ICP DAS USA PROFI-8455 Einrichtungshandbuch
Quick Start User Guide
Introduction
This user guide introduces the user how to implement the PROFI-8455
into their applications in a quick and easy way. Therefore, it only provides
the basic instructions. For more detail information about the PROFI-8455,
please refer to the PROFI-8455 user manual in the ICP DAS product CD or
download it from ICP DAS web site.
PROFI-8455 Hardware Structure
Status
Indicator
Address
PROFIBUS
(Data Comm.) I/O Expansion Slot
(Module Installation)
Console
(Prog. DL.)
Power Input
PROFI-8455 Connector and Pin Assignment
The PROFIBUS connector is a standard 9-pin D-Sub connector, there are
only 4 pins used in PROFI-8455. The pins VP and GND support the 5 volt
power to active terminal resistor, and the A-Line and B-Line is the data bus.
Pin No. Signal Meaning
3 B-Line Receive/Transmit data – plus
5 GND Power ground of active terminator
6 VP Power 5 volt of active terminator
8 A-Line Receive/Transmit data - minus
PROFI
-
8455
–
PROFIBUS
Remote I/O Unit
Status Indicator
PROFI-8455 provide three types of status indicators, they are PWR LED
(yellow), ERR LED (red) and RUN LED (green).
Status Indicator Meaning Recommend solution
ERR ON &
RUN OFF PROFI-8455 is offline
with no valid baud rate
(offline mode*)
Check the address setting of
PROFI-8455 and DP-master.
ERR Flash
(0.1 Sec) PROFI-8455 detects
baud rate, but is still
offline.(stop mode*)
Check the DP-Master is
ready to communicate with
PROFI-8455.
ERR Flash
(0.5Sec) PROFI-8455 Prm is
Fault.(Note 1) Check the setting of
PROFI-8455 in the master
interface and make sure of
the consistency.
ERR Flash
(1 Sec) PROFI-8455’s Cfg is
fault(Note 2) Same as above
ERR ON & RUN
ON PROFI-8455 is in clear
mode*. Sets the DP-Master from
clear mode to operation
mode
ERR OFF & RUN
ON PROFI-8455 is in
operation mode*.
PWR Flash
(1 Sec) PROFI-8455 detect
module(s) offline Find the reason of the fault of
corresponding module.
Terminating Resistors
In order to minimize the reflection effect of the signal transmission,
PROFIBUS device has to fit with an active terminal resistor at both first
node and last node. The connection of active terminating resistors is shown
in above circuit diagram. The PROFI-8455 doesn’t have any terminating
resistors inside. Therefore, users must add the terminator in external. In
general, PROFIBUS connector has terminating resistors inside, and there
is a switch to control the ON/OFF of the terminating resistors, as shown
below.
Terminator Switch
Terminator OFF
Terminator ON
PROFI-8455 – Setting and Module Installation
The following steps can help users to set and apply the PROFI-8455.
1. Load GSD file into the DP-Master Configuring software
DP-Master configuring software (Siemens Step7 or
ProfiCaptain etc...) loads IPDS0B0C.gsd file, and make sure of
the “PROFI-8455” label in “I/O” category. Finally, Loading
PROFI-8455 into PROFIBUS at the software and activate it.
2. Select I/O modules
Choose PROFI-8455 and add I/O module that you want to use.
Modify the system parameter “WD_On”, “Freeze/Sync Req.”,
“Lock/Unlock Req”, “Group-ID assignment”, etc… (modify by
user’s preference)
3. Set Parameter Data
Wait parameterization is an important step before data
exchange. In this stage, DP-Master provides the essential
parameter to PROFI-8455 include user parameters and module
parameters. Therefore, it must finish this setting before data
exchange.
1. User Parameter:
“User parameter”also called “system parameter”is the basic
parameters. The number of parameter is fixed regardless of the
number of modules. In PROFI-8455, there are two kinds of
parameter. They are Byte Order and Diagnosis Repot Period.
Byte-Order Parameter: If your system obeys the INTEL
data format, you should select Little-Endian mode; otherwise,
you should select Big-Endian mode.
Diagnosis Report Period Parameter: This parameter
dominates the time interval of each diagnostic message report.
The unit of this period is millisecond. The maximum time
interval is 65536 ms, the minimum is 0 ms.
2. Module Parameters:
The most of modules must be initialized before applying
them. Module parameters provide information about Operation
Code, Data Code or Enable Diagnosis, etc… Please refer to the
manual to know more information about these parameters.
4. Download Setting and Program into DP-Master
Users load the setting and program into DP-Master, and let it
go.
Users must finish these steps before starting to communicate with
PROFI-8455.
5. Module Installation:
In the expansion slots, users install the modules, and make
sure of correct installation. Notice that address mapping is order
by slot id of installed module (from left to right), and the
expansion slot that without module will be skipped.
6. Address Setting:
There are two hexadecimal rotary switches in PROFI-8455
panel. They dominate the address of PROFI-8455. The switch
labeled LSB is represented the low nibble of the address, and
the switch labeled MSB is represented the high nibble of the
address. For advance setting, please refer to PROFI-8455
User’s Manual.
After finishing the procedure, DP-Master will establish the connection
with PROFI-8455 and execute program automatically. RUN_LED indicates
the status of connection that you can observe.
PROFI-8455 – state flow chart
The state machine of PROFI-8455 is shown below. If your PROFI-8455
can’t establish connection with DP-Master, you can see Q/Ato solve it.
PROFI-8455 – Q&A
1. Q: How do I know the status of the PROFI-8455?
A: You can observe the RUN LED in PROFI-8455 panel. If RUN LED
is light, data is exchanging. Otherwise it must be error in the
previous state. You can see Q&A 3 to solve it.
2. Q: Have I must set the PROFI-8455’s address before power
applied?
A: You can change the address after power applied, but you should
let the PROFI-8455 offline at least 5 second. After 5 second offline,
PROFI-8455 will reset by itself, and then apply the new setting of the
rotary switches.
3. Q: If PROFI-8455 couldn’t establish communication with DP-Master,
what can I do?
A: In General, the PROFI-8455’s error is due to the following
reasons.
1. Parameter Fault- PROFI-8455’s ERR LED will have an interval of
0.5 second in each flash. It may reduce from “error module
selection”.
2, Configuration Fault-PROFI-8455’s ERR LED will have an interval
of 1 second in each flash. It may reduce from “error installation
order”.
3, DP-Master OFFLINE-PROFI-8455’s ERR LED will light until
establish data exchange connection. You should switch DP-Master
status from OFFLINE to OPERATE.
4, DP-Master STOP-PROFI-8455’s ERR LED will flash quickly
(time interval may less then 0.5 second). You should switch
DP-Master status from STOP to OPERATE.
4. Q: Which Modules is faster among the same Module Number
(I-87017 and I-8017H)?
A: I-8K series is faster than I-87K series. It is due to the
communication interface, I-8K use Parallel interface, and I-87K use
the serial communication.
5. Q: I feel that the reaction time of analog module in I-87K is slow. Why
does it?
A: It is due to low sampling rate. Beside the I-87017 series module,
the remainder analog input module has sampling rate with 10Hz
maximum. If you want to use the high sampling module, I-8017H and
I-87017 is the best choice.
6. Q: how can I use the additional function of I-87082?
A: Please refer to the “Byte Order and Data Address” chapter in
the PROFI-8455 user’s manual.
Inhaltsverzeichnis
Andere ICP DAS USA E/A-System Handbücher
ICP DAS USA
ICP DAS USA tM-P8 Bedienungsanleitung
ICP DAS USA
ICP DAS USA SG-3071-G Bedienungsanleitung
ICP DAS USA
ICP DAS USA WF-2000 Series Bedienungsanleitung
ICP DAS USA
ICP DAS USA ET-2242 Bedienungsanleitung
ICP DAS USA
ICP DAS USA I-3591 Bedienungsanleitung
ICP DAS USA
ICP DAS USA PISO-813 Bedienungsanleitung
ICP DAS USA
ICP DAS USA I-7088 Bedienungsanleitung
ICP DAS USA
ICP DAS USA PETL Series Bedienungsanleitung
ICP DAS USA
ICP DAS USA PCI-P16R16 Series Montageanleitung
ICP DAS USA
ICP DAS USA U-7500 Series Bedienungsanleitung
ICP DAS USA
ICP DAS USA I-7061D Bedienungsanleitung
ICP DAS USA
ICP DAS USA A-821PGH Series Bedienungsanleitung
ICP DAS USA
ICP DAS USA I-7053 FG Bedienungsanleitung
ICP DAS USA
ICP DAS USA P8R8-DIO Bedienungsanleitung
ICP DAS USA
ICP DAS USA PIO-D144 Series Bedienungsanleitung
ICP DAS USA
ICP DAS USA CAN-2018C Bedienungsanleitung
ICP DAS USA
ICP DAS USA I-9018W Bedienungsanleitung
ICP DAS USA
ICP DAS USA PCI-P8R8 Bedienungsanleitung
ICP DAS USA
ICP DAS USA PIO-D144U Bedienungsanleitung
ICP DAS USA
ICP DAS USA I-7061 Bedienungsanleitung
Beliebte E/A-System Handbücher anderer Marken
WAGO
WAGO 750-344 Bedienungsanleitung
Teknim
Teknim TWM-1887 Bedienungsanleitung
Intelligent Appliance
Intelligent Appliance IA-2662-E Bedienungsanleitung
BERGHOF
BERGHOF ECC DIO 16/16 Bedienungsanleitung
Advantech
Advantech PCM-27J3AU Installations- und Betriebshandbuch
Festo
Festo CP-E08-M12-CL Bedienungsanleitung
