ICPDAS I-2533 Bedienungsanleitung

I-2533 CAN to Fiber Multi-Mode Bridge - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

I-2533

CAN to Fiber Multi-Mode Bridge

Quick Start Guide

1. Introduction

This quick start helps users to apply the I-2533 in users’ applications

quickly. If users need the details of I-2533, please refer to the I-2533 user

manual. Users can free download it from the web site as follows or get it

from product CD (path: CAN/Converter/I-2533).

I-2533 Website

http://www.icpdas-usa.com/i_2533.html

I-2533 CAN to Fiber Multi-Mode Bridge - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

2. Hardware Installation

Before using I-2533, some things must be done.

1. Prepare one pair of I-2533.

2. Set the CAN baud rate of each I-2533 by using rotary switch. You

can refer to the following table for details. (If you set the rotary

switch to “A”, please use utility tool to do the configuration before.)

I-2533 CAN to Fiber Multi-Mode Bridge - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Check the application structure, and determine if the terminator resistor is

needed or not. You can find it at the position as follows.

I-2533 CAN to Fiber Multi-Mode Bridge - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Connect the fiber port of these I-2533, CAN port, power line and frame

ground. The pin assignment and wire connection are as follows. When

finished, run your application with the I-2533.

I-2533 CAN to Fiber Multi-Mode Bridge - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Utility Tool

When users want to use user-defined baud rate or set the message filter, I-2533 utility

tool may be needed. It can be free downloaded from the following web site or get it in

the product CD (path: CAN/Converter/I-2533 /Software):

http://www.icpdas-usa.com/i_2533.html

After getting the utility tool, please follow the following steps to set the baud rate and

message filter.

Step0: Power off the I-2533. Set the rotary switch to “F”, and connect the PC available

COM port with the COM port of the I-2533. Users can find the communication cable in

the product box. When connecting to the COM port of I-2533, the TxD pin of the cable

is connected to the TXD pin of the COM port, RXD pin of the cable is connected to the

RXD pin of the COM port, and GND pin of the cable is connected to the GND pin of

the COM port. Then, power on the I-2533.

Step1: Execute the I2533_Utility.exe, the dialog of the I-2533 Utility will be poped up.

Select the PC COM port which is connected with the COM port of the I-2533. Then,

click “Connect” button.

I-2533 CAN to Fiber Multi-Mode Bridge - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

Step2: Users can set the baud rate on the “User-defined Baud Rate” field. Here, fill

“250000” for 250 kbps. Then, set the filter by using the “from” field, “to” field, and “Add”

button. For example, If users want to pass the CAN message with ID 0x4 and 0x5 in the

CAN 2.0A specification. Fill the value “4” in the “from” field of CAN 2.0A, and the value

“5” in the “to” field of CAN 2.0A.

Step3: Click “Add” button to add this configuration. The configuration is shown on the

“Pass List” field. If the “Pass List” is not empty, only the messages matched with the

“Pass List” will be passed. If the “Pass List” filed is empty, it means all-pass. If users

want to pass the message with ID 0x0 in the CAN 2.0A specification, fill the value “0” in

both of “from” and “to” field and click “Add” button.

I-2533 CAN to Fiber Multi-Mode Bridge - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

Step4:.The method of configuring the message filter of the CAN 2.0B messages is

similar with the configuration steps of the message filter of the CAN 2.0A messages.

After finishing all of the configurations, click “Save all configuration” to store the

configuration in the I-2533.

Step5: When the procedure is successful, the following message will be shown.

Step6. After finishing the configuration, set the rotary switch value to “0” ~ “A” and

reboot the I-2533. The CAN message filter will be applied automatically in the value “0”

~ “A” of the rotary switch. The CAN baud rate set by utility is only appled when the

rotary switch is set to “A”.

I-2533 CAN to Fiber Multi-Mode Bridge - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Dimension

Inhaltsverzeichnis

Andere ICPDAS Netzwerk-Router Handbücher

ICPDAS

ICPDAS MSM-6226G Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise