IDEAL ND 3405-1 Bedienungsanleitung

#61-322

#61-324

320 Series Contractor

Grade Multimeter

WARNING!

1. DO NOT UNDER ANY CIRCUMSTANCES EXCEED THESE

RATINGS:

• Voltage is not to exceed 1000 Volts.

• Resistance, Capacitance, Logic and Continuity functions

are not to be performed on circuits capable of delivering

greater than 600 Volts.

• Current measurements are not to be performed on

circuits capable of delivering greater than 500 Volts

2. To avoid electrical shock hazards and/or damage to the meter:

• Do not exceed the voltage ratings for the meter. Use

caution when measuring voltage.

• Do not use during electrical storms. AC power sources

with inductive loads or electrical storms may result in

high voltage. High energy transients can damage meter

and present a dangerous shock hazard.

• Turn off power to the circuit or device being measured

before taking resistance and capacitance measurements.

Fully discharge all capacitors before measuring.

3. Ensure meter is in proper working order before using.

Visually inspect meter for damage. Performing a continuity

check can verify proper operation. If the meter reading goes

from overload to zero, this typically means the meter is in

proper working order.

4. Visually inspect leads for damage before using. Replace if

insulation is damaged or leads appear suspect.

5. Never ground yourself when taking electrical measurements.

Do not touch exposed metal pipes, outlets, fixtures etc.

Keep your body isolated from ground by using dry clothing,

rubber shoes, mats, or any other approved insulating

material. Keep your fingers behind the finger guards on the

probes. Work with others.

6. Before beginning all unknown measurements, set meter to

highest possible range.

7. Before breaking a circuit for testing, turn off the power to the

circuit. When disconnecting from a circuit, disconnect the

hot lead first, then the common lead.

8. Disconnect the meter from the circuit before turning off any

indicator, including motors, transformers, and solenoids.

1. MIN/MAX Switch

• Pressing this button once results in the displayed maxi-

mum value of the current reading.

• Pressing the min/max button once more results in the

displayed minimum value of the current reating.

• If pressed a third time “Max Min” will flash on the LCD

indicating that the minimum and maximum value are

being recorded while the current reading is displayed.

• Pressing the min/max button for >2 seconds exits the

Min/Max mode.

2 3

2. RS-232 Button (61-324 only)

• Pressing the RS-232 button activates data acquisition

• When the RS-232 button is pressed RS232 will appear

in the upper middle of the LCD display

• Data will be sent to the computer through the optical

RS-232 connection.

• Press the RS-232 button again to stop data acquisition

3. Range Button

• Pressing the range button selects the manual ranging

mode.

• When the range button is pressed RANGE will appear

in the upper left of the LCD display.

• When in the manual range mode, pressing the range

button changes the meaurement range.

• To return to auto ranging, hold the range button for >2

seconds.

4. Hold Switch

• The hold button is used to hold the mesured value for all

functions.

• The value is displayed along with the annunciator.

•This function can be used in the min/max or peak

min/max mode.

5. Backlight Buttong (61-324 only)

• Pressing the backlight button enables a light source

allowing the end-user to view the LCD in dark areas.

Auto Power Off (APO)

If the meter idles for more than 10 minutes, the meter automati-

cally turns the power off. When this happens, the state (non-

logic measurement) of the meter is saved, the meter can be

turned back on by pushing any key switch or changing the

rotary switch. The meter will give an alarm in 15 seconds

before the meter automatically turns the power off. To disable

the auto power off function, power up the meter while pressing

either the range, RS-232 or min/max. button.

Overload Protection

Function Overload Protection

VAC & VDC 1000V

AAC & ADC A input: 1A(600V) fast blow fuse

µA input: 600V RMS

Ohms (Ω) 600VAC/600VDC

Diode 600VAC/600VDC

Continuity 600VAC/600VDC

Unit of Measure Multipliers

For your reference, the following symbols are often used to

make measurement easier:

Symbol Verbal Multiplier

M mega x 1,000,000

k kilo x 1,000

m milli ÷ 1,000

µ micro ÷ 1,000,000

True RMS AC Volt

Range Resolution Accuracy Max. Display

600mV 100µV 600.0

6V 1mV ±(0.9% reading 6.000

60V 10mV + 5 digits) 60.00

600V 100mV 600.0

1000V 1V 1000

AC Conversion Type: AC conversions are AC-coupled, true

RMS responding, calibrated to the RMS value sine wave input.

Input and Impedance: 10MΩless than 100 pF.

Crest Factor: +1.5% additional error for C.F. from 1.4 to 3

+3.0% additional error for C.F. from 3 to 4

To Measure True RMS AC Voltage:

1. Plug the black test lead into the COM port and the red test

lead into the Hz V ΩµA port.

2. Set the rotary switch to the Vposition.

3. Connect the meter in parallel with the load or circuit.

4. Measure AC Voltage.

Circuit Connection:

DC Volts

Range Resolution Accuracy Max. Display

600mV 100µV 600.0

6V 1mV ±(0.5% reading 6.000

60V 10mV + 2 digits) 60.00

600V 100mV 600.0

1000V 1V 1000

Input Impedance: 10MΩ(over 1000MΩin 600mV range)

To Measure DC Voltage:

1. Plug the black test lead into the COM port and the red test

lead into the Hz V ΩµA port.

2. Set the rotary switch to the v position.

3. Connect the meter in parallel with the load or circuit.

4. Measure DC Voltage

Circuit Connection:

True RMS AC Current

Range Resolution Accuracy Voltage Max

Burden

60mA 10µA +(1.5% 2V max 60.00

600mA 100µA reading +5 600.0

AC Conversion Type: AC conversions are AC-coupled, true

RMS responding, calibrated to the RMS value sine wave input.

Overload Protection: A input: 1A (600V) fast blow fuse

Crest Factor: +1.5% additional error for C.F. from 1.4 to 3

+3.0% additional error for C.F. from 3 to 4

Frequency Response: 40 Hz ~ 500Hz

To Measure True RMS AC Current:

1. Plug the black test lead into the COM port and the red test

lead into the mA.

2. Set the rotary switch to the mA.

3. Connect the meter in series with the load or circuit.

4. Measure AC Current.

Circuit Connection:

DC Current

Range Resolution Accuracy Voltage Max

Burden

600µA 0.1µA < 4mV / µA 600.0

6000µA 1µA ±(1.0% reading 6.000

60mA 10µA + 2 digits) 2V max 60.00

600mA 100µA 600.0

Overload Protection: A Input: (600V) fast blow fuse

µA Input: 600V RMS

To Measure DC Current:

1. Plug the black test lead into the COM port and the red test

lead into the mA or Hz V ΩµA port.

2. Set the rotary switch to the mA or µA position.

3. Connect the meter in series with the load or circuit.

4. Measure DC Current.

Circuit Connection:

Frequency/RPM

Range Resolution Sensitivity Accuracy

6000Hz 1Hz

60KHz 10Hz 100mV RMS Frequency:

600KHz 100Hz 0.01% ±1 digit

6MHz 1KHz 250mV RMS

60MHz 10KHz 1V RMS

Overload Protection: 600V rms

*Less than 20Hz the sensitivity is 1.5V

To Measure Frequency:

1. Plug the black test lead into the COM port and the red test

lead into the Hz V ΩµA port.

2. Set the rotary switch to the HZ RPM position.

3. Connect the meter in parallel with the load or circuit.

4. Measure Frequency or RPM.

Circuit Connection:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IDEAL Multimeter Handbücher

IDEAL

IDEAL 61-340 Bedienungsanleitung

IDEAL

IDEAL 602 Bedienungsanleitung

IDEAL

IDEAL 61-340 Bedienungsanleitung

IDEAL

IDEAL 61-764 Bedienungsanleitung

IDEAL

IDEAL SecuriTEST Bedienungsanleitung

IDEAL

IDEAL 61-704 Bedienungsanleitung

IDEAL

IDEAL 61-340 Bedienungsanleitung

IDEAL

IDEAL 61-614 Bedienungsanleitung

IDEAL

IDEAL 61-312 Bedienungsanleitung

IDEAL

IDEAL ND 2350-1 Bedienungsanleitung

IDEAL

IDEAL 61-603 Bedienungsanleitung

IDEAL

IDEAL ND 3511-1 Bedienungsanleitung

IDEAL

IDEAL 61-340 Bedienungsanleitung

IDEAL

IDEAL ND 2365-1 Bedienungsanleitung

IDEAL

IDEAL ND 1075-2 Bedienungsanleitung

IDEAL

IDEAL 61-797 Bedienungsanleitung

IDEAL

IDEAL ND 4950-3 Bedienungsanleitung

IDEAL

IDEAL 61-497 Bedienungsanleitung

IDEAL

IDEAL 61-310 Bedienungsanleitung

IDEAL

IDEAL 61-497 Bedienungsanleitung

IDEAL

IDEAL 480 Series Bedienungsanleitung

IDEAL

IDEAL ND 2351-1 Bedienungsanleitung

IDEAL

IDEAL 61-327 Gebrauchs- und Pflegehandbuch

IDEAL

IDEAL ND 2352-1 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung