IMG STAGE LINE PARC-150ZOOM Bedienungsanleitung

ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS

COB LED Spotlight

PARC-150ZOOM

Order No. 38.8110

INSTRUCTION MANUAL

Table of contents

INTRODUCTION ……………………………………………….…………………………..2

SAFETY INSTRUCTIONS…………………………………………………………………2

OPERATING DETERMINATIONS…………………………………………….…………..3

DESCRIPTION OF THE DEVICE…………………………………………………………4

INSTALLATION………………………………………………………………….…………..4

OPERATION……………………………………………………………………….………...5

Stand alone operation…………………………………………………………….…………5

Master slave operation…………………………………………………………….……..…5

DMX controlled operation………………………………………………………….…….…5

Addressing…………………………………………………………………………….…..…5

Control board………………………………………………………………………….…..…5

DMX protocol………………………………………………………………………….…..…7

TECHNICAL SPECIFICATIONS……………………………………………………..……8

Every person involved with installation. operation and maintenance of this fixture has to

-be qualified

-follow the instruction of this manual

-consider this manual to be part of the total product

-Keep this manual for the entire service life of the product

-pass this manual to every future owner or use of the product

CAUTION!

Keep this device away from rain and moisture

Unplug mains lead before opening the housing

For your own safety, please read this user manual carefully before you initially start-up

INTRODUCTION

Thank you for choosing our fixture, if you follow up the instruction given in this manual we be sure

that you will enjoy this product for a long period of time.

SAFETY INSTRUCTIONS

CAUTION!

Be careful with your operations.

With a dangerous voltage you can suffer a dangerous electric shock when touching the wires.

This device has left our premises in absolutely perfect condition. In order to maintain this condition and

to ensure a safe operation, it is absolutely necessary for the user to follow the safety instruction and

warning notes written in this user manual.

Never let the power-cord come into contact with other cables! Handle the power-cord and all

connections with the mains with particular caution! Never touch them with wet hands as this could lead

to mortal electrical shock. Never modify, bend, strain mechanically, put pressure on, pull or heat up the

power cord. Never operate next to sources of heat or cold. Disregard can lead to power cord damages,

fire or mortal electrical shock. The cable insert or the female part in the device must never be strained.

There must always be sufficient cable to the device. Otherwise, the cable may be damaged which may

lead to mortal electrical shock. Make sure that the power-cord is never crimped or damaged by sharp

edges. Check the device and the power-cord from time to time. If extension cords are used, make sure

that the core diameter is sufficient for the required power consumption of the device. All warnings

concerning the power cords are also valid for possible extension cords.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the

power-cord by the plug. Never pull out the plug by tugging the power-cord. Otherwise, the cable or plug

can be damaged leading to mortal electrical shock. If the power plug or the power switch is not

accessible, the device must be the disconnected via the mains. If the power plug or the device is dusty,

the device must be take out of operation, disconnected and then be cleaned with a dry cloth. Dust can

reduce the insulation which may lead to mortal electrical shock. More severe dirt in and at the device

should only be removed by a specialist.

There must never enter any liquid into power outlets, extension cords or any holes in the housing of the

device. If you suppose that also a minimal amount of liquid may have exerted the device it must

immediately be disconnected. This is also valid, if the device was exposed to high humidity. Also if the

device is still running, the device must be checking by a specialist if the liquid has reduced any

insulation. Reduced insulation can cause mortal electrical shock. There must never be any objects

entering into the device. This is especially valid for metal parts. If any metal parts like staples or coarse

metal chips enter into the device, the device must be taken out of operation and disconnected

immediately. Malfunction or short-circuits caused by metal parts may cause mortal injuries. Never look

directly into the light source, as sensitive persons may suffer an epileptic shock (especially meant for

epileptics). Keep away children and amateurs. Never leave this device running unattended.

OPERATING DETERMINATIONS

This device is designed for permanent operation. Consistent operation breaks will ensure that the

device will serve you for a long time without defects. Do not shake the device. Avoid brute force when

installing or operation the device. Never lift the fixture by holding it at the projector-head. As the

mechanics may be damaged. When choosing the installation-spot, please make sure that the device is

not exposed to extreme heat, moisture or dust. There should not be any cable lying around. Please

make sure that the fixture can not be touched or bumped. Your endanger your own and the safety of

others.

This device must never be operated or stockpiled in surroundings’ where splash water, rain, moisture

or fog may harm the device. Moisture or very high humidity can reduce the insulation and lead to mortal

electrical shocks. When using smoking machines, make sure that the device is never exposed to the

direct smoke jet and is installed in a distance of 0.5 meters between smoke machine and device. The

room must only be saturated with an amount of smoke that the visibility will always be more then 10

meters.

The housing must never touch surrounding surfaces or objects. Make sure that the area below the

installation place is blocked when rigging, dragging or servicing the fixture. For overhead use

(mounting height >100cm), always fix the fixture with an appropriate safety-rope. Fix the safety-rope at

the correct fixation points only. The safety-rope must never be fixed at the transport handles. Only

operate the fixture after having check that the housing is firmly closed and all screws are tightly fastened.

The maximum ambient temperature Ta = 40°C must never be exceeded. Operate the device only after

having become familiarized with its functions. Do not permit operation by persons not qualified for

operating the device. Most damages are the result of unprofessional operation. Please use the original

packaging if the device is to be transported. Please consider that unauthorized modifications on the

device are forbidden due to safety reasons! Never remove the serial barcode from the device as this

would make the guarantee void. If this device will be operated in any way different to the one described

in this manual, the product may suffer damages and the guarantee becomes void. Furthermore, any

other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.

DESCRIPTION OFTHE DEVICE

Features

>150W RGB COB LED

>12/5/4/3 channelsin option

>Variable electronic dimmer (0-100%) and electronic strobe

>LED operation menu with function buttons

>Electronic zoom

>Build-in program with speed adjustment

>16 bitdimmer effect and White balance

>Temperature sensor via software to control fans speed against overheat

>5 different DMX channel modes.Including STAG,ARC, AR1D, AR1S and HSV

INSTALLATION

Rigging

The installation of the projector has to be built and constructed in a way that it can hold 10 times

the weight for 1 hour without any harming deformation.

IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including

calculating working load limits, installation material being used, and periodic safety inspection of

all installation material and the projector. If you lack these qualifications, do not attempt the

installation yourself, but instead use a professional structural rigger. Improper installation can

result in bodily injury and or damage to property.The projector had to be installed out of the reach

of people.

DANGER OF FIRE! When installing the device, make sure there is no highly-inflammable

material (decoration articles, etc.) within a distance of min. 0.5m.

DMX 512 connection/ connection between fixture

The wires must not come into contact with each other, otherwise the fixture will not work at all or

properly. Please note the starting address depends upon which controller is being used. Only use a

DMX cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or

one fixture to another.

Connection with the mains

The earth has to be connected. The device must onlybe connected with an electric installation

carried out in compliance with IEC standards.

OPERATION

After you connected the effect to the mains, the fixture starts running

Stand Alone operation

In the stand alone mode, the fixture can be usedwithout controller

Master/slave-operation

The master/slave-operation enables that several devices can be synchronized and controlled by

one master-device

DMX controlled operation

You can control the projectors individually via your DMX-controller

Addressing

The control board allows you to assign the DMX starting address,

Note: it’s necessary to insert the XLR termination plug (with 120 ohm) in the last device in the

link in order to ensure proper transmission on the DMX data link.

Control board

The control board offer several features. You can simple set the starting address, run

the pre-programmed program or make a reset.

The main menu is accessed by pressing the Mode/Esc-button, Browse through the submenu by

pressing Up or Down .Press the Enter-button in order to select the desired menu. You can change the

selection by pressing Up or Down, Confirm every selection by pressing the Enter-button. You can leave

every mode by pressing the Mode/Esc-button .The functions provided are described in the following

setting.

MENU MAP

The device has two operation modes. It can be operated in Stand Alone or in DMX controlled

When in Master/Slave Synchronization Mode, only one in a series chain can be set as the master.

The main menu is accessed by pressing the Mode/Esc-button.Browse through the submenu

by pressing Up or Down. Press the Enter-button in order to select the desired menu. You can change

the selection by pressing Up or Down.Confirm every selection by pressing the Enter-button. You can

leave every mode by pressing the Mode/Esc-button. The functions provided are described in the

following setting.

MENU MAP

The device has two operation modes. It can be operated in Stand Alone or inDMX controlled.

When in Master/Slave Synchronization Mode, only one in a series chain can be set as the master.

ST.00Adjust strobe effect from 0~20

F.000 Adjust electronic zoom

AUTO AT

PR FromAT01 toAT10 with 10 different auto mode in zoom

From PR01 to PR10 with 10 different mode in zoom

SOUD MOD1 Sound control with color change in zoom

MOD2 Sound control with color strobe in zoom

RUN DMX and SLAV mode for selection

DMX Adjust DMX value from 001 to 512

PERS

STAG Run stage mode ,12 channel with details on dmxprotocol

ARC.1 Run 3 channel mode Red/Green/Blue

AR1.dRun 4 channel mode Dimmer/Red/Green/Blue

AR1.S Run 5 channel mode Dimmer/Red/Green/Blue/Strobe

HSV. Adjust Color in Hue (0~255),Saturation (0~255)and Value (0~255)

ID ID01 to ID66 to set different fixture

TEMP CURR show current fixture temperature

EDIT

PR.01 to PR.10 to set 10 programmer

SC.01 to SC.30 to set 30 different sense

R.000 Adjust red color from 0~255

G.000 Adjust green color from 0~255

B.000 Adjust blue color from 0~255

ST.00 Adjust strobe effect from 0~20

T.000 Adjust from 0~255

F.000 Adjust from 0~255

M.000 Adjust electronic zoom

SET

UPLD sending data to next fixture with self-built inprogram

REST reset fixture

RGB

POW

DIM

OFF/ON

HIGH/NORM select different power consumption with HIGH 100% and Norm 33%

OFF/DIM1/DIM2/DIM3/DIM4

CAL 1 White balance adjustment

WT01 to WT.11to adjust R/G/B from 0~255

Ps: when run STAGmode, channel 5 can show 11 different white color

CAL 2 RGB adjust correct color for RGB

RGB adjust from 25~255

STAT

R.000 Adjust red color from 0~255

G.000 Adjust green color from 0~255

B.000 Adjust blue color from 0~255

Master/slave mode (auto-running,sound control)

This mode will allow you to link up 32 units together without a controller.

Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the units.

For proper performance it may be necessary to use a terminator at the last fixture.

DMX-Protocol

Channel Value Function

1Dimmer

0-100% dimmer

0-255

2Red

0-100% Red

0-255

3Green

0-100%Green

0-255

4Blue

0-100% Blue

0-255

50-30

Color Change

No function

Color change in auto

31-255

60-10

Strobe

No function

Strobe with increasing speed

11-255

0-20

Built-in program

No function

Built-in program 1-10

Sound control

21-220

221-255

Speed for built-in program

Speed from slowly to fast

0-255

0-9

Dimmer optional (1st channel dimmer to be open)

Dimmer speed

No function

Dimmer 1

Dimmer 2

Dimmer 3

Dimmer 4

10-29

30-69

70-129

130-189

190-255

10 Zoom

0-100% electric zoom

0-255

11 Zoom speed

0-255 Adjust zoom speed with decreasing speed

ID selection (After select the fixture per ID1~ID66, control via

DMX when open value as below per each model even they are

at same DMX value)

No function

Each 10 value with a ID from ID1 until ID19

Each value with a ID from ID20 until ID66

0-9

10-210

211-255

TECHNICIAL SPECIFICATIONS

Model PARC-150ZOOM

Voltage ~ 230 V/ 50 Hz

Power consumption 180 VA

LED 150 W RGB COB LED

Gross Weight 4.9 kg

Dimensions W30x H37x D30 cm

MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany

www.monacor.com

01.27.04.2017

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IMG STAGE LINE DJ-Equipment Handbücher

IMG STAGE LINE

IMG STAGE LINE PARL-102 DMX Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE TWIST-95ZOOM Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE TWIST-20LED Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE MPX-2005 Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE BM-100 Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE ODP-361RGB Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE LED-640RGBW Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE PAR-16M/CR Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE LED-8C Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE PARL-12 RGBW Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE PARL- 40 SET Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE MULTI RAY LED-812DMX Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE Leuchtkraft ODC-100/CTW Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE FXBAR-5SET Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE MOVING HEAD TWIST-150 Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE LITEBOX-10 Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE MXR-4 Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE MPX-44/SW Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE PAR-16/CR Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE DIB-102 Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE MINIZOOM-712 Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE PARL-20DMX Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE STROBE-324LED Bedienungsanleitung

IMG STAGE LINE

IMG STAGE LINE LE-210 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung