INIM Electronics Aria Montageanleitung

Installation and programming manual

Aria

Wireless keypad

Installation and programming manual

EN 50131-1

EN 50131-5-3

EN 50131-3

EN 50130-4

EN 50130-5

Aria Wireless keypad

Table of

contents

Chapter 1 General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1-1 About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

1-2 Manufacturer's details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

1-3 Air2 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Chapter 2 Keypad description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3-1 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

3-2 Wall-mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

3-3 Enrolling keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Chapter 4 Use of device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4-1 Operating statuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

4-2 Backlighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

4-3 “Rolling-code” authentication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

4-4 Info/setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Appendix A Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

The information contained in this document is the sole property of INIM

Electronics s.r.l. No part may be copied without written authorization

from INIM Electronics s.r.l.

General information 3

Installation and programming manual

Chapter 1

GENERAL INFORMATION

1-1

About this manual

MANUAL CODE

DCMIINE0A2ARIAV8

REVISION

1.00

1-2Manufacturer's details

Manufacturer: INIM Electronics s.r.l.

Production plant: Via Fosso Antico - Centobuchi

63076, Monteprandone (AP) - Italy

Tel.: +39 0735 705007

Fax: +39 0735 704912

e-mail: [email protected]

Web: www.inim.biz

The persons authorized by the manufacturer to repair or replace the parts of this

system, hold authorization to work on INIM Electronics brand devices only.

1-3Air2 System Description

The advanced Air2 two-way wireless intrusion protection system (868MHz

frequency) integrates directly with all models in INIM intrusion control panel

range.

For secure deployment and operations of the Air2 wireless intrusion protection

system, it is necessary to refer to the Installation and programming guide of the

hardwired intrusion control panel in use.

Note

The notified body N°0051, were involved in the R&TTE Directive conformity

assessment procedure for all the devices of the Air2 system.

Table 1: Technical specifications of Air2 system

Operating frequency range

868.0 - 868.6MHz

selectable channels

868.1, 868.3, 868.5MHz

Communication type

Two-way

Modulation

GFSK

Device supervision

From 12 to 250 minutes

Security grade

Environmental class

4Keypad description

Aria Wireless keypad

Chapter 2

KEYPAD DESCRIPTION

The Aria wireless keypad provides all the necessary functions for control and

management of a SmartLiving installation equipped with an Air2 system, which it

can interface with through the Air2-BS200 transceiver. It integrates all the

functions of a hard-wired keypad and provides a graphic icon display.

It is equipped with an accelerometer which provides both anti-tamper and

“wakeup” from stand-by functions, whereas the brightness sensor controls the

display and key brightness optimally with respect to the surrounding environment.

Moreover, it has an automatic shutdown function in the event of loss of wireless

connection.

Aria is also equipped with a connector which allows hardwiring connection if

required.

FUNCTIONS

• Communicates with Air2-BS200 transceiver @ 868MHz

• Backlit graphic display

• Icon Easy4U interface

• Programmable backlight

• Brightness sensor

• 4 indicator LEDs

•Signalbuzzer

• Inertial tamper protection

• Accelerometer controlled “Wakeup” function

• Mounts to “503” outlets

• Attaches to wall bracket or counter support

• 6 -20V ancillary power connector

• “Rolling-code” authentication

Table 2: Technical specifications

Batteries

CR17450 Lithium battery - 3V -

2200mAH, 2

Battery life

2 years

“Low battery” fault voltage

Less than 2.4V

Ancillary power supply

6 - 20 V

Stand-by current draw

90μA

Maximum current draw

25mA

Operating temperature and humidity

-10°C +40°C, 93%

Dimensions (W x H x D)

140 x 115 x 27mm

Weight

255g

Security grade

Environmental class

Number of Aria keypads supported by

Air2-BS200

Maximum 4

Keypad description 5

Installation and programming manual

Table 3: Description of parts

Display

Brightness sensor

LED

Ancillary power

connector

Battery switch

Battery

compartment

cover

Cover screws

Counter support

Wall bracket

support

Screw location

Backlocking grips

Mounting screw

location

Cable entry

Aria - front

Wall bracket

Aria - back

6Installation

Aria Wireless keypad

Chapter 3

INSTALLATION

The Aria keypad can be mounted in two ways each of which requires a different

installation procedure:

• Counter mount, with no fixed installation point.

When using this method, it is necessary to disable the keypad tamper-signal option

on the control panel.

You can stand the keypad on flat surfaces by means of the support on the back of

the device (table 3, H).

• Wall mount by means of the wall bracket (see paragraph 3-2 Wall-mounting).

For this mode it is advisable to enable the keypad tamper-signalling option on the

control panel.

For instructions regarding keypad tamper signalling refer to the programming

manual of the SmartLiving control panel.

3-1Power supply

Power to the keypad can be supplied in two different ways:

• By means of the connector on the back of the device (table 3, D) which allows 6-20

• By means of two CR1745 Lithium batteries installed in the battery compartment

(table 3, F).

The battery power supply can be turned On or Off by means of the switch on the

back of the device (table 3, E).

The manufacturer cannot guarantee the declared battery life.

ATTENTION!

Do not use batteries other than those indicated by the manufacturer as they may

explode.

Used batteries must be disposed in accordance with local regulations.

3-2Wall-mounting

1. Choose a suitable mounting placement.

2. Put the wall bracket on the selected placement and mark the screw holes (table

3, L

)

3. Drill the holes.

4. If you intend wiring the device, pull the wires through the cable entry (table

3, F

) and wire up the keypad.

If you intend using the batteries, place them in the battery compartment

and put the switch in the “ON” position (refer to paragraph 3-1 Power sup-

ply

5. Using the anchor screws, secure the bracket to the wall.

6. Enroll the device.

7. Mount the keypad to the wall bracket, by first inserting the locking grips

(table 3, K

) in place, then by pushing the keypad toward the wall then down-

ward.

8. Fasten the securing screw in place (table 3, J

)

BATT OFF

BATT ON

Installation 7

Installation and programming manual

3-3Enrolling keypads

The SmartLiving control panel can manage up to 4 Aria keypads for each Air2-

BS200 installed. However, each control panel model supports a maximum number

of keypads which must be respected.

During the addressing phase use free addresses only and ensure that no other

keypads (Joy, Concept, NCode or Alien) are present at the address of the Aria

keypads.

Via Keypad:

1. Access the Installer menu, select “Keypads” then “ChoosePeripheral”.

2. From the list that appears select the keypad to be assigned to the wireless

function.

3. Select the “Wireless” option.

4. From the list select the wireless reader simulated by the Air2-BS200 trans-

ceiver the Aria keypad is to be associated with.

5. Access the “Enroll device” section, then select “Wireless Keypad”.

Via SmartLeague:

1. Select a keypad from the those configured in the System Tree Menu.

2. Access the keypad “Programming” section and click on the “Wireless Key-

pad” check box.

3. Click on the “Enroll” button. The enrollment process window will open.

4. From the list select the wireless reader simulated by the Air2-BS200 trans-

ceiver the Aria keypad is to be associated with.

5. Click on the “Enroll” button.

6. Click simultaneously on buttons “1” AND “3” on the Aria keypad.

This operation sends the enrollment request.

If the keypad menu appears, select “Enroll” option (paragraph 4-4 Info/

setup menu).

7. Once the device is enrolled, the Aria keypad will confirm the successful out-

come of the operation.

Via Keypad:

the keypad that generated the enrollment process will emit a confirmation

beep.

Via SmartLeague:

The software window will show a a confirmation message.

8Use of device

Aria Wireless keypad

Chapter 4

USE OF DEVICE

4-1

Operating statuses

The Aria keypad has 3 operating statuses

•Active

•Stand-by

• No communication

ACTIVE

During this status the keypad will be at maximum power consumption level due to

the active status of:

•Display

• Backlighting

• Signal LEDs

By means of the interface with the control panel it is possible to access the User

and installer menus and carry out the same operations that can be accessed from

other keypads on the SmartLiving system.

The keypad is not equipped with a proximity reader, voice functions, thermostat

and thermal probe.

The “active” status will hold for as long as there is activity on the keypad (keys are

being pressed or the buzzer is active). If there is no activity for 10 consecutive

seconds the status will pass from “active” to “stand-by”.

STAND-BY

During this status the keypad display will be off, the signalling LEDs will be Off or

blinking, and the wireless transmission (broadcast) will be active.

The Stand-by status will hold until a key is pressed, or a remote activation occurs

(for example, the buzzer signals an Exit Time) or the keypad is moved.

COMMUNICATION

During this status the display, backlight and LEDs will be off.

The keypad will enter this status when the wireless communication with the

control panel is interrupted in a continuous way. When the keypad enters this

status the “NO COMUNICATION” message will appear on the display.

The keypad will try to communicate with the control panel at one-minute intervals

in an attempt to re-establish communication.

4-2Backlighting

The backlight can be programmed from the keypad in accordance with the

measured ambient-brightness. The keypad manages two different brightness

settings:

•Day

•Night

These settings can be programmed via the “Keypad” option from the “Options”

section in the User menu.

Please note that the backlight is the most important factor with regard the

consumption of battery power.

Use of device 9

Installation and programming manual

4-3“Rolling-code”

authentication

A further guarantee of security for Aria keypad wireless transmissions are the

over-the-air random codes. These random codes allow the Air2-BS200 to

authenticate the validity of each wireless keypad transmission.

In the event of irregular wireless activity, the requested operation will not be

completed.

To reset wireless transmissions and rolling code authentication, press and hold

keys “1” and “3” simultaneously.

4-4Info/setup menu

Aria has menu of its own for the access to some information on the keypad and on

the wireless system, and for some programming functions.

The menu, in full version, has 7 options. It can be are activated by holding the

keys “1” and “3” simultaneously when the keypad has been enrolled and the

SmartLiving control panel is in maintenance status.

In the case of Aria factory data restoration, the menu is automatically activated,

but in a shortened version, showing the first three options only.

The sections of the menu are:

•

Enroll

- starts enrollment process

•

Keypad Info

- information regarding the keypad and installation of the Air2.

1st line:

- WK: operating frequency

- Ver: firmware version of the Aria keypad

2nd line:

- SN: serial number of the Aria keypad

3rd line:

- N: number of the Aria keypad managed by the Air2-BS200

- WK: address of the Aria keypad in the control panel

- Ch: RF transmission channel, primary [X] and secondary [Y] (refer to “secondary

channel”)

4th line:

- BS: address in the control panel of the associated Air2-BS200 transceiver

- SN: serial number of the associated Air2-BS200 transceiver

•

Power Info

- battery charge percentage or presence of the ancillary voltage

•

Second W Channel

- selects the RF support channel which guarantees the

operating capacity of the keypad.

This channel must always be different from the primary channel used by the Air2-

BS200 transceiver.

•

Factory data

- starts a restore of the factory default settings after a confirmation

request.

This procedure deletes also the keypad address on the control panel. After this the

info/setup menu will be shown in a shortened version, with the first three options

only.

•

Test RF

- carries out an analysis of the primary wireless channel and shows the

average RSSI value of the signal and a value from 0-100 which indicates the

channel quality (the RF Test function is enabled only when the control panel is in

maintenance mode).

•

Update Firmware

- starts the upgrade of the wireless firmware.

WK868 Ver:1.000

SN:SNSNS1

N-WK:AA Ch:X-Y

BS:BB SN:SNSNS2

10 Order codes

Aria Wireless keypad

Appendix A

ORDER CODES

Please quote the following order codes when ordering items from the INIM

Electronics product range:

Code Product description

Air2-Aria

Wireless keypad with backlit graphic display

Air2-BS200/10

Wireless transceiver module, 10 terminals

Air2-BS200/30

Wireless transceiver module, 30 terminals

Air2-BS200/50

Wireless transceiver module, 50 terminals

Air2-DT200TB

Wireless dual-technology curtain detector, in white

Air2-DT200TM

Wireless dual-technology curtain detector, in brown

Air2-FD100

Wireless smoke detector

Air2-Hedera-F

Wireless outdoor sounder with anti-foam protection

Air2-Hedera-F#

Wireless outdoor sounder with anti-foam protection, batteries not included

Air2-Hedera-FM

Wireless outdoor sounder with anti-foam protection, in metal effect enclosure

Air2-Hedera-FM#

Wireless outdoor sounder with anti-foam protection, in metal effect enclosure, batteries not

included

Air2-IR100

Two-way wireless PIR with 12m coverage

Air2-IR100/C

Two-way wireless PIR with 20m coverage

Air2-KF100

4 button remote-control keyfob

Air2-MC100B

Wireless magnetic contact with 2 inputs/outputs, in white

Air2-MC100M

Wireless magnetic contact with 2 inputs/outputs, in brown

Air2-MC200B

Two-way wireless magnetic contact, in white

Air2-MC200M

Two-way wireless magnetic contact, in brown

Air2-ODI100W

Wireless outdoor double infrared detector

Air2-OTT100W

Wireless outdoor triple-technology detector

Air2-UT100

Universal wireless transceiver

Air2-XDT200W

Wireless dual-technology detector - 8m

Air2-XIR200W

Wireless dual-technology PIR detector - 12m

DCMIINE0A2BS200E

Air2 devices installation manual

SmartLiving10100L

Intrusion control panel: manages 10 to 100 terminals, 15 partitions, switching power supply

@5A, optional TCP/IP connectivity, comes in metal enclosure with housing for 1 battery @17Ah

SmartLiving10100L/

Intrusion control panel: manages 10 to 100 terminals, 15 partitions, switching power supply

@5A, optional TCP/IP connectivity, comes in metal enclosure with housing for 1 battery @17Ah.

EN50131-6 grade 3 certified.

SmartLiving1050

Intrusion control panel: manages 10 to 50 terminals, 10 partitions, switching power supply @3A,

comes in metal enclosure with housing for 1 battery @ 7 or 9Ah

SmartLiving1050/G3

Intrusion control panel: manages 10 to 50 terminals, 10 partitions, switching power supply @3A,

comes in metal enclosure with housing for 1 battery @ 7 or 9Ah. EN50131-6 grade 3 certified.

SmartLiving1050L

Intrusion control panel: manages 10 to 50 terminals, 10 partitions, switching power supply @3A,

comes in metal enclosure with housing for 1 battery @17Ah

SmartLiving1050L/

Intrusion control panel: manages 10 to 50 terminals, 10 partitions, switching power supply @3A,

optional TCP/IP connectivity, comes in metal enclosure with housing for 1 battery @17Ah.

EN50131-6 grade 3 certified.

SmartLiving505

Intrusion control panel: manages 5 terminals, 5 partitions, switching power supply @ 1.2A,

comes in metal enclosure with housing for 1 battery @7 or 9Ah

SmartLiving515

Intrusion control panel: manages 5 to 10 terminals, 5 partitions, switching power supply @ 1.2A,

comes in metal enclosure with housing for 1 battery @7 or 9Ah

DCMIINE0A2ARIAV8-R100-20160428

Inhaltsverzeichnis

Beliebte Tastenfeld Handbücher anderer Marken

BFT

BFT SELETTO Bedienungsanleitung

Micro Id

Micro Id MP7G3BL Gebrauchsanweisung

WindowMaster

WindowMaster WLI 130 Bedienungsanleitung

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung