InFocus SP5700 Bedienungsanleitung

ENGLISH

Declaration of Conformity

Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon

97070 USA

European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands

We declare under our sole responsibility that the ScreenPlay 5700 projector conforms

to the following directives and norms:

EMC Directive 89/336/EEC, Amended by 93/68/EEC

EMC: EN 55022

EN 55024

EN 61000-3-2

EN 61000-3-3

Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC

Safety: EN 60950: 2000

May, 2003

Trademarks

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple

Computer, Inc. IBM is a trademark or registered trademark of International Business

Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered

trademarks of Microsoft Corporation. Digital Light Processing is a trademark or reg-

istered trademark of Texas Instruments. Faroudja, DCDi, and TrueLife are trade-

marks or registered trademarks of Faroudja. InFocus and ScreenPlay are trademarks

or registered trademarks of InFocus Corporation.

FCC Warning

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by InFocus Corporation can void

the user's authority to operate the equipment.

Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Agency Approvals

UL, CUL, TÜV, NOM, IRAM, GOST, CCC, MIC, C-Tick

Table of Contents

Introduction 3

Positioning the projector 5

Video connections 6

Connecting a video device 7

Displaying a video image 8

Connecting a computer 10

Shutting down the projector 11

Troubleshooting your setup 11

Using the keypad buttons 18

Using the remote control 19

Optimizing video images 20

Customizing the projector 20

Using the menus 21

Picture menu 22

Settings menu 27

Maintenance 29

Cleaning the lens 29

Replacing the projection lamp 30

Appendix 32

Specifications 32

Accessories 32

Red LED behavior and projector errors 33

Projected image size 33

Source compatibility 34

Projector dimensions for ceiling mount installations 35

RS-232 terminal specifications 36

For complete details on connecting and operating the projector, refer to this

User’s Guide. Electronic versions of this User’s Guide in multiple languages

are available on our website at www.infocushome.com/support.

The website also has technical specifications (an interactive image size cal-

culator, laptop activation commands, connector pin outs, a glossary, the

product data sheet), a web store to buy accessories, and a page for online

registration.

Important Operating Considerations

Do not place the projector on a tablecloth or other soft covering that may

block the vents. Vents are placed along the left and right sides of the projec-

tor, as well as across the front of the projector. Do not use a non-approved

ceiling mount. In the unlikely event of the lamp rupturing, discard any edi-

ble items placed in the surrounding area and thoroughly clean the area

along the sides and in the front of the projector.

2 ft (.6m) 2 ft (.6m)

2 ft (.6m)

Do not place objects in the areas along the side and in the front of the projector

Introduction

Congratulations and thank you for your excellent choice of a superior digi-

tal image projection device. Your new ScreenPlay™ 5700 projector from

InFocus®is specifically designed for home cinema applications. The

ScreenPlay 5700 sets the standard for Enhanced-Definition digital perfec-

tion, featuring true Enhanced Definition 1024x576 resolution using the latest

DLP™ technology and new DCDi video processing from Faroudja™. Cali-

brated to D65 color mastering standards, the ScreenPlay 5700 reproduces

colors and details the way the director intended. Whether you are watching

movies or High Definition broadcasts or playing the latest video game, you

will enjoy breathtaking image quality.

Online Registration

receive product updates, announcements, and registration incentives.

Included items

Projector components and features

user’s guide, safety card

remote

projector

lens cap

power

cable*

SCART

cable

cable cover

keypad

zoom

focus

elevator foot release

remote

control

receiver (IR)

air intake

vent

I/O panel

leveling

foot

exhaust

heat vent

remote control

receiver (IR)

*country-dependent

Connector Panel

The projector provides eight discreet video connectors:

•twocomponentRCA

•twoS-video

•onecompositeRCA

• one M1-DA (HD, DVI, and computer)

• one VESA (HD, HD component, and computer)

•onecomponentD5

It also has a mini-jack input for a Niles or Xantech-compatible IR repeater

and an RS-232 connector for serial control. The Command Line Interface

(CLI) specifications and commands are listed in the Appendix starting on

page 36.

Two 3.5 mm mini-jack triggers provide 12 volt current. Trigger 1 provides a

constant output while the projector is on. If you connect your projection

screen to Trigger 1, when you turn on the projector the screen will move

down; when you turn the projector off, the screen will return to the storage

position. Trigger 2 provides a 4:3 aspect trigger. When you select 4:3 in the

Aspect Ratio menu or from the Resize button on the remote, a 12v signal

will be sent after a three second delay. Use this trigger for screens with 4:3

aspect curtains. When you switch back to 16:9 format, the curtains open to

reveal the entire screen.

For details on each connector type and their inputs, see page 34.

IR in

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1

trigger 2

component

s-video

video

component

lock

remote control

receiver (IR)

power

connector

s-video video

component

video

video/computer

1 & 2

serial

connector

video

IR input

12v triggers

screen trigger connection

3.5mm mono plug

+12v

ground

to screen relay (see screen manufacturer

for details)

Positioning the projector

There are a number a factors to consider when determining where to set up

the projector, including the size and shape of your screen, the location of

your power outlets, and the distance between the projector and the rest of

your equipment. Here are some general guidelines.

1Position the projector on a flat surface at a right angle to the screen.

The projector must be within 10 feet (3 m) of your power source. To

ensure adequate cable access, place the projector at least 6 inches

(0.15m) from a wall or other objects. Place the projector at least 5.6 feet

(1.7 m) from the projection screen.

If you install the projector on the ceiling, refer to the installation guide

that comes with the Ceiling Mount Kit for more information. To turn

the image upside down, see page 27. InFocus recommends use of an

authorized InFocus ceiling mount. The Ceiling Mount Kit is sold sepa-

rately, see page 32.

2Position the projector the desired distance from the screen.

The distance from the lens of the projector to the screen, the zoom set-

ting, and the video format determine the size of the projected image.

For more information about projected image sizes, see page 33.

The image exits the projector at a given angle. This image offset is 133%.

This means that if you have an image 10’ high, the bottom of the image will

be 3.3’ above the center of the lens.

Go to www.infocushome.com/support for a complete image size calcula-

tor.

lens center

bottom of image

3.3’ above lens

10’ high

image

Video connections

You can connect VCRs, DVD players, camcorders, digital cameras, video

games, HDTV receivers, and TV tuners to the projector. (You cannot directly

connect the coaxial cable that enters your house from a cable or satellite

company; the signal must pass through a tuner first. Examples of tuners are

digital cable boxes, VCRs, digital video recorders, and satellite TV boxes.

Basically, any device that can change channels is considered a tuner.) Audio

must be provided by your own speakers, as the projector has no separate

audio controls. If there is more than one output, select the highest quality

one. DVI, Component video and RGB (M1, HD15) have the best quality, fol-

lowed by S-video, and then composite video.

For a complete list of compatible sources, see page 34 of the Appendix.

Table 1: Video connections

Input signal Connector

Connector label

on projector

Standard Broadcast TV (not

HDTV), via cable, digital

cable, satellite TV, DirectTV

Component video

S-video

Composite video

Component 3, 6

S-video 4, 5

Video 7

HDTV Component video

VESA

DVI

Component 3, 6

VESA 2

M1-DA 1

DVD Component video

S-video

Composite video

Component 3, 6

S-video 4, 5

Video 7

VCR Composite video

S-video

Component video

Video 7

S-video 4, 5

Component 3, 6

Video Camera Composite video

S-video

Video 7

S-video 4, 5

Video Game VESA

Composite video

S-video

Component video

VESA 2

Video 7

S-video 4, 5

Component 3, 6

IR in

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1

trigger 2

component

s-video

video

component

s-video video

component

video

M1-DA VESA

Connecting a video device

If your video device has more than one output, select the highest quality

one. DVI video has the best quality, followed by Component video, S-video,

and then composite video.

If the video device uses component cable connectors, plug the cable’s green

connectors into the green component-out connector on the video device and

into the green component connector (labeled “Y”) on the projector. Plug the

component cable’s blue connectors into the blue component-out connector

on the video device and into the blue component connector (labeled “Pb”)

on the projector. Plug the component cable’s red connectors into the red

component-out connector on the video device and into the red component

connector (labeled “Pr”) on the projector.

If the video device uses a round, four-prong S-video connector, plug an

S-video cable into the S-video connector on the video device and into the S-

video connector on the projector.

If the video device uses a yellow composite video connector, plug a compos-

ite video cable’s yellow connector into the video-out connector on the video

device. Plug the other yellow connector into the yellow Video connector on

the projector.

If the video device uses a DVI connector, plug an M1-D cable into the video-

out connector on the video device. Plug the other connector into the M1-DA

connector on the projector.

If the video device uses a VESA connector, plug a VESA cable into the

video-out connector on the video device. Plug the other connector into the

VESA connector on the projector.

Connecting the power cable

Connect the power cable to the connector on the back of the projector and to

your electrical outlet. The Power LED on the keypad turns solid green.

NOTE: Always use the power cable that shipped with the projector.

connect component cable

IRin

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1

trigger 2

component

s-video

video

component

connect S-video cable

IRin

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1

trigger 2

component

s-video

video

component

connect composite video cable

IRin

Pr Pr

Pb Pb

serialcontrol

M1-DA vesa trigger1

trigger2

component

s-video

video

component

connect M1-D cable IRin

Pr Pr

Pb Pb

serialcontrol

M1-DA vesa trigger1

trigger2

component

s-video

video

component

connect VESA cable

IRin

Pr Pr

Pb Pb

serialcontrol

M1-DA vesa trigger1

trigger2

component

s-video

video

component

onnect power cable

IRin

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1

trigger 2

component

s-video

video

component

Displaying a video image

Remove the lens cap.

Press the Power button on the top of the projector.

The projector chimes if the chime feature is enabled (page 28). The LED

flashes green and the fans start to run. When the lamp comes on, the startup

screen displays and the LED is steady green. It can take a minute for the

image to achieve full brightness.

? No startup screen? Get help on page 12.

Plug in and turn on the video device.

An image from the video device should appear on the projection screen. If it

doesn’t, press the Source button on the keypad.

Adjust the height of the projector by pressing the release button to extend

the elevator foot. Rotate the leveling foot, if necessary.

Position the projector the desired distance from the screen at a 90 degree

angle to the screen. See page 33 for a table listing screen projected image

sizes and distances to the screen.

remove lens cap

press Power

turn on video device

adjust height

rotate

leveling

foot

elevator

foot

adjust distance

Adjust the zoom or focus rings by rotating them until the desired image size

and sharpness are produced.

If the image is not square, adjust the keystone using the buttons on the key-

pad. Press the upper Keystone button to reduce the width of the upper por-

tion of the image, and press the lower Keystone button to reduce the width

of the lower portion.

The Contrast, Brightness, Color, andTint are factory calibrated to D65 col-

ors, but you can adjust these settings in the Picture menu if necessary.

See page 21 for help with the menus.

adjust zoom and focus

focus

zoom

adjust keystone

adjust Picture menu

Andere Handbücher für SP5700

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere InFocus Projektor Handbücher

InFocus

InFocus IN5122 Bedienungsanleitung

InFocus

InFocus NLMP19005 Bedienungsanleitung

InFocus

InFocus LP 120 Leitfaden

InFocus

InFocus LP740B Bedienungsanleitung

InFocus

InFocus LP 650 Bedienungsanleitung

InFocus

InFocus IN5132 Bedienungsanleitung

InFocus

InFocus IN5542 Bedienungsanleitung

InFocus

InFocus IN5552L Bedienungsanleitung

InFocus

InFocus X6 Bedienungsanleitung

InFocus

InFocus LitePro 580 Bedienungsanleitung

InFocus

InFocus IN3114 Bedienungsanleitung

InFocus

InFocus LitePro 210 Bedienungsanleitung

InFocus

InFocus LP260 Bedienungsanleitung

InFocus

InFocus ScreenPlay 4800 Bedienungsanleitung

InFocus

InFocus IN112a Bedienungsanleitung

InFocus

InFocus IN13x Series Bedienungsanleitung

InFocus

InFocus LP130 Bedienungsanleitung

InFocus

InFocus SP777 Gebrauchs- und Pflegehandbuch

InFocus

InFocus ScreenPlay 7210 Bedienungsanleitung

InFocus

InFocus IN1501 Bedienungsanleitung

InFocus

InFocus ScreenPlay 7205 Bedienungsanleitung

InFocus

InFocus LP280 Leitfaden

InFocus

InFocus SP5700 Installationshandbuch

InFocus

InFocus IN134UST Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung