Identiv Freedom 50-40-1 Bedienungsanleitung
identiv.com •sales@identiv.com •+1 888-809-8880
Single Port (FB1) Freedom Bridge™
Installation Guide
PART NUMBERS 50-40-1, 50-40-1L 50-24-1
PHYSICAL SPECIFICATIONS
Length 76 mm (3.00 in.)
Width 47 mm (1.85 in.)
Height 17 mm (0.67 in.)
Weight 26 g (1.20 oz.)
Max Readers 1
Max Input 2
Max Output 1
Certications
Electrical: UL294 and UL294B
Power over ethernet: IEEE 802af
EMI Radiation: FCC Part 15 Class B
SUMMARIZED LEVELS OF
ACCESS CONTROL COMPONENTS
Destructive Attack Level I
Line Security Level I
Endurance Level I
Standby Power Level I
Single Point Locking Level I
BASE PLATE MOUNTING
Dimension Millimeters Inches
A116.07 4.57
B78.74 3.10
C15.24 0.60
D85.59 3.37
E10.16 0.40
F58.42 2.30
E
D
A
C
BF
Freedom Bridges should only be installed in dry, non-condensing
environments. The ambient temperature of the environment should
range between -40°C and 50°C.
Freedom Encryption Bridges should only be mounted to non-conductive
surfaces. Incorrect mounting may short-circuit the electronics, which will
cause it to malfunction.
DC power, reader, input contact, and output device wires should
be between 16-28 AWG. They should also be stripped 5.5mm to
sufciently t the terminal blocks and ensure that they do not come in
contact with each other.
INSTALLATION REQUIREMENTS
For each of the following steps, be sure to reference the wiring
diagram on page 2 for additional details:
1. Connect a Wiegand Reader to the Wiegand Reader Input on the
Freedom Bridge.
A. If the reader has a shield wire, connect the shield wire
to the 0v terminal on the Wiegand Reader Input. If an
extension cable is used between the reader and the
Freedom Bridge, connect the reader’s shield wire to the
cable’s shield, then connect the cable’s shield to the 0v
terminal on the Wiegand Reader Input.
B. Any unused wires on the reader must be evenly snipped
and have their tips insulated using electrical tape or
equivalent. The shield wire on the reader must also be
completely insulated.
2. If you have any supervised input contacts, wire them to the Digital
Contact Inputs using Method 1 or Method 2.
3. If you have any non-supervised input contacts, wire them to the
Digital Contact Inputs.
4. If you have a relay output contact, wire it to the Relay Output.
5. Supply power to the Freedom Bridge using either or both of the
following methods:
A. A 2.25 – 5.25 W Power over Ethernet (PoE) port on an
Ethernet switch connected to the Freedom Bridge using a
Cat5e or Cat6 cable.
B. 12 – 16 Vdc & 350 mA (300 mA external & 50 mA
internal) DC power connected directly to the TB1 terminal
on the Freedom Bridge.
6. If you are not using PoE to power your Freedom Bridge, connect
a Cat5e or Cat6 cable from any port on an Ethernet switch to the
RJ- 45 connector on the Freedom Bridge. Note: Ethernet only
supports a maximum cable length of 100 m.
7. To congure and add the Freedom Bridge to a MESH/Freedom
Server, refer to the MESH/Freedom Solution Guide manual.
INSTALLATION PROCEDURE
INSTALLATION GUIDE
TECHNICAL DATA IS SUBJECT TO CHANGE WITHOUT NOTICE.
REVISION DATE: 2020-06-02
Identiv (NASDAQ: INVE) is a global provider of physical security and secure identication. Identiv’s products, software, systems, and
services address the markets for physical and logical access control, video analytics and a wide range of RFID-enabled applications.
For more information, visit identiv.com or email sales@identiv.com.
© Identiv, Inc. | All rights reserved. This document is Identiv public information.
Wiring Reference
OPTIONAL DC POWER IN
0v DC Power Ground
+12 DC Power Input
TB1
Requirements
• 12 – 16 Vdc
• 350 mA
(300 mA external & 50 mA internal)
1
DIGITAL CONTACT INPUTS
R1 - R2 Ground
In1 - In2 Non-supervised or supervised
inputs 1 - 2
4
RELAY OUTPUT
Nc Normally closed
CCommon
No Normally open
Relay Contact DC: 30 Vdc @ 1 Adc
AC: 60 Vac @ 0.5 Aac
5
3
Press and hold this button for 10 seconds to
reset the conguration back to default.
RESET BUTTON
This product is sensitive to Electrostatic Discharges (ESD).
Take precautions while handling the product by using proper grounding straps at all times.
CAUTION
NOTE
As long as the total current of the reader plus a door strike DOES NOT EXCEED 300mA,
you may power the door strike using the power out and ground from the reader Input terminal block.
A ashing green “Ready” LED light on
the Freedom Bridge circuit board indicates
that the bridge is powered but not
connected to a server.
A solid green “Ready” LED light indicates
that the Freedom Bridge has established a
connection to the server and is ready to use.
2
WIEGAND READER INPUT
+12 Power Output
0v Ground
D1 Data 1 Input
D0 Data 0 Input
Ld LED Output
Bz Buzzer Output
Power Output
Using PoE
• 12.0 - 16.5 Vdc
• 300 mA max current
Power Output
Using DC
• 8.5 - 16.0 Vdc
• 300 mA max current
Dieses Handbuch passt für folgende Modelle
2
Andere Identiv Netzwerk-Hardware Handbücher
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
