Ikelite 69121 Bedienungsanleitung
200DLM/A Underwater Housing for Sony ZV-E1
Mirrorless Cameras
Product # 69121
2
Introduction
Thank you for your purchase of Ikelite products.
Our primary focus is to provide quality, professional grade products
for use in and under water. Our products are designed, manufactured,
and distributed from our sole facility in Indianapolis, USA where we
started in 1962.
We are available if you have any questions or want photo advice.
reply within 1 business day.
An electronic version of this instruction manual is available for
download via the product page on our website:
https://www.ikelite.com
In the Box
• Housing
• Rear o-ring # 0110 (installed)
• Front o-ring # 0132.36 (installed)
• Camera mount # 95434 (installed)
• .050” hex key # 0945.11
• Silicone lubricant 1cc tube
3
Important Notices
»This housing requires a compatible DLM lens port for
waterproof operation. The housing is not waterproof without a
DLM lens port attached.
»Do not pull the shutter trigger without a camera installed. You
may accidentally detach or damage the control spring.
»Never leave a housing in a rinse tank, even if it is the only
system in the tank. Accidental damage may occur when the
user walks away from a housing while it is in the rinse tank.
»Do not use alcohol, cleaning agents, spray lubricants, Rain-X,
or other solvents on the housing or lens port. Use of an
incompatible chemical compound can damage the plastic and
o-rings, and may result in leaking.
»If you will be using the system in strong surf it is
recommended to draw a vacuum on the housing using the
optional vacuum kit (sold separately).
4
Contents
Product Registration 1
Introduction 2
In the Box 2
Important Notices 3
Getting to Know Your Housing 6
Tray Mounts 9
Accessory Ports 9
Setting Up Your Camera 9
Pre-Installation Checklist 9
Camera Settings 10
Exposure Settings 10
Power Save 10
Back Button Focus 10
Setting Up Your Housing 11
Opening the Housing 11
Installing the Camera 11
Closing the Housing 12
Turning the Camera On/Off 13
Attaching a Lens Port 14
Installing the Lens and Port 14
Setting Up An External Strobe 17
About Fiber Optic Cords 17
Attaching a Fiber Optic Cord 18
Getting in the Water 18
Final Check 18
Entering the Water 19
Shooting Underwater 19
Learning about Underwater Photography 20
Maintaining Your Housing 20
5
Post-Dive 20
Lens Port 21
Storage 21
Servicing Recommendations 22
Lubricating Controls 22
Lubricating Push Buttons 23
Lubricating Control Shafts 24
Troubleshooting 25
Spare Parts 27
Limited Warranty 28
Service and Repairs 28
Contact Us 29
6
Getting to Know Your Housing
Shutter
Lid snap
Tray mounts
Lens
release
Port mount
Accessory
port
7
SONY ZV-E1 / 200 FT
69121 MADE IN USA
Fn
Fn
MENU
MENU
Rear o-ring
SONY ZV-E1 / 200 FT
69121 MADE IN USA
Fn
Fn
MENU
MENU
Left
Fn (function)
Playback
Lid
snap
hook
Up
Delete
Right
Center
Control dial
Control wheel
Down
C2 (Custom button 2)
Menu
8
Thumbscrew
groove On/off (power)
MOVIE
Front o-ring
C1 (Custom
button 1)
Accessory
port
Still/Movie/S&Q Switch
9
Tray Mounts
This housing features two 1/4-20 threaded tray mounts on the bottom
of the housing. The spacing between the tray mounts is 3” (76.2 mm).
Optional tray with handles and mounting hardware are sold separately.
It is recommended to detach and thoroughly rinse the tray mounts,
tray, and mounting hardware, with fresh water routinely during
continuous use and prior to storage.
Accessory Ports
This housing features two spare accessory ports which may be used
for the attachment of optional accessories. These ports accept ttings
designed for a 1/2” through or 1/2-20 threaded hole.
The optional B1A Bulkhead may be installed in place of the top
accessory port for the use of an optional DL2 DS Link Sony TTL
Converter.
The optional Vacuum Kit # 47012 may be installed in place of the side
accessory port. A hand pump with gauge allows you to draw a vacuum
on the house to simulate water pressure and check for leaks prior to
entering the water.
Visit ikelite.com for an updated list of compatible products.
»Do not remove or loosen the accessory port plug unless you
are installing a compatible accessory.
Setting Up Your Camera
Pre-Installation Checklist
1. Insert a fully charged camera battery.
2. Insert a properly formatted memory card.
3. Remove any attached lanyard or neck strap.
10
Camera Settings
• Set REC w/ Shutter to ‘On’ to use the shutter lever on the side of
the housing to start or stop recording movies when the shooting
mode is set to [Movie] or [S&Q motion].
• Set Red Eye Reduction to “Off” when using an external strobe.
Exposure Settings
Refer to the Cheat Sheets in the Photo School section of our website
for recommendations on exposure settings for a wide variety of
shooting situations:
https://www.ikelite.com/blogs/cheat-sheets
Power Save
It is recommended to set the Power Save Start Time to the shortest
interval that makes sense for your shooting.
Instead of turning the camera off and on to conserve battery, the
camera will automatically sleep after the pre-set interval. To wake the
camera, simply perform an operation such as pressing the shutter
button halfway down.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Ikelite Kamerazubehör Handbücher
Ikelite
Ikelite 6973.03 Bedienungsanleitung
Ikelite
Ikelite 47140 Bedienungsanleitung
Ikelite
Ikelite 6146.16 Bedienungsanleitung
Ikelite
Ikelite 6870.80 Bedienungsanleitung
Ikelite
Ikelite 6843.72 Bedienungsanleitung
Ikelite
Ikelite 9306.35 Bedienungsanleitung
Ikelite
Ikelite 6950.52 Bedienungsanleitung
Ikelite
Ikelite DSC-V3 Bedienungsanleitung
Ikelite
Ikelite 69621 Bedienungsanleitung
Ikelite
Ikelite SLR-DC Housing Bedienungsanleitung
Ikelite
Ikelite 6860.03 Bedienungsanleitung
Ikelite
Ikelite WD-3 Bedienungsanleitung
Ikelite
Ikelite 6243.35 Betriebsanleitung
Ikelite
Ikelite 6241.13 Betriebsanleitung
Ikelite
Ikelite 6210.61 Betriebsanleitung
Ikelite
Ikelite 4077.67 Technisches Datenblatt
Ikelite
Ikelite Olympus Mju760 Bedienungsanleitung
Ikelite
Ikelite 6014.10 Betriebsanleitung
Ikelite
Ikelite F60fd Betriebsanleitung
Ikelite
Ikelite 6251.03 Verdrahtungsschema
