IKUSI STC 100 Bedienungsanleitung

User Manual

STC

100

REF. 4465

4 General safety instructions

4 Types of notices

5 Basic safety instructions

6 Introduction

6 General description

7 General use of the headend

8 Basic installation and conﬁguration

8 Assembly, connection of signals and power supply

9 Description of the user interface

10 IKUNET bus conﬁguration

14 Conﬁguration of general parameters

15 Module conﬁguration

20 Service Management

23 Advanced functions

23 Save/Restore Function

23 Internet Access

24 Network functions

25 Advanced global transport processing

26 Reports

30 CE Certiﬁcate

30 STC-201

Contents

General safety instructions

JRead all of this user manual carefully before plugging in the unit.

JAlways have these instructions to hand during installation.

JFollow all of the instructions and safety notices regarding unit handling.

Types of notices

The meaning of the safety notices used in this manual are described below.

DANGER OF DEATH OR INJURY

This safety notice indicates a possible danger for the life and health of people.

Not following these instructions may lead to serious consequences to health and

may even cause fatal injuries.

RISK OF DAMAGE TO THE UNIT

This safety notice indicates a possible dangerous situation. Not following these

instructions may lead to the unit being damaged.

NOTE

This type of notice is a note containing applicable advice and useful information

for optimum use of the unit.

HANDLING THE INSIDE OF THE UNIT IS FORBIDDEN

This notice forbids any work that may affect the working order of the unit or its

warranty.

DO NOT DISPOSE OF AS URBAN WASTE

This type of notice indicates that the unit must not be disposed of as unselected

urban waste.

DANGER

ATTENTION

General safety instructions/Basic safety instructions

Basic safety instructions

DANGER OF DEATH OR INJURY

JDo not install the unit during an electrical storm. This could lead to electro-

static discharge from lightning.

JDo not open the unit. There is a risk of electrostatic discharge.

RISK OF DAMAGE TO THE UNIT

JThe unit must be appropriately ventilated. Install the unit in a dust-free

location. Do not place the unit in a location where the ventilation slots are

covered or blocked. Install the unit in a location with at least 20 cm around it

free of other objects.

JDo not expose the unit to rain or moisture. Install the equipment in a dry lo-

cation with no inltration or condensation of water. Should a liquid enter the

unit, disconnect it immediately from the mains.

JKeep the unit away from ammable objects, candles and anything that may

cause a re.

JConnect the unit to an easily accessible power socket. In the event of an

emergency, it will then be possible to quickly unplug the unit.

JDo not expose the unit to sources of heat (sun, heating, etc.).

DANGER

ATTENTION

Introduction/General description

Introduction

JTo ensure the correct use and installation of the headend, it is necessary to read the

user and troubleshooting procedure manuals corresponding to the complete solution

and to each of the individual modules.

JIKUSI reserves the right to modify the contents of this manual without prior warning.

General description

The headend described in this manual is made up of the following modules:

JSTC-100 (Ref. 4465): DVB-S/S2 to DVB-T transmodulator (QPSK/8PSK to COFDM).

JCFP-507 (Ref. 4439): power supply +12 V/+24 V.

STC-100

KEY

A STC-100 module

B CFP-700 module

C CFP-507 module

1 Input 1 DVB-S/S2 channel

2 Loop output

3 LNB remote power supply

4 Slot for CAM

5 DB-9 port

6 DC power supply

7 RJ-45 ports for IKUNET bus

8 Coupling loop DVB-T output

9 Output +12 V (5 A)

10 Output +24 V (60 mA)

11 Output +18 V/22 kHz (300mA)

12 Output +13 V/22 kHz (300mA)

13 Output +18 V/0 kHz (300mA)

14 Output +13 V/0 kHz (300mA)

15 Output +12 V (7 A)

16 Output +24 V (60 mA)

Introduction/General use of the headend

JCFP-700 (Ref. 4401): power supply +12 V/+24 V for selection of polarisation.

JBAS-900 (Ref. 4411): base-support with capacity for 9 modules (dimensions:

563x257x24 mm).

JMS-0504 (Ref. 1023): stand-alone multiswitch (4 SAT inputs and 4 outputs).

NOTE

Please read the detailed information in the manuals for the modules included in

their respective packaging.

General use of the headend

This headend is designed for the emission of DVB-T (COFDM) signals from the input of free

or encrypted DVB-S/S2 signals (QPSK/8PSK to COFDM).

NOTE

The DVB-T (COFDM) output signal requires a trunk amplier for the correct distri-

bution in installations for a large number of sockets.

ENEN

Basic installation and conﬁguration/Assembly, connection of signals and power supply

Basic installation and conﬁguration

NOTE

A PC with an Ethernet network card and a CAT-5E Ethernet crossover cable are

required for communication with the headend.

NOTE

To display the graphics provided in the headend conguration program correctly,

we recommend installing the Mozilla Firefox web browser (www.mozilla.com) in

the control PC.

Assembly, connection of signals and power supply

1) Attach the modules to the base one by one following the instructions given in the

manuals for each module.

NOTE

IKUSI recommends the modules are assembled in the order shown in the above

gure:

JRight: CFP-700/CFP-507 power supplies.

JLeft: STC-100 transmodulators

654

KEY

1 DVB-S/S2 signal input

2 DVB-T signal output

3 Bridging line in loop mode

4 Power supply bridges

5 IKUNET

6 CAM + SmartCard + protection with safety

screws

Basic installation and conﬁguration/Description of the user interface

JLast STC-100 on the right: Master STC-100 with the DVB-T output signal.

2) Connect the input and output signal connections in accordance with the instructions

for the module manuals and the diagram shown in the previous gure.

3) Distribute the headend power supply as symmetrically as possible (see example in

above gure).

Description of the user interface

The interface permits the user to communicate easily and comfortably with the headend.

The layout of the menus and submenus of the interface is shown in the following diagram:

The upper part of the interface displays messages about the communication status with the

headend. Each message is colour-coded:

FGreen: noties that the instruction has been carried out.

FRed: indicates that the instruction could not be performed and gives the reason.

KEY

1 Exit button

2 Information button

3 Print button

4 Main menu

5 Submenus

6 Tabs

7 Status message

8 Work area

Basic installation and conﬁguration/IKUNET bus conﬁguration

IKUNET bus conﬁguration

The IKUNET bus is an Ethernet communication bus between the headend modules. The

IKUNET bus is installed using Ethernet pigtails supplied with the modules. If n is the

number of station modules, n-1 Ethernet pigtails are required.

Deﬁnition of the master module

NOTE

JRemember the PC conguration prior to the connection with the IKUNET

bus.

JThe denition of the master module must be made with an STC-100 module.

NOTE

In mixed STC and MTC congurations, an STC module may never be an MTC

module master. In these cases, the master module must be an MTC module and

the STC modules are reserved for conguration as slave modules.

1) Start the conguration of the IKUNET bus for

the headend with the modules disconnected

from each other.

2) Connect the selected module ( A ) to the PC ( B

) via its Ethernet connection and using an RJ-45

cable ( C ).

3) In the PC (Windows XP) go to 







.

4) Select the 

 checkbox. Enter the following IP con-

guration parameters:

F: 10.254.254.2

F: 255.255.255.0

F: 10.254.254.1

5) Click on the  button.

6) Enter the IP address http://10.254.254.254 in the web browser. This takes you to the

home page of the connected module.

STC-100 STC-100

Inhaltsverzeichnis

Andere IKUSI Industrieelektrik Handbücher

IKUSI

IKUSI STC 200 Bedienungsanleitung

Beliebte Industrieelektrik Handbücher anderer Marken

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Technisches Handbuch

Abtech

Abtech HVJB Series Leitfaden

Murata

Murata GRM0335C1H8R1DA01 Series Bedienungsanleitung

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Bedienungsanleitung

Eaton

Eaton Ulusoy HMH24-04 Bedienungsanleitung

Murata

Murata GJM0335C1E4R4BB01 Series Bedienungsanleitung

Newlong

Newlong NP-7H Bedienungsanleitung

Stahl

Stahl 8575/12 Bedienungsanleitung

SI Pegasus Bedienungsanleitung

Murata

Murata GRM1555C1H2R7CA01 Seies Bedienungsanleitung

Murata

Murata GRM0225C1E6R4BA03 Series Bedienungsanleitung

Cooper Power Systems

Cooper Power Systems VXE15 Bedienungsanleitung

S&C

S&C Vista SD Bedienungsanleitung

Murata

Murata GRM0335C2A7R3CA01 Series Bedienungsanleitung

Siemens

Siemens 3VA9988-0BM10 Bedienungsanleitung

Siemens

Siemens SITRANS LVS100 Bedienungsanleitung

Murata

Murata GRM32ER60G227ME05 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MP-Series Bedienungsanleitung