Inncom E528 Bedienungsanleitung

Global Leader in Integrated Room Automation Systems

e528 Smart Digital Thermostat

Product Guide

Overview

INNCOM's e4 Smart Digital Thermostat is a po erful, multi-purpose Direct Digital Control (DDC) device that

can control virtually any HVAC system found in hotel guestrooms.

The three e4 models meet different application requirements. The e528 and e527 are

ired and are typically used for ne installation. The e529 is battery-po ered and is

designed to meet the needs of existing properties here re iring is not practicable.

This document describes Model e528; information on the e529 and e527 can be found

in their respective product guides.

Application

In its most basic form, the e528 functions as a programmable DDC thermostat,

automatically adjusting fan speeds and valves to achieve set temperature (Note:

Guests can manually select heat or cool by pressing the OFF/AUTO button and

cycling through OFF, AUTO, HEAT and COOL). The e528 is also an “intelligent”

device capable of linking ancillary sensors and serving as an information gate ay.

For example, coupled ith a magnetic door s itch ( ired or ireless), motion detectors, and other devices, the

e528 becomes the brain of a highly effective Energy Management System (EMS) application, communicating EMS

information requirements to central servers. It comes standard ith five relays and can be equipped ith an on-

board Infrared (IR) or radio frequency (RF) transceiver and Passive Infrared (PIR) motion detector.

The e528 interfaces ith all common HVAC unit voltage configurations (24 volt to 277 volt). The e528 can be

installed in a ired or ireless INNCOM guestroom control system, hich makes installation feasible and

affordable in either ne construction or retrofit installations.

Through interfaces ith other devices and sensors, the e528 supports the follo ing functions:

•Remote HVAC control

•Guestroom HVAC diagnostics

•Remote room occupancy indication

•Automatic lighting control

•Remote mini-bar access reporting

•Remote smoke detector annunciation

•Central Electronic Lock control

•Humidity control

•Remote drape control

•Outside temperature display

•Peak demand load shedding

•Property/Building Management System (PMS/BMS) interface

Figure 1 e528 Digital T ermostat

E 5 2 8 P r o d u c t G u i d e P a g e 2 o f 1 8

A centrally controlled EMS package is created hen the e528 is connected to the property's Central Interface

Net ork (CINET) ith a pair of lo voltage ires or by the property’s high-speed TCP/IP net ork ith the

addition of a TCT (an Ethernet gate ay device). RF net orking is possible ith radio equipped models.

The e528 features a guest-friendly graphic interface ith intuitive controls (Figure 2). A user guide for the e528,

ritten primarily for installers and facility management personnel, is available (see References belo ).

Wireless Communication

2.4Ghz wireless RF

Table 1 e528 RF C aracteristics

Performance 0dB 20dB

RF Data Rate 250kbps 250kbps

Antenna Type SMT SMT

Indoor Range 70ft 100ft

Outdoor/ RF line-of-sig t range 540ft 1000ft+

Transmit Power 1mW 10mW

Receive Sensitivity -94.6dBm -94.6dBm

Frequency Band 2.4Ghz 2.4Ghz

Encryption AES-128 AES-128

Protocol 802.15.4 802.15.4

Frequency C annels 11-26 11-26

Ranges are determined by performing an RF link quality test using t o identical e528 thermostats containing

radios as defined in tables 2 and 3. The maximum distance threshold is based on a 95% overall link quality.

Outdoor ranges ere conducted in a lo noise, free air environment. Indoor ranges are for reference. Indoor

ranges are impacted by the ambient environmental noise floor, and building construction materials.

Figure

e528 Grap ic Inter

face

E 5 2 8 P r o d u c t G u i d e P a g e 3 o f 1 8

IR5 (In rared)

Table 2 e528 IR5 C aracteristics

Performance IR5

Indoor Range Up to 80ft

IR Data Rate 2500 bps

The IR Eye5 orks ithin INNCOM's System-5 protocol and can be used in a fluorescent light environment.

Ho ever, it may be subject to interference from plasma televisions, and care must be taken in situating the device

if a plasma television is present.

Installation Requirements

Location: The e528 must be located on a partitioning interior all, approximately 1.5 m (5 ft) above the floor, in a

site of average temperature. It is important to ensure that the thermostat is located a ay from direct sunlight or

radiant heat, air discharge grills, stair ells, outside doors, steam or ater pipes, arm air stacks,

unheated/uncooled areas, or sources of electrical or radio interference. The unit should not be placed on an outside

all or behind a door. It is essential that the e4 is mounted flush to the all and mounted level in both the horizontal

and vertical planes; incorrect mounting can degrade IR, PIR, and temperature measurement performance.

Installation Requirements or e4 equipped with PIR Motion Detection

The e4 thermostat can be equipped ith a PIR detector to augment the energy management scheme by detecting

motion in the guestroom. Consider the PIR’s vie angle, range characteristics, and mounting position to ensure

proper coverage. Figure 3 belo sho s the ranges of the flat and standard PIRs.

Flat PIR Detection Range (Single Pyro) Standard PIR Detection Range (Dual Pyro)

Figure 3 PIR Detection Ranges

E 5 2 8 P r o d u c t G u i d e P a g e 4 o f 1 8

Mounting: The e528 is usually mounted on a standard double-gang (4 x 4) junction box. If mounted on a single-

gang box, the left side (display side) of the e528 overlaps the all area to the left of the junction box. A lo -

voltage mounting plate, mud ring, or lo -voltage caddy may be used for mounting 24 volt applications.

To mount the e528:

1) Remove the t o small scre s at the base of the e528.

2) Pull the bottom of the back-mounting plate slightly a ay from the front housing and then pull the back-

mounting plate do n.

3) Position the back plate insulator ithin the mounting plate as sho n in Figure 4.

4) Attach the mounting plate to the junction box, using the mounting scre s provided ith the e528. Ensure

that the plate is mounted ith the raised arro pointing UP.

To simplify installing and removing the e528, the headers and sockets described belo and sho n in Figure 5 are

located on the back of the e528. These accept pre-made iring harnesses provided by INNCOM. (Note: Take care

to note hich e528 model is being used. Each model has slightly changed headers and connectors as identified in

the dra ings belo .)

Figure

Mounting Assembly

E 5 2 8 P r o d u c t G u i d e P a g e 5 o f 1 8

Figure

Back View S owing Headers and Sockets

E 5 2 8 P r o d u c t G u i d e P a g e 6 o f 1 8

Headers

The headers for the e528.2G, 3G and 4G

thermostats are substantially the same, though the layouts and labeling on

the PCB are slightly different (see Figure 5 above). The statements and tables belo detail only the headers that differ

in function.

Low Voltage comm / device connector: This header accepts the provided 6-pin harness used to connect lo

voltage communication, door/ indo position s itch, and other room devices to the e528. Table 3 sho s the

pinout for the 2G lo voltage comm / device connector and lists typical functions for each pin. Table 3a sho s

pinout and function for the 3G and 4G. For specifics, refer to the as-built iring diagrams.

Table 3. e528 2G Low Voltage Harness (P/N 62-1462) Pinout

Wire Color Female

Connector

Male

Connector

Function Comment

Bro n 1 1 Common GND

Red 2 2 12VDC Out/In 12VDC Supply

Orange 3 3 S5 Bus Data Tx/Rx or IN 2 Communication Bus

Yello 4 4 IN 1 Door, Windo , PIR, Other

Green 5 5 CINET B RS485 T isted Pair

Blue 6 6 CINET A RS485 T isted Pair

Table 3a. e528 3G/4G Low Voltage Harness (P/N 62-1467) Pinout

Wire Color Female

Connector

Male

Connector

Function Comment

Bro n 1 1 Common GND

Red 2 2 12VDC Out/In 12VDC Supply

Orange 3 3 S5 Bus Data Communication Bus

Yello 4 4 Digital Input Door, Windo , PIR, Other

Green 5 5 No Connection

Blue 6 6 No Connection

External temperature control sensor: This header accepts the iring harness from an external temperature probe

that can be used to supply the e528 ith remote temperature measurements. The e528 uses a 10K 1% thermistor

for external temperature measurement. This external temperature sensor can be used to monitor room

temperature at a different location from here the e528 is mounted or to monitor pipe ater temperature.

RS485 Networks: (refer to Figure 5)

E528.2G can be connected to the RS485 FLN5 net ork by installing the 02-9496 module, then connecting the

RS485 net ork to pins 5 and 6 of the lo voltage comm /device connector as described in Table 3 above.

E528.3G cannot act as the media gate ay for in-room traffic to ards the RS485 net ork. The most common

ay to connect the e528.3G is to connect a PC-485.S5 (P/N: 01-9905) on the S5bus.

E528.4G

E528.4G to 2G RS485 Networked Application: wit or wit out door switc input (See Figure 6 belo )

•Using the adapter (P/N 203-251), connect the harness from the all box (P/N 62-1462) previously

connected to the thermostat being replaced to H1 of the adapter.

•Connect the harness H3 (rainbo ) of 203-251 to the lo voltage comm/device connection of the e528.4G

“2G,” “3G,” and “4G” are internal INNCOM product designations used for convenience to differentiate

individual hard are configurations. No difference in device capability or effectiveness is implied. Due to end-of-

life for certain 2G and 3G components, the e528.4G is no the standard INNCOM install, but 2G and 3G

installations are still supported.

E 5 2 8 P r o d u c t G u i d e P a g e 7 o f 1 8

•Connect the harness H2 (black) of 203-251 to the RS485 header of the e528.4G

NOTE: Take care to not reverse the connections to the e528.4G!

E528.4G New Installation

Stand alone application wit /wit out door switc input

•Using the harness (P/N 62-1467), make the appropriate ire connections, then plug the harness into the

lo voltage comm/device connection of the e528.4G

RS485 Networked Application wit /wit out door switc input (See Figure 7)

•Using the harness (P/N 62-1467), make the appropriate ire connections, then plug the harness into the

lo voltage comm/device connection of the e528.4G.

•Using the adapter (P/N 203-250) and P/N 62-1532-B.12 cables, connect the RS485 A pair to the t o pin

RS485 In header and the RS485 B pair going to the next thermostat to RS485 Out header on the 203-250.

•Connect the harness of 203-250 to the RS485 net ork header of the e528.4G.

Figure

E528.4G New RS485 Networked Application

Figure

4G to 2G RS485 Networked Application

E 5 2 8 P r o d u c t G u i d e P a g e 8 o f 1 8

E528.4G Retrofit Installation

The e528.4G can be used to retrofit an application here a legacy e528 as used. Follo the procedure belo :

4G to 2G Standalone application: wit /wit out door switc input (no back aul network)

•Using the adapter (P/N 203-013) connect the harness from the all box (P/N 62-1462) previously

connected to the thermostat being replaced to H1 of the adapter (see Figure 8).

•Connect the harness of 203-013 to the lo voltage comm/device connection of the e528.4G.

Molex 10-position female socket: This female socket accepts the provided 10-pin Molex connector pre- ired

ith 8-inch, color-coded iring leads. These leads should be connected to the 24VAC or 100–277VAC po er,

valve/fan control iring from the FCU, or other HVAC device ith ire nuts inside in the all junction box in

accordance ith the iring diagram provided by INNCOM.

Note: For installations in w ic all leads are not required, t e extraneous leads s ould be cut off at t e Molex connector.

Figure 8 sho s the pinout for the 10-position Molex male connector supplied ith all relay output models of the

thermostat. The end vie of the male connector from the ire insertion side ith the pin numbers is indicated.

This is the same as looking at the female connector point on the back of the e528.

Typical functions for each ire are listed in Tables 4 and 5. For specifics, refer to the as-built iring diagrams.

Table 4. 24VAC Harness Color Code, Pinout, and Typical Functions

Figure 8 e528.4G to 2G Standalone application

Figure

Pin Molex Connector (Part No. 62.1455 or 62.1464.R)

E 5 2 8 P r o d u c t G u i d e P a g e 9 o f 1 8

24VAC harness (INNCOM Part # 62-1464 R)

Pin Color Typical Function

1 Green Ground

2 Red 24VAC

3 Black Common

4 Blue High Fan

5 Bro n Medium Fan or Second Stage Heat

6 Yello Cold Water Valve (FCU) or Compressor Signal

(Heat Pump)

7 White Hot Water Valve (FCU) or Reversing Valve

(Heat Pump)

8 Grey Valve Po er

9 Violet Fan Po er

10 Orange Lo Fan

Table 5. 100-277VAC Harness Color Code, Pinout, and Typical Functions

100-277VAC harness (INNCOM Part # 62-1455)

Pin Color Typical Function

1 Green Ground

2 Black Line

3 White Neutral

4 Yello High Fan

5 Orange Medium Fan or Second Stage Heat

6 Red Cold Water Valve (FCU) or Compressor Signal (Heat

Pump)

7 Bro n Hot Water Valve (FCU) or Reversing Valve (Heat

Pump)

8 Grey Valve Po er

9 Violet Fan Po er

10 Blue Lo Fan

Wiring: The steps belo provide an overvie of the iring process. Refer to the as-built iring diagrams

provided for exact details.

1. If applicable, use ire nuts to connect the 6-pin lo -voltage harness ires to the applicable lo -voltage

communication (if e528 is part of a ired RS485 centrally controlled system), door/ indo s itch, or

external PIR iring ithin the electrical box (Figure 8). Plug the 6-pin lo voltage harness onto the e528 lo

voltage comm. / device connection header.

2. Use ire nuts to connect the 10-pin Molex iring harness to the po er and valve/fan control signal ires

ithin the electrical box.

3. Plug the pre- ired 10-pin connector into the female receptacle at the back of the e528.

4. Hook the tabs at the top rear of the e528 housing into the matching depressions at the top of the mounting

plate and rotate the bottom of the housing to ard the all until it snaps into place on the mounting plate.

5. Secure the housing to the mounting plate ith the t o small scre s removed in Step 1 of the Mounting section.

6. Apply po er to the e528 by closing the applicable supply breaker. Verify that the e528 po ers up. Several

values should begin appearing on the LCD display.

7. Once installed and connected to po er, the e528 Digital Thermostat typically requires some configuration,

specifically:

•If installing the e528 as part of a net orked, centrally controlled EMS, a unique net ork address must be

assigned to the e528. This is done by entering Service Parameter mode on the e528 and changing the

E 5 2 8 P r o d u c t G u i d e P a g e 1 0 o f 1 8

values of Parameters 10, 11, and 12, hich hold the 5-digit net ork address of the e528. This 5-digit

number is typically the room number in most applications. A “Room List” document is typically

available that lists all rooms and the associated values to set into Parameters 10, 11, and 12. Refer to

Reference A, Section 5.1, for complete instructions for setting the e528 net ork address.

•If the particular HVAC equipment installed as not kno n hen the e528 as shipped, the fan and

heat/cool control outputs of the e528 must be configured to correctly operate the installed HVAC

equipment. Setting the appropriate HVAC control parameters of the e528 to the required values and

resetting the device reconfigures the e528 to properly control most HVAC units. Refer to Reference A,

Section 5.2, for instructions on changing the e528 HVAC related parameters, if required.

NOTE: If installing 01-9560 64K memory e528 Digital T ermostats, be aware t at t ese devices support t e

INNCOM ES-1 Flas Memory Module. T e ES-1 provides t e ability to copy HVAC related parameter settings

from a “golden” e528 t at as previously been installed in a room and ad its HVAC related parameters set

correctly and verified operationally wit t e HVAC equipment. Once t ese settings are copied to t e ES-1

module, plugging t e ES-1 into a new t ermostat automatically uploads t e settings.

Figure

Electrical Box Connections

Line and Low Voltage

Inhaltsverzeichnis

Andere Inncom Thermostat Handbücher

Inncom

Inncom e4 Bedienungs- und Wartungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Inncom e528 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken