InFocus LP 600 Bedienungsanleitung
LP®600
USER’S GUIDE
6653_LP600_UG.qxd 4/2/04 2:14 PM Page 1
2
Declaration of Conformity
Manufacturer: InFocus Corporation, 27700B SW Parkway Avenue, Wilsonville,
Oregon 97070 USA
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
We declare under our sole responsibility that this projector conforms to the following
directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
May, 2004
Trademarks
Microsoft, PowerPoint, Word, Excel and Windows are trademarks or registered trade-
marks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered
trademarks of Adobe Systems Incorporated. InFocus, LiteShow, LitePort, and LP are
trademarks or registered trademarks of InFocus Corporation.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is oper-
ated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruc-
tion manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference,
in which case the user may be required to take adequate measures. The typical use is
in a conference room, meeting room or auditorium.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Agency Approvals
UL, CUL, TUV, GOST
Other specific Country Approvals may apply, please see product certification label.
This user’s guide applies to models LP600 and GEN205.
InFocus reserves the right to alter product offerings and specifications at any time.
3
Table of Contents
Introduction 5
Connecting a computer 7
Required computer connections 7
Displaying a computer image 9
First-time projector use with Windows 98 10
Adjusting the image 12
Connecting a video device 13
Displaying a video image 14
Shutting down the projector 16
Troubleshooting your setup 16
Using the keypad buttons 25
Using the remote control 26
Using the LitePort player 27
Using the audio 28
Optimizing computer images 29
Presentation features 29
Optimizing video images 29
Customizing the projector 29
Using the menus 30
Picture menu 31
Settings menu 34
Maintenance 39
Cleaning the lens 39
Using the security lock 39
Replacing the projection lamp 40
Cleaning the lamp filter screens 42
Appendix 43
Accessories 43
Red LED behavior and projector errors 44
Projected image size 44
If you are experienced in setting up presentation systems, use the included
Quick Set Up card. For complete details on connecting and operating the
projector, refer to this User’s Guide. Electronic versions of this User’s Guide
in multiple languages are available on the included CD. The most current
versions can be found on our website.
The website also has technical specifications (an interactive image size cal-
culator, laptop activation commands, connector pin outs, a glossary, the
product data sheet), a web store to buy accessories, and a page for online
registration. See the inside of the back cover for a list of all relevant web
addresses.
4
Important Operating Considerations for Safety
• Place the projector in a horizontal position no greater than 15 degrees
off axis.
• Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
• Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
• Use only InFocus-approved ceiling mounts.
• Use only the power cord provided. A surge-protected power strip is
recommended.
• Refer to this manual for proper startup and shutdown procedures.
• In the unlikely event of the lamp rupturing, discard any edible items
placed in the surrounding area and thoroughly clean the area along all
sides of the projector. Wash hands after cleaning the area and handling
the ruptured lamp. This product has a lamp which contains a very
small amount of mercury. Dispose of it as required by local, state or fed-
eral ordinances and regulations. For more information see
www.eiae.org.
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty section at
the end of this user's guide.
2 ft (.6m)
Do not place objects or people in the 2 foot (.6m) area along the side of the projector.
For ceiling mount applications, this area should be 5 feet (1.5m).
5 ft (1.5m)
5
Introduction
Your new digital projector provides computer and video inputs and has
XGA 1024x768 resolution. The projector is easy to connect, easy to use, and
easy to maintain. An Interactive Display on the top of the projector gives
you constant feedback on the status of the projector.
Online Registration
Register your projector on our website to receive product updates,
announcements, and registration incentives. See the inside of the back cover
for the web address.
Included items
*The lens cap tether ships in the Documentation Pack. Attach it to the lens cap and
the projector if desired.
Projector components and features
documentation
remote
computer
cable
projector
lens cap
power
cable
video cable
audio cable
carry case
lens cap tether*
audio cable
adapter
keypad
speaker
zoom
focus
elevator foot release
remote
control
receiver (IR)
connectors
leveling
foot
heat vent
Interactive display
IR receiver
IR receiver
6
Connector Panel
The projector provides computer and video connectors:
• one M1-D/A (HD, DVI, and computer)
• one VESA (HD, HD component, and computer)
• one S-video
• one composite RCA video
• one audio in/one audio out
It also has an RS-232 serial connector for serial control. The Command Line
Interface (CLI) specifications and commands are on our website.
The projector also has a LitePortTM USB connector (Type A) and player for
JPEG (Joint Photographic Experts Group, .jpg, .jpe, or .jpeg) images. This
allows you to display any JPEG image automatically, without a computer
connected. Use your own JPEGs from your digital camera, or convert your
files, such as Microsoft PowerPointTM, WordTM, or ExcelTM files, into
JPEGs using LitePort Utility software (included on the CD), which allows
you to easily generate the highest quality JPEG images possible. Then trans-
fer the JPEG images from your computer to the projector using a USB mass
storage device and your images are ready to be displayed. (Please refer to
the Service and Support section of our website for advanced specifications
on the USB device and JPEG files.) You can use the remote control to select
which JPEGs to view (page 27) or you can set up the LitePort player using
the LitePort onscreen menu to select display preferences and automatically
display and advance your JPEGs (page 36).
Wireless Projection
You can use the projector’s M1 connector along with the InFocus
LiteShowwireless adapter and software for cable-free digital projection.
Contact an authorized InFocus dealer or visit the website listed on the back
inside cover of this User’s Guide for more information.
Connector panel
lock
power
connector
M1-D/A
s-video
composite
external
speaker
(audio out)
RS-232 serial control
video
computer
audio
VESA in/ USB JPEG
monitor out
7
Connecting a computer
Required computer connections
Connect the black end of the computer cable to the Computer 1 connector
on the projector. Connect the blue end to the video port on your computer. If
you are using a desktop computer, you first need to disconnect the monitor
cable from the computer’s video port.
Some Macintoshcomputers do not have a standard VESA-out video port.
If the supplied computer cable will not connect to your computer, purchase
the appropriate adapter from your Applereseller.
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
The Power LED on the projector’s keypad turns solid green.
NOTE: Always use the power cable that shipped with the projector.
Optional computer connections
To advance slides in a PowerPoint™ presentation using the remote, plug the
USB connector on the computer cable into the USB mouse connector on
your computer. USB drivers must be installed to use the USB feature. For
more information, see page 11.
To have sound with your presentation, connect the audio cable to your com-
puter and to the Audio In connector on the projector.
connect computer cable
connect power cable
connect computer cable
connect audio cable
8
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, plug the monitor cable
to the black Computer 2 connector on the projector. This connector can be
used as monitor out or VESA in. The default is VESA in, so you must
change this option in the menu to use monitor out. See page 34 to switch
between the two functions.
If you prefer connecting your projector to your computer with an optional
VESA cable, connect one end of the cable to the VESA port on your com-
puter, and connect the other end of the cable to the blue Computer 2 con-
nector on the projector.
This connector can be used as monitor out or VESA in. The default is VESA
in.
You can control the projector from an LCD control panel or computer by
connecting an RS-232 cable to the projector’s Serial Control connector. Spe-
cific RS-232 commands can be found in the Service and Support section of
our website.
You can play JPEGs using the LitePort USB connector and LitePort player.
You need a USB mass storage device to use this connector. See page 27 for
details.
connect monitor cable
connect VESA cable
connect RS-232 cable
connect USB mass storage device
9
Displaying a computer image
Remove the lens cap.
Press the Power button on the top of the projector or the remote.
The LED flashes green and the fans start to run. When the lamp comes on,
the startup screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness. The Interactive Display on
the projector indicates the startup status.
? No startup screen? Get help on page 17.
Turn on your computer.
The computer’s image should appear on the projection screen. If it doesn’t,
press the Source button on the projector’s keypad.
Make sure your laptop’s external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/LCD
key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
labeled function key simultaneously. Refer to your laptop’s documenta-
tion to learn your laptop’s key combination.
? No computer image? Try pressing the Auto Image
button on the keypad. Get help on page 17.
remove lens cap
press Power button
turn on computer
activate laptop’s external port
10
First-time projector use with Windows 98
If you are running Windows 2000, Windows ME, or Window XP, skip these
steps and go to “Adjusting the image” on page 12.
The first time you connect a computer running Windows 98 to the projector,
the computer recognizes the projector as “new hardware” and the Add
New Hardware Wizard appears. Follow these instructions to use the Wiz-
ard to load the correct driver (which was installed with your Windows
operating system).
aClick Next to begin searching for the driver.
bMake sure “Search for the best driver” is selected, then click Next.
cUncheck any checked boxes, then click Next. Windows automatically
locates the driver. If this driver has been removed, reload the driver using
your Windows operating system CD.
dWhen Windows finds the driver, you are ready to install it. Click Next.
a
b
c
d
Andere Handbücher für LP 600
6
Inhaltsverzeichnis
Andere InFocus Projektor Handbücher
InFocus
InFocus RP10S Bedienungsanleitung
InFocus
InFocus LP930 Bedienungsanleitung
InFocus
InFocus IN2112 Bedienungsanleitung
InFocus
InFocus Work Big IN15 Bedienungsanleitung
InFocus
InFocus IN3914 Bedienungsanleitung
InFocus
InFocus IN146 Bedienungsanleitung
InFocus
InFocus IN134UST Bedienungsanleitung
InFocus
InFocus LP 120 Bedienungsanleitung
InFocus
InFocus X3 Bedienungsanleitung
InFocus
InFocus LP690 Bedienungsanleitung
InFocus
InFocus C110 Bedienungsanleitung
InFocus
InFocus LP 740 LiteMount Bedienungsanleitung
InFocus
InFocus IN3124 Bedienungsanleitung
InFocus
InFocus LitePro Bedienungsanleitung
InFocus
InFocus LP630 Bedienungsanleitung
InFocus
InFocus Learn Big IN3102 Bedienungsanleitung
InFocus
InFocus ScreenPlay 5700 Bedienungsanleitung
InFocus
InFocus SP777 Systemhandbuch
InFocus
InFocus SP4800 Handbuch
InFocus
InFocus LitePro 610 Bedienungsanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
