Inhep Digital Security IDS 800 Benutzerhandbuch

2 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45

IDS800INSTALLERMANUAL

Summary of Operation

mrasid/mrA ]#[ +]EDOCRESU[

mrAyawAkciuQ

nwoddloH

]1[

dnoces1rof

mrAyatSkciuQ

nwoddloH

]5[

dnoces1rof

oG&mrAyatSkciuQ

nwoddloH

]6[

dnoces1rof

lenaPybrewsnAdecroF ]8[

demrasidebtsummetsyS-

cinaP

nwoddloH

]P[

dnoces1rof

eriF

nwoddloH

]F[

dnoces1rof

ycnegremElacideM

nwoddloH

]M[

dnoces1rof

yromeMmralA

nwoddloH

]0[

dnoces1rof

eliforPyatSegnahC ]EDOM[ +]9[ +]REBMUNELIFORP[ +[((

(

((]

enozassapyB [((

(

((]+]REBMUNENOZ[

enozemihcmargorP

nwoddloH

]2[

[+dnoces1rof

]

REBMUNENOZ

+[((

(

((]

enozyatsmargorP

nwoddloH

]3[

[+dnoces1rof

]

REBMUNENOZ

+[((

(

((]

enozzzubmargorP

nwoddloH

]4[

[+dnoces1rof

]

REBMUNENOZ

+[((

(

((]

sutatSelbuorTweiV

nwoddloH

]7[

sseruD ]#[ +]EDOCSSERUD[

41egapeeS-ediuGgnimmargorProF

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 3

IDS800INSTALLERMANUAL

Contents

1. Introduction to the IDS800............................................5

1.1 Features...........................................................................5

2. Installation and Wiring ..................................................6

3. End-of-Line Resistors/Tamper per Zone ....................7

4. Connecting the Telephone Communicator ................8

5. Programmable Outputs.................................................8

6. Expansion Board ...........................................................9

7. The Key-Switch or Remote Control Unit ..................10

8. Additional Technical Data ...........................................10

9. Hardware Reset Switch ..............................................12

10. Event Log.....................................................................12

11. Dialler Progress Mode................................................13

12. Download Code ...........................................................13

13. Programming Instructions ..........................................14

13.1 Introduction ....................................................................14

13.2 Location Values..............................................................14

13.3 Programming the Panel .................................................15

13.4 Program Location Summary..........................................16

14. Trouble Conditions Summary.....................................52

4 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45

IDS800INSTALLERMANUAL

Figures

Figure 1: Connection Diagram..............................................6

Figure 2: Tamper per Zone Connection ..............................7

Figure 3: Resistors user for Tamper per Zone ...................8

Figure 4: Programmable Output Configuration ..................9

Figure 5: Expansion Board Connection ..............................9

Figure 6: Strobe Output Sequence ...................................29

Figure 7: Fire Detect Output Sequence............................30

Tables

Table 1: Dialler Progress as shown by zone LED’s..........13

Table 2: Value represented by each zone indicator.........14

Table 3: Binary Representation..........................................15

Table 4: Location/ Zone Defaults........................................17

Table 5: Programmable Zone Types...................................18

Table 6: Output Options ......................................................28

Table 7: Location default values ........................................28

Table 8: Standard Contact ID reporting codes .................35

Table 9: Alarm reporting codes...........................................36

Table 10: Trouble Conditions .............................................52

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 5

IDS800INSTALLERMANUAL

1. Introduction to the IDS800

The IDS800 is a versatile, state of the art, microprocessor based, eight

zone alarm panel. Most features are optional and may be programmed

either directly through the keypad or via the telephone system, using

theIDS download softwareand appropriatemodem.There areeight

programmableburglaryzones, appropriatesiren,auxiliary power

outputs and 5 outputs which may be programmed to perform various

trigger/switchingfunctions.

For correct operation the IDS800 must be used in conjunction with the

specifiedtransformer/batterycombinationand appropriateperipheral

sensorsand signalling devices.

1.1 Features

Four wire keypad operation - up to a maximum of 4 keypads.

Eight,fullyprogrammable, end-of-line(3K3)supervised zones,

and 1 dedicated panic zone per keypad which is not end-of-line

supervised.

Optionaltamperreporting perzoneusing doubleend-of-line

resistors (12K and 4K7).

Fullyprogrammable digital telephonecommunicator which

supports most industry standard formats.

Fiveprogrammabletriggeroutputs.

Non volatile EEPROM memory retains all program and event log

data in the event of a total power failure.

Programmableloop response time forall zones (global).

Upand downloadableusing IDS windowsbasedsoftware.

Excellent protection against lightning (provided by specialised

“zap tracking” and transient suppressors).

Auto-arm - panel can be programmed to arm daily at a pre-

determinedtime.

Event log (200 events) date and time stamped.

Fax defeat allows download access to the panel with other

devices connected to the phone line.

Dualreportingprovides for duplicatedreportingto twoindependent

central base stations.

Programmablesilent or audiblepanic.

Uniquediallerprogress barallowingfor monitoringofdialler

status.

6 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45

IDS800INSTALLERMANUAL

2. Installation and Wiring

Pleaserefer toFigure 1:Connection Diagramand familiariseyourself

with the following sections.

Figure 1: Connection Diagram - without tamper per zone

ZONE 8

ZONE 7

ZONE 6

ZONE 5

ZONE 4

ZONE 3

ZONE 2

ZONE 1

+TX

18V AC

AUXILLIARY

OUTPUTS

KEYPAD

12V

SIREN

CONNECT TO MAINS

TRANSFORMER

RADIO TRANSMITTER /

COMMUNICATOR POWER

PANIC

BUTTON

N/O

PANIC

BUTTON

N/O

NC C

C+

P.I.R.

MAG SW N/C

CONNECT AS

REQUIRED WITH A

RESISTOR IN

UNUSED ZONES

12V BATTERY

123

456

789

ZONE 1

ZONE 2

ZONE 3

ZONE 4

ZONE 5

ZONE 6

ZONE 7

ZONE 8

DAT

GND

+12V PAN

LED

3K3

NOTE: NO END OF

LINE RESISTOR

DOOR LED

EARTH

LINE

PHONE

SW1

HARDWARE

RESET

SWITCH

FU2 AUXILIARY

POWER FUSE

1 AMP

FU1 BATTERY

FUSE

4 AMP

Dialler Board

Position of

Dialler Board

RADIO

TRANSMITTER

COMMUNICATOR

TELKOM

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 7

IDS800INSTALLERMANUAL

3. End-of-Line Resistors/Tamper per Zone

All zones are end-of-line supervised.Any unused zones must also

be terminated with the appropriate resistor.

The end of line resistor should be placed inside or as close to the

sensor as possible.

If the zones are not programmed to report tamper by zone i.e. a

[0] is programmed into location 11 then use the 3K3 end-of-line

resistor.

If the zones are programmed to report tamper by zone, the 4K7

and 12K end-of-line resistors should be connected as per Figure 2

below. The 4K7 and 12K resistors are not included with the panel

but may be obtained from your local distributor of IDS products.

Figure 2: Tamper per Zone Connection

The operation of the tamper is as follows:

If the panel is not armed and a tamper condition occurs, the

siren will not sound but a tamper condition will be reported.

If the panel is armed and tamper condition occurs the alarm

will register a zone violation and a tamper condition will be

reported.

Regardless of whether the panel is armed or not, if a zone is

programmed as a priority/panic zone, a tamper will register a

panic condition as well a tamper condition.

If the tamper per zone is enabled, it affects all zones and therefore

both end-of-line resistors must be connected in all zones. If the

tamper facility is not used on a zone then the 12K resistor must

be connected directly across the zone (i.e. between the zone

8 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45

IDS800INSTALLERMANUAL

input and ground) and the 4K7 resistor is used as the normal end-

of-lineresistor.

The colour codes for the 12K and 4K7 resistors are as seen in

Figure3below.

Figure 3: Resistors used for Tamper per Zone

Purple

Brown Orange

Red

2K 4K7

Yellow Red

4. Connecting the Telephone Communicator

Referto Figure1.

