Iluminar ILi3 Bedienungsanleitung

USER

MANUAL

iLi3 MODEL 240W

1-877-540-5588

iluminarlighting.com

[email protected]

IL-i326FSG-120

CONTENTS

• Observe all safety precautions (see page 8), seek the services of a

qualified electrician, installation professional, or call ILUMINAR Lighting

technicians for assistance.

• DO NOT handle or touch the fixture while in use.

• Connect the fixture only to the power sources of the appropriate voltage

using the correct AC plug type. Protect power cables from being pinched,

walked on, or otherwise damaged. Be especially careful where the power

cable enters the power outlet to the unit. Only connect the fixture to an

electrical outlet or extension cord of comparable standard and level

rating. Connect the fixture ONLY to the power sources of the correct

voltage using the plug received.

• The fixture should only be cleaned as directed. Always seek service for

your system by qualified service personnel if any of the following occur:

1. The fixture shows a noticeable change in performance.

2. The power-supply cord or plug is damaged.

3. The fixture has been dropped, or the exterior is damaged.

Please read this manual thoroughly prior to

installing or operating the ILUMINAR iLi3.

Pre-Install Information ........................................

Technical & Physical Specications......................

Hardware & Accessories ....................................

Hanging Instructions ...........................................

Daisy Chain Instructions .....................................

Important Cautions & Warranty ...........................

5-6

1-877-540-5588

iluminarlighting.com

[email protected]

Subject to change without notice.

ILI3 240W LED SPECTRUM

VELENGTH NM

MOUNTING & COVERAGE

1m / 3'

1.2m / 4'

15-30cm / 6-12”

1193mm / 46.97"

458mm / 18.04"

50mm / 1.97"

PPF

Efficacy

Input Current

Input Power

Output Power

Output Voltage

Min Power Factor

THD

Crest Factor

BTU

Rated Mains Voltage

Voltage Range (+/-10%)

Mains Frequency

Dimmable

Ambient Temperature

Max. Temperature

Relative Humidity

Plug Type

Color Temperature

Color Rendering Index

Finishing Mounting Height

Emitter Cooling

Light Distribution +/- 5%

Waterproof Rating

LED Lifespan (90% of Life)

624 µmol/s

2.6 µmol/j

6.70A

240 W

221.1

33V

0.9

15%

0.99

816

120-277V AC

100-277V

50 / 60Hz

1-10V Controllable

-20..+45°C

75°C/167°F

98%

Power Cord Sold Seperately

4000k

6”-12” to top of Canopy

Passive / Extruded Case

125º

IP65 for Damp/Wet Conditions

55,000+ hours

TECHNICAL SPECIFICATIONS

LED Lighting Solution

MODEL:

VOLTAGE:

WATTS: 240W2.6

100-277V

SKU: IL-i326FSG-120

PHYSICAL SPECIFICATIONS

Length

Width

Height

Weight

1193mm

458mm

50mm

7kg

46.97"

18.04"

1.97"

15.4lb

120V

208V

240V

277V

347V

480V

0.71A

0.51A

2.11A

1.2A

1.09A

0.9A

245W

239W

251W

2.44W

241W

240W

VOLTAGE AND AMPERAGE DRAW

HARDWARE AND ACCESSORIES

The iLi3 can be hung from

steel cables or can be

mounted to a rack.

Before you begin installation,

check that you have all the

necessary parts to begin.

1 iLi3 Fixture

1 Power Cable

4 Steel Hanging Cables with attached

cylindrical locks for hanging

IN THE BOX

1-877-540-5588

iluminarlighting.com

[email protected]

Lay the central mast on a at table top or surface with the attachment

brackets facing UP. Attach each LED Bar by aligning the plastic clips

and carefully sliding them into place until you hear a soft click.

CONNECTION INSTRUCTIONS

Once the plastic clips are all snapped in place, attach the A/C cables

coming from the mast to each LED bar by aligning the connector pins and

pressing the ends together. Lock by twisting in opposite directions.

Once all the LED bars are fastened into place and A/C cables are attached

to the mast, turn the xture over (this may require more than one person).

Ensure the at surface is clear of anything that could damage the delicate

diodes.

SLIDE

! CAUTION when handling your ILUMINAR iL Fixture.

The LED array should NOT come in contact with sharp

objects.DONOTtouchdiodesorapplydirectforcetothe

diodes as this can/will cause permanent damage.

Subject to change without notice.

61-877-540-5588

iluminarlighting.com

[email protected]

HANGING INSTALLATION DAISY CHAIN CONNECTIONS

If you plan to utilize several LEDs in your room or facility, one of the many

benets of the ILUMINAR LED is that you can “daisy chain” one xture to

another to save space and use only one outlet to run several lamps, thus

minimizing the amount of cords used in your space.

If you plan to utilize the TOUCH Controller or ILUMINAR HASH

Controller,youcanconnecttheyellowconnectionsfromthecontroller

to the xture and then connect the Daisy Chain Controller Cable from

xture to xture. Please consult with our lighting layout designers to

ensure proper spacing of outlets for your unique setup.

A/C 100-277V

50/60 Hz INPUT

(to power outlet)

Yellow Tip

Controller Cable

(to Controller)

Controller Cable

Daisy Chain

(yellow)

A/C Daisy

Chain Cable

(blue)

Controller Cable

Daisy Chain

(yellow)

! NEVERattachtwoACinputplugs.Safely

install only one AC Power Cable.

Attached the secure hooks to the xture.

Loop the hanging wire as shown around the support beam (as shown

in Figure A). Press down at base of hook to slide to adjust the mounting

height of the xture (Figure B).

! NEVERattachtwoACinputplugs.Safely

install only one AC Power Cable.

Onesideonlyused

to Daisy Chain

power to xture 2.

Once xture is hanging with all LED bars installed, connect the power

cable (blue tip) from the outlet to one side of the xture. DO NOT EVER

connect two power cables from the wall to the xture.

AC 100-277V

50/60 Hz INPUT

FIGURE A

FIGURE B

Subject to change without notice.

CAUTION

1. Leave at least one inch of space between the xture and the mounting

area for maximum performance and lifespan.

2. ALWAYS wear protective eye wear when looking directly at the diodes to

prevent eye damage.

3. Only handle, clean or move xture when it’s unplugged and completely

cool.

4. Keep the xture free of dust, debris, deposits to ensure the maximum

potential of the xture.

5. NEVERuseclothtocleanthediodes.Thiswillscratchthediodesandcould

potentially break or dislodge them.

6. DO NOT use chemicals to clean the xture. Use ONLY low pressure air or

low pressure water to remove dust and debris.

At ILUMINAR, we stand behind our products and our

technology as well as our customers. All ILUMINAR xtures

are backed by our 5-Year Guarantee. Please visit our

website iluminarlighting.com/warranty for more information.

1-877-540-5588

iluminarlighting.com

[email protected]

GUARANTEE

Please read the following list carefully prior to beginning installation.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Iluminar Leuchte Handbücher

Iluminar

Iluminar iL1c Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung

Iluminar iLi3 Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken