InFocus IN42 Leitfaden

Andere Handbücher für IN42

4

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere InFocus Projektorzubehör Handbücher

InFocus

InFocus SP777 Bedienungsanleitung

InFocus

InFocus SP-CEIL-012 Bedienungsanleitung

InFocus

InFocus LP70+ Leitfaden

InFocus

InFocus SP-CEIL-008 Bedienungsanleitung

InFocus

InFocus LNS-W01 Leitfaden

InFocus

InFocus LP130 Leitfaden

InFocus

InFocus SP-CEIL-003 Bedienungsanleitung

InFocus

InFocus SP-LAMP-088 Leitfaden

InFocus

InFocus SP-LAMP-092 Leitfaden

InFocus

InFocus RPM A-C Bedienungsanleitung

InFocus

InFocus LiteShow 4 DB+ Bedienungsanleitung

InFocus

InFocus SP-LAMP-080 Leitfaden

InFocus

InFocus SP-CEIL-006 Bedienungsanleitung

InFocus

InFocus SP-LAMP-090 Leitfaden

InFocus

InFocus LP 240 Bedienungs- und Sicherheitshinweise

InFocus

InFocus LiteShow network adapter Bedienungsanleitung

InFocus

InFocus LiteProLS Bedienungsanleitung

InFocus

InFocus WT96 Bedienungsanleitung

InFocus

InFocus SP-CEIL-001 Bedienungsanleitung

InFocus

InFocus SP-LAMP-073 Leitfaden

InFocus

InFocus CableWizard SP-CW3 Kurzanleitung

InFocus

InFocus SP-CEIL-010 Bedienungsanleitung

InFocus

InFocus LP 650 Leitfaden

InFocus

InFocus LITESHOW4 DB+ Bedienungsanleitung

Beliebte Projektorzubehör Handbücher anderer Marken

Optoma

Optoma BX-AL133B Bedienungsanleitung

PEERLESS

PEERLESS PE 1120 Leitfaden

Osram

Osram SIRIUS HRI Series Handbuch

Presentation Switchers

Presentation Switchers PS111 Bedienungsanleitung

Kramer

Kramer VIA GO Bedienungsanleitung

Yamaha

Yamaha PJL-112 Stücklistenhandbuch

Swedstyle

Swedstyle CL23AA02ZA25E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 236CB Betriebsanleitung

Epson

Epson BrightLink 475Wi Bedienungsanleitung

Acer

Acer WP100 Bedienungsanleitung

i3

i3 i3board Bedienungsanleitung

CHIEF

CHIEF HB-43E Bedienungsanleitung

Biamp

Biamp Modena Hub Service-Handbuch

NEC

NEC MP10RX Bedienungsanleitung

Panamorph

Panamorph DCR-S3 Bedienungsanleitung

Exact solutions

Exact solutions FRAME-EVO-P10 Bedienungsanleitung

CHIEF

CHIEF VCM103S Bedienungsanleitung

Sharp

Sharp AN-PH20EZ Bedienungsanleitung

34

Replacing the projection lamp

The lamp hour timer in the Service Info menu counts the number of hours

the lamp has been in use. Twenty hours before the specified end of the

lamp’s life, the message “Change lamp” briefly appears on the projected

screen.

NOTE: You can order new lamp housings from www.infocus.com (in select

areas), your retailer or your dealer. Use only a replacement lamp with the

same type and rating as the original lamp.

The part number is SP-LAMP-027.

1Turn off the projector and unplug the power cable.

2Wait 45 minutes to allow the projector to cool thoroughly.

3Loosen the lamp cover screw on the right side of the projector (marked

by the arrow) then slide and lift the lamp cover off.

WARNINGS:

• To avoid burns, allow the projector to cool for at least 45 minutes before

you replace the lamp.

• Do not drop the lamp module. The glass may shatter and cause injury.

Do not touch the glass lamp screen. Fingerprints can obscure projection

sharpness.

• Be extremely careful when removing the lamp housing. In the unlikely

event that the bulb ruptures, small glass fragments may be generated.

The lamp housing is designed to contain these fragments, but use cau-

tion when removing the lamp housing. Before replacing the lamp, clean

the lamp compartment and dispose of cleaning materials. Wash hands

after lamp replacement. This product has a lamp which contains a very

small amount of mercury. Dispose of it as required by local, state or fed-

eral ordinances and regulations. For more information see

www.eiae.org.

Service Info menu

turn off and unplug

the projector

wait 45 minutes

lamp cover screw

EDX Ref Guide.fm Page 34 Friday, June 30, 2006 10:48 AM

35

4Loosen the three captive screws (marked by the arrows) on the lamp

module.

5Carefully remove the lamp module by grasping and lifting the handle.

Dispose of the lamp in an environmentally proper manner.

6Install the new lamp module, making sure that it is properly seated, and

tighten the three captive screws.

7Replace the cover over the lamp module by sliding it back into place and

tightening the screw.

8Plug in the power cable, press the power switch then press the Power

button to turn the projector back on. Reset the lamp hour timer by navi-

gating to the Settings>Service menu and selecting Reset Lamp Hours.

loosen the captive screws on lamp module

lamp module handle

reset lamp hours in Service menu

EDX Ref Guide.fm Page 35 Friday, June 30, 2006 10:48 AM