IEI Technology WAFER-4823 Bedienungsanleitung

November 27, 2003

WAFER-4823

DX4-100 MHz with LCD/CRT

& Ethernet SBC

User Manual

Version 2.1

The information in this document is subject to change

without prior notice in order to improve reliability, design

and function and does not represent a commitment on

the part of the manufacturer.

In no event will the manufacturer be liable for direct,

indirect, special, incidental, or consequential damages

arising out of the use or inability to use the product or

documentation, even if advised of the possibility of such

damages.

This document contains proprietary information protected

by copyright. All rights are reserved. No part of this

manual may be reproduced by any mechanical, electronic,

or other means in any form without prior written

permission of the manufacturer.

Trademarks

WAFER-4823 is a registered trademark of ICP Electronics

Inc. IBM PC is a registered trademark of International

Business Machines Corporation. Intel is a registered

trademark of Intel Corporation. AMI is a registered

trademark of American Megatrends, Inc. Other product

names mentioned herein are used for identification

purposes only and may be trademarks and/or registered

trademarks of their respective companies.

Table of Contents

CHAPTER 1 INTRODUCTION.............................................................3

1.1 SPECIFICATIONS ....................................................................................4

1.2 PACKAGE OF CONTENTS........................................................................7

CHAPTER 2 INSTALLATION...............................................................8

2.1 LAYOUT ...................................................................................................8

2.2 UNPACKING PRECAUTIONS..................................................................10

2.3 CPU SETTINGS ....................................................................................10

2.4 WATCHDOG TIMER...............................................................................11

2.5 DISK-ON-CHIP™FLASH DISK ..........................................................12

2.6 RI PIN SETTINGS FOR SERIAL PORT2................................................12

2.7 THE SETTINGS OF SERIAL PORT2............................................................13

2.8 FREE IRQ3 AND IRQ4 SETTINGS .....................................................13

2.9 CLEAR CMOS SETUP ..........................................................................14

2.10 REALTEK8019AS SETTING ............................................................14

CHAPTER 3 CONNECTION ................................................................15

3.1 FLOPPY DISK DRIVE CONNECTOR ......................................................15

3.2 IDE DISK DRIVE CONNECTOR ...........................................................16

3.3 PARALLEL PORT....................................................................................17

3.4 SERIAL PORTS......................................................................................18

3.5 KEYBOARD/MOUSE CONNECTOR........................................................19

3.6 EXTERNAL SWITCHES AND INDICATORS............................................20

3.7 EXTERNAL POWER CONNECTOR..........................................................20

3.8 EXTERNAL SPEAKER.............................................................................21

3.9 PC/104 CONNECTION BUS................................................................22

3.10 VGA/LCD INTERFACE CONNECTOR...............................................24

3.11 LAN RJ45 CONNECTOR..................................................................25

3.12 DIGITAL I/O.....................................................................................25

CHAPTER 4 AMI BIOS SETUP.........................................................27

4.1 GETTING START...................................................................................27

4.2 STANDARD CMOS SETUP...................................................................29

4.3 ADVANCED CMOS SETUP...................................................................30

4.4 ADVANCED CHIPSET SETUP ................................................................33

4.5 PERIPHERAL SETUP..............................................................................34

4.6 AUTO-DETECT HARD DISK.................................................................35

4.7 CHANGE SUPERVISOR PASSWORD .....................................................36

4.8 AUTO CONFIGURATION WITH OPTIMAL SETTINGS............................37

4.9 AUTO CONFIGURATION WITH FAIL SAFE SETTINGS .........................38

4.10 SAVE SETTINGS AND EXIT..............................................................39

4.11 EXIT WITHOUT SAVING...................................................................40

APPENDIX A A.WATCH-DOG TIMER.............................................41

APPENDIX B I/O INFORMATION...................................................43

APPENDIX C DIMENSION...................................................................45

APPENDIX D APPENDIX D. DIGITAL INPUT AND OUTPUT

……………………………………………………………..46

Chapter 1 Introduction

Thank you for choosing WAFER-4823 DX4-100 with LCD/CRT &

Ethernet Single Board Computer. WAFER-4823 is a stand alone

board with PC/104 connector, which comes equipped with ACC

Maple Chipset (includes DX4-100 CPU) and advanced high-

performance multi-mode I/O,LCD Controller and Ethernet

function, designed for the system manufacturers, integrators, or

VARs to provide all the performance, reliability, and quality at a

reasonable price.

An advanced high performance super I/O function is supported

by the Maple chipset. The on-chip UARTs are compatible with the

NS16C550. The parallel port and IDE interface are compatible

with IBM PC/AT and XT architecture's, as well as EPP and ECP.

The LCD/CRT controller TOPRO TP6508 can provide the LCD and

CRT display at the same time. The LCD interface connector is a

44-pin 2.0mm pitch type.

The most outstanding feature in the WAFER-4823 is the built-in

PC/104 expansion bus. Based on the PC/104 bus, you can easily

install over thousands of PC/104 modules from hundreds

vendors in the world. The WAFER-4823 has external power

connector that can let it connects to power supply directly. It is

very suitable for your standalone applications.

1.1 Specifications

The WAFER-4823 DX4-100 with LCD/CRT & Ethernet

Single Board Computer provides the following

specification:

zSystem

CPU ACC Maple, includes DX4-100 CPU

DMA channels 7

Interrupt levels 15

Real-time

clock/calendar STM48T86 or equivalent chip and quartz

oscillator, powered by lithium battery for

over 10 years of data retention.

zMemory

DRAM

memory 1 piece of 72-pin SIMM up to

32MB

zLCD/CRT Interface

Chipset TP6508

Resolution 1MB EDO RAM on board support 800 x 600

resolution for STN and TFT LCD Flat Panel.

Simultaneous LCD and CRT display.

Display

Memory 1MB EDO RAM on board.

zEthernet Interface

Chipset Realtek RTL-8019AS chipset (on board).

Type 16-bit Ethernet, Novell NE2000 compatible,

10Base-T 10 MBps.

Connectio

n on-board RJ-45 connector.

zIntegrated Multi I/O

IDE hard disk drive

interface Supports up to two IDE hard disk

drives. Can be disabled by BIOS

Setup.

Floppy disk drive

interface Supports two 2.88 MB, 1.44MB,

1.2MB, 720KB, or 360KB floppy disk

drives. Can be disabled by BIOS

Setup.

Two high speed

Serial ports One ports RS232 port, and one RS232

port or RS422/485 port.

PS/2

Mouse/Keyboard

Connector

6-pin Mini DIN Keyboard Connector.

zDigital I/O

4 inputs and 4 outputs

zIndustrial features

Watch-dog

timer can be set for 1,2,10,20,110,or 220 seconds period.

Reset or NMI is generated when CPU does not

periodically trigger the timer. Your program uses hex

043 and 443 to control the watch-dog and generate a

system reset.

PC/104

expansion

bus

can be set for 1,2,10,20,110,or 220 seconds period.

Reset or NMI is generated when CPU does not

periodically trigger the timer. Your program uses hex

043 and 443 to control the watch-dog and generate a

system reset.

External

power

connector

5-pin male connector (model: 2571-08TS

Keyboard

connector 6-pin mini-DIN keyboard connector.

zGeneral

Power Consumption +5V @ 1.92A ( DX4-100MHz, 32MB RAM)

Operating Temperature 0°~ 60°C

Humidity 5% ~ 95%, non-condensed

Dimension 102.01mm(W) x 146.48mm(L)

1.2 Package of Contents

WAFER-4823 package includes the following items:

zOne WAFER-4823 DX4-100 with LCD/CRT &

Ethernet single board computer

zOne printer cable

zOne FDD/HDD cable

zOne 6-pin mini-din keyboard/mouse adapter

cable

zOne power cord

zOne RS-232/422/485 cable

zOne user manual

Chapter 2 Installation

This chapter describes how to install the WAFER-4823.

The layout of WAFER-4823 is shown on the next page

and the Unpacking Precautions that you should be

careful with is described on the following page. Also

included is the jumpers and switches setting for this

board’s configuration, such as: CPU type selection,

system clock setting and Watchdog timer.

2.1 Layout

< Please, refer to next page >

Inhaltsverzeichnis

Andere IEI Technology Hauptplatine Handbücher

IEI Technology

IEI Technology NANO-ULT5 Bedienungsanleitung

IEI Technology

IEI Technology KINO-DH810 Bedienungsanleitung

IEI Technology

IEI Technology IOWA-8522 Bedienungsanleitung

IEI Technology

IEI Technology KINO-QM670 Bedienungsanleitung

IEI Technology

IEI Technology HYPER-BT Bedienungsanleitung

IEI Technology

IEI Technology IMBA-X9654 Bedienungsanleitung

IEI Technology

IEI Technology NANO-BT Series Bedienungsanleitung

IEI Technology

IEI Technology IEM-945GSE Bedienungsanleitung

IEI Technology

IEI Technology KINO-HM551 Bedienungsanleitung

IEI Technology

IEI Technology ICPMB-7880 Bedienungsanleitung

IEI Technology

IEI Technology IMBA-C2260-i2 Bedienungsanleitung

IEI Technology

IEI Technology IMBA-C2260-i2 Bedienungsanleitung

IEI Technology

IEI Technology KINO-DCM236 Bedienungsanleitung

IEI Technology

IEI Technology NANO-GM45A Bedienungsanleitung

IEI Technology

IEI Technology IMBA-8650 Bedienungsanleitung

IEI Technology

IEI Technology IMBA-Q870-i2 Bedienungsanleitung

IEI Technology

IEI Technology IMBA-H310 Bedienungsanleitung

IEI Technology

IEI Technology eNOVA-945GSE Bedienungsanleitung

IEI Technology

IEI Technology IMB-H110 Bedienungsanleitung

IEI Technology

IEI Technology PM-US15W Bedienungsanleitung

IEI Technology

IEI Technology POS-478 Bedienungsanleitung

IEI Technology

IEI Technology PCIE-9450 Bedienungsanleitung

IEI Technology

IEI Technology JUKI-C400 Series Bedienungsanleitung

IEI Technology

IEI Technology KINO-CV-KINO-CV-N26001 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung