InHand VG710 Bedienungsanleitung
1. Packing List
VG710 Onboard Gateway
Quick Start Guide
Version: V1.0
Date: December 12
4 mounting bolts1 network cable1 power cable1 main unit
Standard packing list:
Optional accessories:
2 LTE antennas
1 OBD-to-20 pin connection cable
(for engineering projects) 1 20-pin extension cable (for custom projects)
2 Wi-Fi antennas (2 types) 1 GNNS antenna 1 Bluetooth antenna
Dongfeng Tianlong
Dongfeng Tianjin
Sinotruck HAOWO
BAIC Motor Foton
BAIC Motor Auman
(BJ4259SNHKB-AA)
Iveco (NJ6725DC)
Iveco (NJ6605DC)
Iveco (NJ1045EFCS)
Iveco (NJ6605DC)
Yutong Heavy Industries
(1) Installing the SIM card and microSD card
Install the SIM card for Internet access through dial-up. The device automatically performs dial-up after power-on.
In common scenarios, install the SIM card, dial-up antenna, GNSS antenna, and Wi-Fi antenna on the device,
connect to the I/O interface, and then connect to the power supply.
Antenna interface
RS232 serial port
Network port
Micro USB
I/O interface
Power interface
Indicator
Reset button
MicroSD and
SIM card slot
2. Adapted Vehicle Models
3. Appearance
4. Installation and Wiring
VG710 Onboard Gateway Quick Start Guide 2 / 6
(2) Installing the antennas
Note:
During installation, ensure that the dial-up antenna, GNSS antenna, Wi-Fi antenna, and Bluetooth antenna
have one-to-one mapping with the antenna interfaces.
When the device performs dial-up, Cellular indicates the primary dial-up antenna, and Diversity indicates the
secondary dial-up antenna. When signals are strong, you only need to install the primary antenna.
When signals are weak, install the primary and secondary antennas.
Installation steps:
1. Make ready the antennas and identify the antenna interfaces.
2. Fasten the antennas in the clockwise direction. Installation of the GNSS antenna is used as an example.
The installation procedures for the other antennas are the same.
DB-9 interface definition
PIN Definition PIN Definition PIN Definition
1
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
2
3
4
5
6
7
8
9
15
69
(3) Pins of the RS232 serial port
Currently, InHand Networks does not define the application scenarios of the RS232 serial port.
You can connect to this port as needed.
Industrial terminals (20 pins)
PIN PIN
1
GND
AI2/DI2
AI4/DI4
AI6/DI6/FWD
GND
DO2
DO4
1-Wire
CANL
485-
11
12
13
14
15
16
17
PIN
18
19
20
2
3
4
5
6
7
8
9
10
Terminal NameTerminal Name
GND
AI1/DI1
AI3/DI3
AI5/DI5/WHEEL TICK
GND
DO1
DO3
GND
CANH
485+
Terminal Name
(4) I/O interface
The I/O interface is connected to the vehicle diagnosis interface to retrieve the vehicle status data.
VG710 Onboard Gateway Quick Start Guide 3 / 6
OBD-II adapter cable
OBD-II
connector
Female J1939
connector
In a normal engineering environment, connect to the power supply V+, GND, and ignition sense cable. Connect the
ignition sense signal cable to the ignition sense cable, as shown in Figure 1. Connect the ignition sense cable and
the anode in parallel in the test state, as shown in Figure 2.
Note: The device cannot be started if the ignition sense cable is not connected.
Power input range: 9-36 V DC;
recommended power: 18 W
Ways to obtain power:
(1) Vehicle battery
(2) Storage battery
(3) Lighter
(4) Power adapter (used indoors)
Power interface
PIN PIN
1 V+
GND
NC
Ignition sense
2
34
Definition Color Color
Black
Red
White
Definition
(5) Connecting to the power supply
VG710 Onboard Gateway Quick Start Guide 4 / 6
图 1 图 2
V+
V+
GND
GND
Ignition sense
Ignition sense
12
34
I/O connector
Receptacle
1 10
11 20
Connect the network cable between the device and terminal.
Currently, InHand Networks does not define the application scenarios of the USB interface.
Step 1: Connect to the device through the network cable or Wi-Fi (see the SSID and key on the nameplate).
If you use Wi-Fi, the Wi-Fi indicator is steady on in green or blinks.
Step 2: Enter the default device IP address 192.168.2.1 in the address bar of the web browser to open the
login page.
Step 3: Enter the default username adm and password 123456 to go to the web interface.
(2) Verifying the dial-up, GNSS, and OBD functions
1
2
3
Network
cable
Wi-Fi
5. Status Confirmation
(6) Connecting the network cable
(7) USB interface
(1) Logging into the device web interface
VG710 Onboard Gateway Quick Start Guide 5 / 6
You can press the Reset button to restore default settings as follows.
Step 1: Power on the device and press the Reset button at the same time. About 15 seconds later, only the System LED
indicator is turned on in red.
Step 2: Release the Reset button when the System LED indicator is turned off and then turned on in red.
Step 3: Press and hold the Reset button for 1 second when the System LED indicator is turned on. Then, release the
Reset button.
After step 3, the System LED indicator blinks for 2 to 3 seconds and then turns off. In this case, the device is successfully
restored to default settings.
Dial-up: After the dial-up function is enabled on the Network > Cellular page, Connected and the allocated IP address
are displayed in the status bar. In this case, the device is successfully connected to the Internet, and the Cellular
indicator is steady on in green, as shown in Figure 1.
GNSS: After the GPS function is enabled on the Services > GPS page, the gateway location is displayed in the status
bar, indicating that the GPS function is normal, as shown in Figure 2.
OBD: The OBD function is normal if Connected is displayed on the Services > OBD page and data is uploaded, as
shown in Figure 3.
Figure 1 Figure 2
Figure 3
6. Default Setting Restoration
VG710 Onboard Gateway Quick Start Guide 6 / 6
Andere Handbücher für VG710
3
Inhaltsverzeichnis
Andere InHand Tor Handbücher
InHand
InHand VG814 Bedienungsanleitung
InHand
InHand InGateway502 Bedienungsanleitung
InHand
InHand InGateway974 Gebrauchsanweisung
InHand
InHand IG502 Bedienungs- und Wartungsanleitung
InHand
InHand IG902-B Bedienungs- und Wartungsanleitung
InHand
InHand InGateway502 Gebrauchsanweisung
InHand
InHand IG601 Bedienungsanleitung
InHand
InHand VG710 Bedienungsanleitung
InHand
InHand VG710 Bedienungsanleitung
InHand
InHand IG601 Bedienungsanleitung
Beliebte Tor Handbücher anderer Marken
LST
LST M500RFE-AS Bedienungsanleitung
Kinnex
Kinnex Media Gateway Bedienungsanleitung
2N Telekomunikace
2N Telekomunikace 2N StarGate Bedienungsanleitung
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung
Telsey
Telsey CPVA 500 - SIP Bedienungsanleitung