The integral communicator has built in lightning protection to

protect it from lightning induced transients. For optimum

protection connect a low impedance earth to the communicator.A

poor earth will be ineffective and may result in damage to the

communicatorand alarmpanel.

Always connect the telephone communicator in the line seizure

mode. Never in parallel with the telephone i.e. connect the

telephonereceiverto thecommunicator terminalsmarked“phone”

and the incoming line to the terminals marked “line”.

5. Programmable Outputs

A relay board must be used when any device requiring a high current is

connected to a programmable output. The current sink and source

capability is the same for outputs 1, 2 and 3. The output circuitry

consists of a 12 volt source with a 56Ωseries resistor. Current sink is

via a 1000Ωresistor to negative. The output circuitry is provided in

Figure4overleaf.

There is also an expansion board attached to the keypad bus which

providesfor an additionaltwo programmableoutputs whichfunctionas

per outputs 1 - 3. See the connection diagram in Section 2 for further

details. See also Section 6: Expansion Board.

IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45 9

IDS800INSTALLERMANUAL

Figure 4: Programmable Output Configuration

6. Expansion Board

Attached to the keypad bus, in parallel with the keypad, is an optional

expansionboard whichallowsfor thefollowing:

Programmable outputs 4 and 5 which function as per the values

programmed into locations 22 - 40 and locations 159 - 166.

Designated keypad buzzer which will function as per the

description in the user manual.

ARM, READY and POWER LED’s which will function as per the

description in the user manual for keypad LEDs.

Figure 5: Expansion Board Connection

Keypad

123

456

789

ZONE 1

ZONE 2

ZONE 3

ZONE 4

ZONE 5

ZONE 6

ZONE 7

ZONE 8

GND

DAT

+12V

Keypad connection

on main board

Keypad Buzzer

Power LED

Ready LED

Arm LED

Auxilliary

Outputs

Expansion

Board

12V

56R

1000R

GND Output 2

56R

1000R

GND Output 1

56R

1000R

GND Output

10 IDS800 INSTALLER MANUAL NO. 700-175-02N ISSUED JUL 2003 VER 1.45

IDS800INSTALLERMANUAL

7. The Key-Switch or Remote Control Unit

A momentary key-switch or non-latching remote control receiver may

be connected to any zone to allow remote arm/disarm capability and/

or remote panic.

If a key-switch or remote control unit is used, a 3K3 resistor must

be connected between the zone input and ground. (Use the 4K7

and 12K resistors if tamper per zone is enabled).

Use a normally open, spring-loaded momentary key-switch or a

non-latchingremote controlunit.The remotereceivermust provide

a pulsed output.

If using a key-switch, program the zone as anArm/Disarm zone

i.e. a value of [5] entered into the relevant location.

If using a remote control, program the zone as either a Paniczone

or anArm/Disarm zone, as required.

The panel will arm instantly (no entry/exit delay) when arming by

means of a key-switch or remote control unit.

The panel has an exit delay which can be enabled or disabled

with the key-switch or remote control (See location 12).

8. Additional Technical Data

Use a suitable transformer with an output voltage of 15 volts AC

±10% with a 16VAminimum rating. A32 VAtransformer is

preferableforlarger installations.

Use a 12v sealed lead acid battery, min. 3ah. The back up period

after mains failure will depend on the number of keypads, sensors

and peripheral devices attached to the system. The current drawn

by the panel and keypad (no indicators illuminated) excluding

sensors is 240mA.

Thepanic zone providedon the keypadis not anend-of-line

Inhaltsverzeichnis

Andere Inhep Digital Security Sicherheitssystem Handbücher

Inhep Digital Security

Inhep Digital Security IDS 1600 Benutzerhandbuch

Inhep Digital Security

Inhep Digital Security IDS 1200 Benutzerhandbuch

Inhep Digital Security

Inhep Digital Security IDS404 Benutzerhandbuch

Inhep Digital Security

Inhep Digital Security IDS X Series Bedienungsanleitung

Inhep Digital Security

Inhep Digital Security IDS816 Montageanleitung

Inhep Digital Security

Inhep Digital Security IDS 400 Benutzerhandbuch

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung