4ENG
enrolment won’t be successful. This can happen for various
reasons: The ngerprint image was too small, the nger was
wet or dirty (Inokey can usually identify a ngerprint even
with wet and greasy ngers but in the enrolment phase it is
best to have clean hands). Every function is limited by a time
out. When a new nger is being enrolled one has 2 minutes to
complete the enrolment. Even if the function wasn’t conclud-
ed for some reason, there is no fear of misuse. The same nger
can be enrolled more than once. This is an advantage for the
people with damaged ngerprints. To store the nger more
than once decreases the possibility of recognition failure. It is
recommended that administrator lls the Administrator and
user list, which is enclosed to this manual, so that there is a
complete overview who is administrator, who are users, when
they were enrolled or deleted and which ngers are enrolled.
3. POWER MODE
Inokey has two kind of power modes. When power save mode
is active, the device turns o 15 s after each operation is com-
pleted. Wake up can be performed by pressing on any button
for 1 s, device will be ready to use in 0,4 s. After wake up, de-
vice is in freescan mode (is waiting for a ngerprint) for 15 s,
also all other operations can be performed after wake up. If
device is in constant power mode, it is always switched on and
ready to use. Default power mode is constant power mode.
Power mode switching procedure:
• The left button on the Inokey unit should be pressed for 20
s, (blue LED will start ashing after 3 s. Ignore that and keep
pushing the button) the green LED will start ashing after 20
s.
• Press both buttons for 2 s to choose power save mode or only
right button for 2 s to choose constant power mode.
• When power mode is chosen, green LED will ash and buzzer
will buzz 3 times if power save mode is chosen or green LED
will ash and buzzer will buzz one time if constant power is
chosen.
IMPORTANT:
Power mode can be chosen any time by anyone, also by per-
son which is not enrolled.When power save mode is activated,
device is using less power. When device is in constant power
mode it is using in average 1,8 W power, when it is in sleep
mode (power save), it is using in average 0,012 W power. By
choosing power save mode app. 15 kWh annually can be
saved and will increase device lifetime.
4. CHOOSING THE RELAY OUTPUT
Inokey has 2 relay outputs. When ngerprint is enroled, a
relay output, which will be triggered by this nger, must be
choosen. By pressing the adequate button, relay output will
be choosen. Left button relay 1, right button relay 2, both but-
tons at the same time relay 1 and 2.
5. ADMINISTRATOR’S ROLE AND
ADMINISTRATOR ENROLMENT
Only an administrator has the right to enrol or delete users.
Function buttons are found on the Inokey unit which is acces-
sible to anybody. It is therefore extremely important that only
an authorised person can execute the Inokey enrol and de-
lete functions. Inokey will save three administrator templates
(either three from a single person or one each from three
dierent people). Administration enrolment is simple. After
Inokeyis installed, the rst three ngerprints enrolled are as-
signed with administrative rights. When the Inokey is in frees-
can mode and administrator nger is detected, lock will be
triggered. Same as for normal user in case of positive match.
Administrator enrolment procedure:
• The left button on the Inokey unit should be pressed for 3
seconds.The blue LED will start ashing fast. Choose the relay,
green LED will follow.
• The administrator then presses his/her nger on the sensor
three times. After each successful sensor reading, short buzz
will be heard. If sensor reading is not successful (sensor area
coverage is too small), red LED will ash for 1 s. If sensor read-
ing is not successful nger must be pressed once again.
• When the administrator is correctly enrolled, the green LED
will ash and the buzzer will buzz one time.
• The same procedure is repeated with other two administra-
tive ngerprints.
IMPORTANT:
Administrative ngerprint templates can be erased only with
»delete all« function which also erases all other templates in
the memory. That’s why the administrator must be chosen
carefully, especially if the Inokey ngerprint reader is used by
more than a few people.
6. USER FINGER ENROLMENT
After the administrative templates are enrolled, pressing the
left button for 3 s on the Inokey unit will trigger the »enrol
user nger« function. The only right that a user has is trigger-
ing the lock in the event of positive ngerprint identication
and power mode selection function.
User nger enrolment procedure:
• The left button on the Inokey unit should be pressed for 3
seconds. The blue LED starts ashing.
• An administrator presses his/her nger on the sensor once.
