNEL WHICH DOES NOT HAVE A CTCSS
PROGRAMMED ON IT
4 SETTING THE BACKGROUND NOISE CUT OFF LEVEL (SQUELCH)
PRESS
AND SIMULTANEOUSLY, TURN THE
VOLUME KNOB FROM CLOCKWISE UNTIL THE
BACKGROUND NOISE STARTS. RETURN
COUNTERCLOCKWISE TO WHEN THE NOISE JUST STOPS
(CUT OFF LEVEL).
5 SETTING THE MINIMUM VOLUME LEVEL PRESS
AND SIMULTANEOUSLY, TURN THE VOLUME KNOB TO
THE REQUIRED LEVEL
6 IF YOU HAVE MODIFIED THE MINIMUM VOLUME LEVEL, YOU
WILL HAVE TO SET THE SQUELCH LEVEL AGAIN
Guideline Télécom MSFB Technical Sheets ICOM IC-F30 LT 05/08/2002
8
7 TURN TRANSCEIVER OFF
ACTIVATING BEEPS
This setting allows :
- To enable or disable the BEEPS when buttons on the transceiver are pressed.
- To link the sound level of the BEEPS to the general volume setting of the
transceiver.
SEQUENCE ACTION
1 TRANSCEIVER OFF
2 PRESS SIMULTANEOUSLY ON
AND TURN TRANSCEIVER ON
3
PRESS
- 1 SHORT BEEP ÖBEEP OFF
- 2 SHORT BEEPS ÖBEEP ON
4 PRESS
-
1 SHORT BEEP ÖLEVEL OF BEEP IS LINKED TO THE VOLUME
- 2 SHORT BEEPS ÖLEVEL OF BEEP IS NOT LINKED TO VOLUME
AND IS SET AS EXPLAINED BELOW
Guideline Télécom MSFB Technical Sheets ICOM IC-F30 LT 05/08/2002
9
5 SETTING OF BEEP SOUND LEVEL ( 2 methods)
PRESS
AND SET SOUND LEVEL WITH VOLUME KNOB
OR
WITH EACH PRESS ON
THE SOUND LEVEL INCREASES
6 TURN TRANSCEIVER OFF
KEYPAD SETTINGS IN SETMODE
The SET MODE function enables the following settings :
- The TOT (Time Out Timer) function per channel
- The SCAN function
- The TEXT function (to name a channel)
- The reception frequency RX per channel
- The transmission frequency TX per channel
- The CTCSS code in reception per channel
- The CTCSS code in transmission per channel
- Priority A and B channels
- The output power per channel
Guideline Télécom MSFB Technical Sheets ICOM IC-F30 LT 05/08/2002
10
Inhaltsverzeichnis
Andere Icom Transceiver Handbücher
Icom
Icom IC-F5330D Bedienungsanleitung
Icom
Icom IC-2GAT Bedienungsanleitung
Icom
Icom IC-V82 Bedienungsanleitung
Icom
Icom IC-706 Bedienungsanleitung
Icom
Icom IC-V21AT Bedienungsanleitung
Icom
Icom IC-756PROIII Bedienungsanleitung
Icom
Icom IC706MK2G Bedienungsanleitung
Icom
Icom IC-F4SR Bedienungsanleitung
Icom
Icom IC-4GAT Bedienungsanleitung
Icom
Icom IC-7800 Bedienungsanleitung
Icom
Icom IC-2720H Bedienungsanleitung
Icom
Icom IC-728 Bedienungsanleitung
Icom
Icom IC-F8100 Bedienungsanleitung
Icom
Icom IC-4SA Bedienungsanleitung
Icom
Icom IC-F521 Bedienungsanleitung
Icom
Icom IC-M500D Bedienungsanleitung
Icom
Icom IC-F30LT Bedienungsanleitung
Icom
Icom IC-F5061 Bedienungsanleitung
Icom
Icom IC-U101 Bedienungsanleitung
Icom
Icom IC-F21 Bedienungsanleitung
