Impact WM-SB Bedienungsanleitung

WM-SB

Wall Mount Scissor Boom

INSTRUCTIONS

Introduction

Thank you for choosing Impact.

The Impact WM-SB is a pantograph-style boom that supports lights and

accessories up to 11 pounds by moving your gear off the oor to minimize

clutter and save space. This boom arm can be mounted to masonry or wood

walls and features robust steel construction for a solid and dependable hold.

The pantograph has a 31-inch height adjustment range and a 55-inch maximum

length. The riser has a 13-inch height adjustment range and the pantograph can

swivel 180° for ideal light and accessory placement. Large ergonomic locking

T-handles give you a good grip for plenty of torque when adjusting length, height,

and swivel.

Precautions ⚠⚡

• Please read and follow these

instructions, and keep this manual

in a safe place.

• Clean the unit with only a soft, dry

cloth.

• Make sure that this product

is intact and that there are no

missing parts.

• Do not exceed the maximum load

capacity.

• The included hardware of this

product has been designed

specically for mounting directly

on concrete walls; depending on

wall type and material, the use of

additional appropriate mounting

hardware and/or accessories

such as heavy-duty anchors may

be required.

• When installing this product,

be sure to refer to the mounting

instructions detailed in this

manual; failure to abide by the

mounting instructions may void

the product’s warranty.

• It is recommended that at least

2 people perform the installation

process to prevent injury from

mishandling or dropping the

product.

• Be careful not to catch or pinch

your ngers when adjusting the

pantograph’s length and height.

• Always make sure the load is

supported when loosening any of

the locks to adjust the height or

length of the pantograph and riser.

• All images are for illustrative

purposes only.

Type Wall-mount boom

Reach from Mount Up to 55 in. (139.7 cm)

Vertical Adjustment 31 in. (78.7 cm)

Swivel 180°

Riser Height Adjustment Up to 13 in. (33 cm)

Mount 5/8 in. stud with 3/8-16 top

Material Steel

Dimensions (L × W × H) 51 × 9.5 × 4.8 in.

(129.5 × 24.1 × 12.2 cm)

Weight 17.7 lb. (8 kg)

Specications

Overview

1. Mounting plate

2. Pull lock

3. Locking collar

4. Pantograph

5. 5/8 in. pin with 3/8-16 top

6. Riser

7. Riser height lock

8. Riser pull lock

Also Included:

• Masonry wall anchors (×8)

7.5mm mounting holes.

5.5mm mounting holes.

Setup

1. Use the mounting plates as

templates to mark the large drilling

holes for the wall anchors.

2. Use a 1/2-inch (12 mm) masonry

drill bit to predrill the marked spots

2 inches (51 mm) deep. Then clean

out the debris from the holes.

3. If necessary, use a hammer to

gently tap the anchors into the

holes so the bolt protrudes from

the hole and the expansion sleeve

is no longer visible.

4. Remove the nut, locking washer,

and at washer from the anchors,

and place the WM-SB’s mounting

plates onto the bolts.

5. Replace the at washers on

the bolts rst, then the locking

washers, and the nut. Use a

wrench to tighten the nut until

secure.

Attaching the WM-SB to a Concrete Wall

Caution! Make sure the concrete wall or block is solid and at least 6 inches

thick. If the concrete exhibits cracks or other defects, this may result in failure

of the concrete anchors and cause personal injury or damage your mounted

equipment.

Warning! Do not drill into the mortar between concrete blocks.

Tip: Use a bubble level to ensure the

WM-SB is straight. 1

4 5

Setup

Attaching the WM-SB to a Wood Wall or Surface

Height Adjustment

1. Use the mounting plates as

templates to mark the small

drilling holes

2. Hold the WM-SB in place and

drill in four wood screws in both

mounting plates.

Pantograph:

Loosen the pull lock and the locking

collar, and slide the pantograph to the

desired height. Make sure the locking

collar is ush with the bottom of the

pantograph, and tighten the locks until

secure.

Riser:

Loosen the riser height lock, and

adjust the riser. Then tighten the riser

height lock until secure.

Length Adjustment

Angle Adjustment

Mounting Devices to the WB-SB

Loosen the pull lock and the riser

pull lock to adjust the length of the

pantograph. Make sure both locks

are securely tightened before you

continue.

To adjust the angle from the wall,

loosen the pull lock, and rotate the

pantograph into position. Then tighten

the pull lock until secure.

The WM-SB can accommodate light

xtures and accessories with a 5/8-

inch receiver or 3/8-16 socket.

To mount devices with a 1/4-20 socket,

use a 3/8-16 female to 1/4-20 male

adapter (available separately).

One-Year Limited Warranty

This Impact product is warranted to the original purchaser to be free from defects

in materials and workmanship under normal consumer use for a period of one

(1) year from the original purchase date or thirty (30) days after replacement,

whichever occurs later. The warranty provider’s responsibility with respect

to this limited warranty shall be limited solely to repair or replacement, at the

provider’s discretion, of any product that fails during normal use of this product in

its intended manner and in its intended environment. Inoperability of the product

or part(s) shall be determined by the warranty provider. If the product has been

discontinued, the warranty provider reserves the right to replace it with a model

of equivalent quality and function.

This warranty does not cover damage or defect caused by misuse, neglect,

accident, alteration, abuse, improper installation or maintenance. EXCEPT AS

PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS

WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED

TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. This warranty provides you with specic legal rights, and

you may also have additional rights that vary from state to state.

To obtain warranty coverage, contact the Impact Customer Service Department

to obtain a return merchandise authorization (“RMA”) number, and return the

defective product to Impact along with the RMA number and proof of purchase.

Shipment of the defective product is at the purchaser’s own risk and expense.

For more information or to arrange service, visit www.impactstudiolighting.com

or call Customer Service at 212-594-2353.

Product warranty provided by the Gradus Group.

www.gradusgroup.com

Impact is a registered trademark of the Gradus Group.

GG2

Inhaltsverzeichnis

Andere impact Rack & Stand Handbücher

impact

impact BP-RA-MBH Bedienungsanleitung

impact

impact BDA-BRO-L Bedienungsanleitung

impact

impact LS-CS40MK Bedienungsanleitung

impact

impact LSP-SW10S Bedienungsanleitung

impact

impact LS-CT40M Bedienungsanleitung

impact

impact BG-PS440 Bedienungsanleitung

impact

impact LSA-WMB4HD Bedienungsanleitung

impact

impact LSA-LW22P Bedienungsanleitung

impact

impact LS-CL40M Series Bedienungsanleitung

impact

impact LS-CT20MK Bedienungsanleitung

impact

impact LS-CS40M Bedienungsanleitung

impact

impact LS-CB6 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung

impact WM-SB Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken