Impex APEX Bedienungsanleitung

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

Model

APEX

Retain This

Manual for

Reference

06-24-02

OWNER'S

MANUAL

MARCY HOME GYM

APEX

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: (800) 999-8899 Fax: (626) 961-9966

www.impex-fitness.com

[email protected]

TABLE OF CONTENTS

BEFORE YOU BEGIN....................................................................................……….. 1

IMPORTANT SAFETY NOTICES...................................................................……….. 2

HARDWARE IDENTIFIER.....….....................................................................……….. 3

ASSEMBLY INSTRUCTIONS.........................................................................……….. 4

PARTS LIST…………………………………………………………………………………...14

WARRANTY.................................................................................................…………. 15

ORDERING PARTS.......................................................................................…………15

BEFORE YOU BEGIN

Thank you for selecting the MARCY APEX HOME GYM by IMPEX FITNESS

PRODUCTS. For your safety and benefit, read this manual carefully before using

the machine. As a manufacturer, we are committed to provide you complete

customer satisfaction. If you have any questions, or find there are missing or

damaged parts, we guarantee you complete satisfaction through direct

assistance from our factory. To avoid unnecessary delays, please call our TOO-

FREE customer service number. Our Customer Service Agents will provide

immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST

www.impex-fitness.com

[email protected]m

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply

whenever you operate a piece of exercise equipment. Be sure to read the entire manual

before you assemble or operate your machine. In particular, note the following safety

precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal

symptoms, STOP the workout at once. CONSULT A PHYSICIAN

IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine

near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear

robes or other clothing that could become caught in the machine. Running

or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO

NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or

physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to

properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR

PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE

AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL

INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.

ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY

DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.

NOTE: It is strongly recommended this machine to be assembled by two or more people to

avoid possible injury.

STEP 1 (See Diagram 1)

A.) Place the Base Frame (#1) on the floor. Attach two Foot Plates (#30) to the front of the Base

Frame (#1). Align the holes and secure it with two M10 x 3” Hex Bolts (#66), four ∅13/16” Flat

Washers (#75), and two M10 Aircraft Nuts (#78). NOTE: DO not tighten all the nuts and bolts

yet. Only finger-tighten them for now.

B.) Attach the Rear Base Frame (#6) and the Rear Vertical Frame (#5) to the back of the Base

Frame (#1). Align the holes and secure it with two M10 x 3” Hex Bolts (#66), four ∅13/16” Flat

Washers (#75), and two Aircraft Nuts (#78).

C.)Attach the Front Vertical Frame (#3) to the Base Frame (#1). Secure it with two M10 x 3” Hex

Bolts (#66), four ∅13/16” Flat Washers (#75), and two M10 Aircraft Nuts (#78).

D.)Attach the Upper Frame (#2) to the top of the Front Vertical Frame (#3). Secure it with two

M10 x 3” Hex Bolts (#66), four ∅13/16” Flat Washers (#75), one 2” x 6 5/16” Bracket (#4) and

two M10 Aircraft Nuts (#78).

E.) Attach the Upper Frame (#2) to the top of Rear Vertical Beam (#5). Secure it with one M10 x 2

9/16” Hex Bolt (#67), one M10 x 3” Hex Bolt (#66), three ∅13/16” Flat Washers (#75), one 2”

x 4” Bracket (#28), and one M10 Aircraft Nut (#78).

STEP 2 (See Diagram 2)

A.) Place two Rubber Bumpers (#37) onto the Base Frame (#1). Align the two holes and push

two Weight Plate Guide Rods (#23) through the Bumpers into the Base Frame.

B.) Slide fourteen Selective Weight Plates (#84) from top of the Guide Rods (#23) down to the

Base Frame (#1). NOTE: The grove on the Plates should always face down and toward the

left side of the machine. Insert the Selecting Rod (#22) into the center hole on the Plates.

Slide the Selector Stem (#46) and the Top Weight Plate (#83) onto the Guide Rods. Align

the hole and secure the Selector Stem (#46) to the Selecting Rod (#22) with a M10 x 1 9/16”

Socket Bolt (#82).

C.)Attach the Top Socket Assembly (#7) to the top of the Weight Plates Guide Rods (#23).

