ICP DAS USA I-7232D Einrichtungshandbuch

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----1

The I-7232D CANopen/Modbus Gateway

Quick Start User Guide

1. Introduction

This user guide describes how to implement the I-7232D module into

users’ applications in a quick and easy way. Therefore, it only provides the

basic instructions. If users want to know more detail information about the

I-7232D, please refer to the I-7232D user manual in the product CD or

download it from following web site:

http://www.icpdas.com/download/can/index.htm

The purpose of this manual is focused on helping users to quickly

familiarize themselves with the I-7232D module. Users can apply the I-

7232D module as follows.

CANopen

Device

PISO-CAN200/400

CPS_Modbus RTU

Gateway

CANopen

Salve

I-8421

PISO-CPM100

RS-485

Modbus RTU

(M-7000)

Modbus RTU

Master

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----2

2. Hardware structure

3. 7-segment LED

7-segment

LED Number

CAN Baud

rate

RS-485

Baud rate

0 10 K bps 1200 bps

1 20 K bps 2400 bps

2 50 K bps 4800 bps

3 125 K bps 9600 bps

4 250 K bps 19200 bps

5 500 K bps 38400 bps

6 800 K bps 57600 bps

7 1000 K bps 115200 bps

Bypass CAN

Bus Connector

7-segment

LED

RS-232 Port

(

connect to PC

)

Reserve for further use

RS-485 Baud rate:

Refer to the right

hand side table

CAN Baud rate:

Refer to the right

hand side table

Node ID:

0x00

(

)

~0x7F

(

127

)

n: Normal

Power Pin

RS-485 Port

(Connect to I/O modules)

Power LED

CAN Bus

Connector

CANopen

Status LED

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----3

4.How to Start

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----4

5.Configuration Installation

Step1: Install the CANopen/Modbus RTU Gateway Utility into your PC. Users can get

the setup file from the web site http://www.icpdas.com/download/can/index.htm or

the product CD in the path of “/Napdos/iCAN/CAN_Gateway/I-7232D”.

Step2: Before running the CANopen/Modbus RTU Gateway Utility, please connect the

COM1 of the I-7232D with the available COM port of your PC. Also, connect

the configured Modbus RTU modules with the COM2 of the I-7232D. The

architecture is displayed in the following figure.

(Note: We use the ICPDAS M-7000 series Modbus RTU modules for this demo, if users want to use any

other Modbus RTU device, please configure the communication parameters of this device firstly.)

Step 3: Turn off the I-7232D firstly. Connect the INIT* pin and the GND pin on the I-

7232D. Then, turn on the I-7232D.

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----5

Step 4: Run the CANopen/Modbus RTU Gateway Utility.

Step 5: Execute the CAN_MRU.exe file. The following figure will be displayed.

Then click the “connect” button.

(Note: When the CAN_MRU.exe can’t get the configuration information from the EEPROM, it may

response a Warning dialog as follows. This situation may be happen because the connection between

PC and I-7232D is broken during the CAN_MRU.exe is writing the data to the I-7232D EEPROM. Users

can repeat the steps from 2~5 to solve this problem)

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----6

Step 6: Click the “CAN Bus” button to configure the CAN communication parameters

for I-7232D.

Step 7: Click the “RS-485” button to configure the RS-485 parameters for the

CANopen/Modbus RTU gateway. These parameters need to match with the

communication parameters of Modbus RTU modules. Afterwards, click the

“Next” button to next step.

Step 8: You have to input the Modbus device NodeID, Relay Address, Register/Relay

Address and Data Length for one Modbus device connected with I-7232D.

These parameters are decided from this Modbus RTU device. Then click

“ADD” button to save the parameters settings. Repeat the action described

above if you have another Modbus device. When you finish these steps,

please click “Next” button to next step.

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----7

(Note: If you want to remove some device information, please select the instance number corresponding

to this device, and click the “Delete” button, the device information will be removed.)

Users can click on the “PDO Information” or “Modbus Information” button to view the PDO objects or

Modbus RTU devices configuration information. These information dialogs are shown below.

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----8

Step 9: If everything is ok, click the “Finish” button to create the EDS file and save the

related information into the EEPROM of the I-7232D.

Step 10: Turn off the I-7232D, and remove the wire between the Init* pin and GND pin

of the I-7232D, Then power on the I-7232D. When the I-7232D has finished

the initialization, the RUN LED on the I-7232D will be flashed about twice per

second, and the I-7232D is into the NMT pre-operational state. For more

information about the CANopen system and CANopen communication set,

please refer to the I-7232D user manual.

Inhaltsverzeichnis

Andere ICP DAS USA Tor Handbücher

ICP DAS USA

ICP DAS USA GW-7828 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tGW-735 1 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ICP CON GW-7557 Bedienungsanleitung

ICP DAS USA

ICP DAS USA GW-2139M Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7232D Bedienungsanleitung

ICP DAS USA

ICP DAS USA GW-7838-M Bedienungsanleitung

ICP DAS USA

ICP DAS USA DGW-521 Bedienungsanleitung

ICP DAS USA

ICP DAS USA GW-5492 Bedienungsanleitung

ICP DAS USA

ICP DAS USA GW-7663 Bedienungs- und Wartungsanleitung

ICP DAS USA

ICP DAS USA I-7540D Bedienungsanleitung

ICP DAS USA

ICP DAS USA ICP CON RMV-762D-MTCP Bedienungsanleitung

ICP DAS USA

ICP DAS USA iWSN-2200-E Bedienungsanleitung

ICP DAS USA

ICP DAS USA DNP-211 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PFN-2000 Series Gebrauchs- und Pflegehandbuch

ICP DAS USA

ICP DAS USA GW-2200 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA HRT-310 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ECAT-2610 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tGW-718 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ECAN-240-FD Bedienungsanleitung

ICP DAS USA

ICP DAS USA M2M-711D Installationsanleitung

ICP DAS USA

ICP DAS USA I-7231D Einrichtungshandbuch

ICP DAS USA

ICP DAS USA ICP CON RMV-762D-MTCP Bedienungsanleitung

ICP DAS USA

ICP DAS USA RMV-514 Bedienungsanleitung

ICP DAS USA

ICP DAS USA SMS-531 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung