IDEAL EVOMAX 2 Series Bedienungsanleitung
When replacing any part on this appliance, use only spare parts that you can be assured conform to
the safety and performance specification that we require. Do not use reconditioned or copy parts that
have not been clearly authorised by Ideal.
For the very latest copy of literature for specification and maintenance practices visit our website
www.idealcommercialboilers.com where you can download the relevant information in PDF format.
USER GUIDE
EVOMAX 2
30 40 60 80 100 120 150
30P 40P 60P 80P 100P 120P
August 2019
UIN 219417 A02
2
CONTENTS
1. Introduction ................................................... 3
Safety .............................................................. 3
Electricity Supply ............................................. 3
Important Notes............................................... 4
Minimum Clearances....................................... 4
2. Boiler Operation ............................................ 5
Controls Diagram............................................. 5
To light the boiler ............................................. 6
Operating Status.............................................. 7
Settings............................................................ 8
3. Installer Connections.................................. 20
4. Faults............................................................ 21
Faults - Hardware (Thermistors, Actuators)... 22
Faults - Temperature Supervisions................ 23
Faults -
System (Flame, Fan, Hydraulic, etc.)
. 24
Faults - Internal System................................. 25
5. General Information .................................... 26
To shut down the boiler.................................. 26
To relight the boiler ........................................ 26
Frost Protection ............................................. 26
Boiler Overheat Thermostat .......................... 29
Condensate Drain.......................................... 26
Escape of Gas............................................... 27
Cleaning ........................................................ 27
6. System Set up information......................... 28
3
EVOMAX 2
30, 40, 60, 80, 100, 120, & 150
30P, 40P, 60P, 80P, 100P & 120P
Natural Gas & Propane
Destination Countries: GB, IE
1. INTRODUCTION
The EVOMAX 2 is a wall mounted, room
sealed, super efcient condensing boiler
featuring full sequence automatic spark
ignition and fan assisted combustion.
Due to the very high efciency, condensate
is produced from the ue gases and this
is drained to a suitable disposal point
through the plastic waste pipe at the
bottom of the boiler. A condensate
‘plume’ will also often be visible at the
ue terminal.
SAFETY
Current Gas Safety (Installation & Use)
Regulations or rules in force.
In your own interest, and that of safety, it
is the law that this boiler must be installed
and maintained by a suitably qualied
Gas Safe registered engineer or in IE a
competent person, in accordance with the
above regulations.
The appliance should be serviced at
least once a year by a suitably qualied
Gas Safe registered engineer or in IE a
competent person.
It is essential that the instructions in this
booklet are strictly followed, for safe and
economical operation of the boiler.
ELECTRICITY SUPPLY
The appliance must be earthed.
Supply 230 V - 50 Hz, 4 Amp fuse.
This appliance is intended to be
connected to the supply via a double-pole
switch, having a 3mm contact separation
in both poles, serving only the boiler and
system controls. Alternatively, a 3-pin
UNSWITCHED socket may be used.
4
IMPORTANT NOTES
• This appliance must not be operated
without
the casing correctly tted and forming
an adequate seal.
• If the boiler is installed in a
compartment then the compartment
MUST NOT be used for storage
purposes.
• Do not store objects around or on the
boiler, and keep access clear at all
times.
• Do not obstruct ventilation ducts,
condensate pipework, grilles or
openings in the boiler room, room
space or compartment that the
appliance is installed in, or the
passage of combustion and ventilation
to the boiler.
• Do not turn off the boiler if it is to be
left unattended in frosty weather.
• If it is known or suspected that a fault
exists on the boiler then it MUST NOT
BE USED until the fault has been
corrected by a suitably qualied Gas
Safe registered engineer or in IE a
competent person.
• Flammable materials must not
be placed in close proximity to
the appliance. Materials giving off
ammable vapours must not be stored
in the same room as the appliance.
• This appliance can
be used by children 8
years and above. Also
persons with reduced
physical, sensory or
mental capabilities, or
lack of experience and
knowledge, provided
they have been given
supervision or instruction
concerning use of the
appliance in a safe
way and understand
the hazards involved.
Children shall not play
with the appliance.
Cleaning and user
maintenance shall not be
made by children without
supervision.
• Children should be supervised to
ensure that they do not play with the
appliance.
In cases of repeated or continuous shutdown
a suitably qualified Gas Safe registered
engineer or in IE a competent person
should be called to investigate and rectify
the condition causing this and carry out an
operational test after each intervention on the
device. Only the manufacturers original parts
should be used for replacement.
MINIMUM CLEARANCES
Clearances of 300mm (12”) below, 25mm
(1”) at the sides and 450mm (17 3/4”) at the
front of the boiler casing must be allowed
for servicing.
5
BACK
OK
A B C D E F
A. ROTARY KNOB
• Enter a menu, if in the normal
operation screen, and highlight the
rst menu item.
•
Scroll up (anti-clockwise) or down
(clockwise) in a menu
• Change the value in parameter
setting.
• If an error is showing in the title
bar, scroll to the associated error
screen(s), and return.
B. LCD DISPLAY SCREEN
• Menu and status display.
C. BURNER LED
• Will be on if the burner is lit.
D. SELECT BUTTON
• Enter a menu, if in the normal
operation screen, and highlight the
rst menu item.
• Enter the highlighted menu (sub
menu or parameter), if in a menu or
sub menu.
• If in a parameter setting, select a
parameter which will then ash for
adjustment, once adjusted using the
rotary knob press again to store and
move on.
E. BACK BUTTON
• In a menu, return to the previous
menu layer.
• In parameter setting, exit the
parameter without storing the value.
• In a guided assistant, go back to the
previous screen.
F. RESET BUTTON
• Reset the associated boiler module
error, if a resettable (lockout) error is
active.
• Return to the normal operation
screen.
2. BOILER OPERATION
CONTROL DIAGRAM
6
TO LIGHT THE BOILER
A. Stand alone boiler, or a master
boiler in a cascade, or a master
boiler with an extension module:
Set the operating mode in the plant
menu operating mode to: Automatic
Ensure that there is a demand
present on the boiler from the
external controls, depending upon the
conguration.
If there are no local heating or DHW
circuits, set the plant / operating mode
to: Day
If there are local heating circuits,
set one of them - heating circuits /
HC1 Boiler 1.1 or HC2 Boiler 1.2 /
Operating mode to: Day
If there is a local DHW circuit set the
DHW / Operating mode / DHW1 Boiler
1 to: Day
If there is an extension module
congured with Heating circuits or
DHW circuits set the Operating mode
to: Day
e.g. Heating circuits / Operating mode
/ HCx EMy.z
DHW / Operating mode / DHWx
EMy.z
Key: x is the Heating or DHW circuit
number, y is the Extension Module
designation and z its local Heating or
DHW circuit designation.
B. Slave Boiler in a Cascade:
Refer to the Installation manual.
The boiler will commence the ignition sequence, supplying heat to the system. Ensure that
the controls are then set to the operating mode required.
Note. Not all menus and options will be available depending upon the access level selected.
7
OPERATING STATUS
The status screens are dependent upon the boiler conguration, they are shown below:
IDEAL Evomax 2 150kW
Operation: Htg. with capacity
Capacity Set point: 40%
Capacity: 0%
Flow temp: 40.2ºC
IDEAL Evomax 2
Operation: Htg. with temp.
Voltage: 5.6V
Flow Set point: 40.2ºC
Flow temp: 40.2ºC
IDEAL Evomax 2 150kW
Operation: Htg. with capacity
Voltage: 5.6V
Capacity Set point: 40%
Capacity: 0%
IDEAL Evomax 2 150kW
Status: OpenTherm
Operation: Day
Room set point: 20.0ºC
Flow set point: 60.0ºC
IDEAL Evomax 2 150kW
Status:
Operation: Night
Tank temperature: 45.0ºC
Flow set point: 30.0ºC
IDEAL Evomax 2 150kW
Operation: Htg. with temp.
Flow Set point: 40.2ºC
Flow temp: 40.2ºC
Master non cascade
Master / Non-cascade Slave
Menu item: Heating circuit / Status / Summary /
HC1 Boiler 1.1
Menu item: DHW / Status / Summary / HC1
Boiler 1.1
Master non cascade,
0-10V control
The heating circuits and DHW circuits also have status screens associated with them. e.g.
8
Menu
Plant
Heating circuits
DHW
Heating circuits
Operating mode
Room temperature
Flow temperature
Heating circuits
Status
Operating mode
Room temperature
Flow temperature
Heating circuits
HC1 Boiler 1.1
HC2 Boiler 1.2 HC1 Boiler 1.1
Room temperature. day
Room temperature. night
Room temperature. holiday
HC1 Boiler 1.1
Operating mode
Standby
Room temperature
HC1 Boiler 1.1
HC2 Boiler 1.2
1. Heating Circuits
a. Operating mode selection:
Every heating circuit can be
individually set to one of the
following modes;
Standby / Time clock single day
/ Time clock multiple day / Day /
Night.....e.g.:
SETTINGS
b. Room temperature
A temperature can be set for each
heating circuit for the following periods:
Day / Night / Holiday.....e.g.:
Each heating circuit that is congured has the following settings:
Room temperature, day
20.0
9
Heating circuits
Room temperature
Flow temperature
Settings
Time clock
Heating circuits
Flow temperature
Settings
Time clock
Holiday program
Flow temperature
HC1 Boiler 1.1
HC2 Boiler 1.2
Settings
HC1 Boiler 1.1
HC1 Boiler 1.1
Flow temperature. day
Flow temperature. night
Flow temperature. holiday
c. Flow temperature
A maximum ow temperature can
be set for each heating circuit for
the following periods
Day / Night / Holiday.....e.g.:
d. Settings
Each heating circuit has a number
of settings that can be congured.
Most settings are only accessible
at Installer access levels.
Day / Night / Holiday.....e.g.:
Flow temperature, day
70.0
HC1 Boiler 1.1
Preheat
Heating limit
Room temp. switch diff.
Preheat
Preheat switch
Maximum preheat time
i. Preheat - Preheat can be enabled
for a heating circuit and a
maximum time can be set.
CONTINUED OVERLEAF
10
Preheat switch
On/Off
Preheat switch
On/Off
Preheat
Preheat switch
Maximum preheat time
Maximum preheat time
120 minutes
HC1 Boiler 1.1
Preheat
Heating limit
Room temp. switch diff.
Pump
Heating limit switch
On/Off
Heating limit
Heating limit switch
Heating limit temperature
Heating limit
Heating limit switch
Heating limit temperature
Heating limit switch
On/Off
ii. Heating Limit- Heating limit can be
enabled for a heating circuit with a
limit temperature set.
HC1 Boiler 1.1
Preheat
Heating limit
Room temp. switch diff.
Preheat
Preheat switch
Maximum preheat time
i. Preheat - Preheat can be enabled
for a heating circuit and a
maximum time can be set.
Dieses Handbuch passt für folgende Modelle
13
Inhaltsverzeichnis
Andere IDEAL Kessel Handbücher
IDEAL
IDEAL LOGIC+ Combi 30 Bedienungsanleitung
IDEAL
IDEAL i 24 Bedienungsanleitung
IDEAL
IDEAL Vogue S15 Bedienungsanleitung
IDEAL
IDEAL Imax Plus II F90 Benutzerhandbuch
IDEAL
IDEAL he15 Bedienungsanleitung
IDEAL
IDEAL Mexico RS 3/100 Datenblatt
IDEAL
IDEAL he24 Bedienungsanleitung
IDEAL
IDEAL Exalt FSB 110 Benutzerhandbuch
IDEAL
IDEAL RS 50 Montageanleitung
IDEAL
IDEAL Optia FF 30 Versionshinweis
IDEAL
IDEAL IMAX XTRA E80 Bedienungsanleitung
IDEAL
IDEAL Harrier GTS 5 Bedienungsanleitung
IDEAL
IDEAL INSTINCT 40 Bedienungsanleitung
IDEAL
IDEAL he15 Bedienungsanleitung
IDEAL
IDEAL Independent C24 Bedienungsanleitung
IDEAL
IDEAL Project Heat 15 Bedienungsanleitung
IDEAL
IDEAL Logic HEAT 12 Bedienungsanleitung
IDEAL
IDEAL IDEAL SPRINT RS 75 Bedienungsanleitung
IDEAL
IDEAL MINI C24 Bedienungsanleitung
IDEAL
IDEAL Vogue S15 Bedienungsanleitung
Beliebte Kessel Handbücher anderer Marken
Vaillant
Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung
Radijator
Radijator BIO max 23.1 Bedienungsanleitung
Brunner
Brunner BSV 20 Bedienungsanleitung
Buderus
Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung
Potterton
Potterton 50e Datenblatt
UTICA BOILERS
UTICA BOILERS TriFire Bedienungsanleitung