Secure it to the Upper Frame (#2) with two M10 x 3” Hex Bolts (#66), four ∅13/16” Flat

Washers (#75), one 2” x 4 ¾” Bracket (#29), and two M10 Aircraft Nuts (#78).

D.)Secure the Top Socket Assembly (#7) to the Weight Plates Guide Rods (#23) with two M6 x

5/8” Allen Bolts (#73).

STEP 3 (See Diagram 3)

A.) Attach the Butterfly Support (#13) and the Butterfly Pulley Frame (#15) to the Front Vertical

Frame (#3). Secure them with two M10 x 3” Hex Bolts (#66), four ∅13/16” Flat Washers

(#75), and two M10 Aircraft Nuts (#78).

B.) Attach a 2” Square Rubber Cap (#53) to the opening underneath the Butterfly Support (#13).

See A View.

C.) Place a Butterfly Cable Guide (#14) onto the axle on the Right Butterfly (#12). Insert the

Right Butterfly through the hole on the Butterfly Support (#13). Secure it with a ∅1 ½”

Washer (#32), M12 Aircraft Nut (#77), and M12 Cone Shape Cap (#52).

D.) Attach a Butterfly Pad (#41) to the Right Butterfly (#12) and secure it with two M8 x 2 9/16”

Allen Bolts (#71) and two ∅11/16” Flat Washers (#76).

E.) Repeat the above procedure C and D to install the other side. DIAGRAM 3

STEP 4 (See Diagram 4)

A.) Attach the Leg Developer Holder (#17) to the Front Vertical Frame (#3). Secure it with two

M10 x 3” Hex Bolts (#66), four ∅13/16” Flat Washers (#75), one 2” x 4 ¾” Bracket (#29),

and two M10 Aircraft Nuts (#78).

B.) Attach the Short Quick Release Pin (#34) to the Leg Developer Holder (#17).

C.)Attach the Seat (#39) to the Seat Support (#18). Secure it with two ∅11/16” Flat Washers

(#76), and two M8 x 2 9/16” Allen Bolts (#71).

D.)Attach the Seat Support (#18) to the Leg Developer Holder (#17). Pull the Short Quick

Release Pin (#34) to adjust the height of the Seat.

E.) Insert a Foam Roll Tube (#42) halfway through the hole on Leg Developer Holder (#17).

Push two Foam Rolls (#43) onto the Tube from both ends. Push two ∅3” Round Plugs (#59)

onto both ends of the Tube.

F.) Attach the Backrest Support Frame (#19) to the Front Vertical Frame (#3). Secure it with two

M10 x 3” Hex Bolts (#66), four ∅13/16” Flat Washers (#75), one 2” x 4 ¾” Bracket (#29),

and two M10 Aircraft Nuts (#78).

G.)Attach the Short Quick Release Pin (#34) to the Backrest Support Frame (#19).

H.)Attach the Backrest (#40) to the Backrest Adjustment Tube (#20). Secure it with two ∅

11/16” Flat Washers (#76) and M8 x 5/8” Allen Bolts (#72). Insert the Backrest Adjustment

Tube (#20) into the Backrest Support Frame (#19). Pull out the Quick Release Pin (#34) to

adjust the Backrest position. DIAGRAM 4

STEP 5 (See Diagram 5)

A.) Insert a ∅5/8” x 9 3/8” Axle (#31) halfway through the hole on the Base Frame (#1).

B.) Attach the Front Press Left Base (#9) and the Front Press Right Base (#10) onto the

Axle (#31) from both sides. Secure the Axle with two ∅13/16” Flat Washers (#75), M10

Aircraft Nuts (#78), and M10 Cone Shape Caps (#51).

C.)Attach the Front Press (#8) to the Front Press Base (#9 & #10). Secure it with one M10

x 3” Hex Bolt (#66), one M10 x 2 9/16” Hex Bolt (#67), three ∅13/16” Flat Washers

(#75), one 2” x 4” Bracket (#28), and one M10 Aircraft Nut (#78) on each side of the

Front press.

D.)Lubricate the inside of the Foam Grips (#44) with water and slide them onto the

handlebars on the Front Press.

E.) Attach the Leg Developer (#16) to the Leg Developer Holder (#17). Secure it with one

M12 x 3 3/8” Hex Bolt (#64), two ∅1” x ∅½” Bushings (#80), two ∅15/16” Flat

Washers (#74), and one M12 Aircraft Nut (#77).

F.) Insert a Foam Roll Tube (#42) halfway through the hole on the Leg Developer (#16).

Push two Foam Rolls (#43) onto the Tube from both ends. Push two ∅3” Round Plugs

(#59) onto both ends of the Tube.

G.)Insert an L Shape Pin (#35) through the hole on the Leg Developer (#16) to lock it in

place. Remove the Pin when using the Leg Developer.

DIAGRAM 5

STEP 6 (See Diagram 6)

A.) Attach one end of the 82” Butterfly Cable (#47) to the Butterfly Cable Guide (#14). Secure

it with one M10 x 1” Hex Bolt (#70), two ∅13/16” Flat Washers (#75), and one M10

Aircraft Nut (#78). (See A Detail)

B.) Draw the Cable (#47) to the bracket underneath the Butterfly Pulley Frame (#15). Attach

Pulley (#60) and two Pulley Covers (#61) to the Cable. Align the hole on the Pulley to the

bracket and secure it with one M10 x 1 ¾” Hex Bolt (#69), two ∅13/16” Flat Washers

(#75), and one M10 Aircraft Nut (#78).

C.)Pull the Cable downward and attach a Pulley (#60) and two Pulley Covers (#61) in the

mid-span. Attach a Single Floating Pulley Bracket (#21) to the Pulley and secure it with

one M10 x 1 ¾” Hex Bolt (#69), two ∅13/16” Flat Washers (#75), and one M10 Aircraft

Nut (#78). Let the Single Floating Pulley Bracket (#21) hanging for now.

D.)Draw the Cable upward to the Butterfly Pulley Frame (#15) and install another Pulley.

E.) Attach the other end of the Cable to the other Cable Guide.

DIAGRAM6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Impex Heim-Fitnessstudio Handbücher

Impex

Impex APEX TSA-499 Bedienungsanleitung

Impex

Impex Circuit Fitness AMZ-600CG Bedienungsanleitung

Impex

Impex MARCY DIAMOND ELITE MD-2080 Bedienungsanleitung

Impex

Impex JD-1.2 Bedienungsanleitung

Impex

Impex MARCY DELUXE SM-5870 Bedienungsanleitung

Impex

Impex PM-4400 Bedienungsanleitung

Impex

Impex MARCY SM-1000 Bedienungsanleitung

Impex

Impex Marcy SB-350 Bedienungsanleitung

Impex

Impex MARCY MWB 758 Bedienungsanleitung

Impex

Impex POWERHOUSE SM 3000 Bedienungsanleitung

Impex

Impex MARCY CLUB MKM-81010 Bedienungsanleitung

Impex

Impex MARCY MWM-7041 Bedienungsanleitung

Impex

Impex Marcy SB-662 Bedienungsanleitung

Impex

Impex MWB-50100 Bedienungsanleitung

Impex

Impex TR-2 Bedienungsanleitung

Impex

Impex Circuit Fitness AMZ-986RW Montage- und Bedienungsanleitung

Impex

Impex Olympic Cage Bedienungsanleitung

Impex

Impex Marcy SB-512 Bedienungsanleitung

Impex

Impex MARCY MWM-7150 Bedienungsanleitung

Impex

Impex MARCY PLATINUM MP 1105 Bedienungsanleitung

Impex

Impex MARCY MWB-544 Bedienungsanleitung

Impex

Impex MWB-715N Bedienungsanleitung

Impex

Impex IRON GRIP STRENGTH TSA-5761 Bedienungsanleitung

Impex

Impex ADI-5100-I Bedienungsanleitung

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Weider

Weider 8300 Hard Drive Bedienungsanleitung

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Weider

Weider 8700 I Kurzanleitung

Bowflex

Bowflex Sport 001-6961 Bedienungsanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Weider

Weider WEMC10161 Bedienungsanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

cardiobull

cardiobull RA17 Bedienungsanleitung

ParaBody

ParaBody 40 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung