INSYS EloStar time Bedienungsanleitung
EloStar time
Handbuch
Version 1.03
1
EloStar time
User manual
EN 1300
M 102301
Class 2/B
EloStar time
Handbuch
Version 1.03
2
Table of contents
1. OPENING THE LOCK.................................................................................................................................... 3
2. LOCKING THE LOCK ................................................................................................................................... 4
3. PROGRAMMING THE LOCK ...................................................................................................................... 5
3.1.
R
EPROGRAMMING THE MASTER CODE
.......................................................................................................... 6
3.2.
R
EPROGRAMMING THE MASTER CODE WITH EMERGENCY OPENING LOCK
.................................................... 6
3.3.
P
ROGRAMMING USER CODES
........................................................................................................................ 7
3.4.
4-
EYES PRINCIPLE
......................................................................................................................................... 8
3.5.
S
ETTING THE OPENING DELAY
/
RELEASE TIME
.............................................................................................
3.6.
A
UTOMATIC LOCKING
................................................................................................................................ 10
3.7.
B
LOCKING
/
RELEASING THE LOCK
............................................................................................................. 11
3.8.
S
ETTING DATE AND TIME
............................................................................................................................ 12
3. .
P
ROGRAMMING WITH A
PC ........................................................................................................................ 13
3.10.
E
VENT LOG
............................................................................................................................................... 15
3.11.
R
EPROGRAMMING THE QUICK OPENING CODE
.......................................................................................... 15
3.12.
A
CTIVATING EXTERNAL INPUT AND OUTPUT SIGNALS
.............................................................................. 16
3.13.
C
ONNECTION OF THE EXTERNAL
LCDXT
DISPLAY
.................................................................................. 20
3.14.
R
ESETTING THE LOCK
............................................................................................................................... 21
4. APPENDIX ...................................................................................................................................................... 22
4.1.
O
PTICAL AND ACOUSTIC SIGNAL OUTPUTS
................................................................................................. 22
4.2.
N
OTES
........................................................................................................................................................ 22
4.3.
A
CCESSORY LIST
........................................................................................................................................ 23
EloStar time
Handbuch
Version 1.03
3
EloStar time
Safety notes
• Immediately change the factory-set master CODE 1 2 3 4 5 6 for security reasons.
• Do not use any personal data for your new CODE such as birthdays or other information that
could be guessed from knowledge about you.
•
After entering your new CODE, open and close the electronic lock se eral times with your PIN
and new CODE while the door is open.
•
You can always cancel an entry that you ha e started with the
C
key.
1. Open ng the lock
Open ng w th a code
0
Enter your user number (0 = master code)
123456
1
Enter the opening code
If a power interruption has occurred, e.g. battery change, the code has to be
entered tw ce.
If a signal sequence sounds after you ha e entered your user number, the lock is
blocked for access:
A time program is acti e
Lock blocked by master
Lock blocked by a connected burglar alarm system, for example
When the lock is open, the green LED flashes e ery second (only when the function
“Automatic locking after 10 sec.” is acti ated). In this state, all functions of the lock
can be programmed. (See Programming the lock)
EloStar time
Handbuch
Version 1.03
4
2. Lock ng the lock
Three options are pro ided for locking the lock:
Locking by pressing a key (default setting)
Locking ia door switch/boltwork switch
Automatic locking after 10 seconds
The lock is locked by pressing a key (except for C and * key) as the default setting. In
order to acti ate one of the two other options, the lock has to be programmed
correspondingly. The programming can either be done ia the keypad (see Chapter
3. Programming the lock) or ia the PC software CombiComm (not included in the
scope of supply).
Attention:
Before lea ing the safe deposit, it is imperati e to make sure that the lock is correctly
locked.
Further funct ons of EloStar time:
1 master code (6-d g t)
9 user codes
S lent alarm w th alarm t me delay
Automat c lock ng w th door sw tch
Automat c lock ng after 10 seconds
4-eyes pr nc ple
Open ng delay w th release t me
Block ng / releas ng lock
Event log w th the last 512 events
Date / t me
User-def ned t me programs
Qu ck open ng code
Programm ng v a PC
Resett ng the lock
EloStar time
Handbuch
Version 1.03
5
3. Programm ng the lock
In order for the lock to be programmed, it has to be opened. For this purpose, the
lock can be opened with any user code.
In the deli ery state, the lock can only be opened with the factory master code
(0 = user no. + 1 2 3 4 5 6 = master code,
0 123456
).
The most important functions of the lock can be programmed with the keypad;
extended functions are programmed with the PC software CombiComm and the
e ent log is read out with the PC software.
Programm ng w th the keypad
Program number Funct on
0
Reprogram the master code
1
Program/reprogram/delete user codes
2
Acti ate the 4-eyes principle
3
Set the opening delay / release time
4
Set automatic locking after 10 sec.
5
Reset lock
6
Block / release lock
7
Start programming ia PC
8
Set date and time
9
Set IO functions / set blocking element
EloStar time
Handbuch
Version 1.03
6
3.1. Reprogramming the master code
Notes:
• Immediately change the factory-set code 1 2 3 4 5 6 for security reasons.
• The programming can only be done when the lock is open.
• Do not use any personal data for your new code such as birthdays or other
information that could be guessed from knowledge about you.
• After you ha e entered the new code, open and close the electronic lock
se eral times with the new code while the door is open.
*0*
Enter the program number
123456 *
1
Enter the old master code
654321 *
Enter the new master code
654321 *
1
Enter the new master code
3.2. Reprogramming the master code with emergency opening lock
In conjunct on w th an emergency open ng lock, the master code can be
reprogrammed w thout knowledge of the current master code. The emergency
open ng lock must be open for th s.
*0*
Enter the program number
654321 *
Enter the new master code
654321 *
1
Enter the new master code
EloStar time
Handbuch
Version 1.03
7
3.3. Programming ser codes
Note:
• The programming can only be done when the lock is open.
• Do not use any personal data for your new code such as birthdays or other
information that could be guessed from knowledge about you.
• After you ha e entered the new code, open and close the electronic lock
se eral times with the new code while the door is open.
• The programming or deletion of user codes is sa ed in the e ent log. (For
reading out the e ent log, see the manual of the PC software CombiComm)
Programm ng or creat ng a new user code
*1*
Enter program number 1
1*
Enter the user number (e.g. user 1)
123456 *
1
Enter the master code
111111 *
Enter the new user code
111111 *
1
Enter the new user code
Reprogramm ng the user code
*1*
Enter program number 1
1*
Enter the user number (e.g. user 1)
111111 *
1
Enter the master code or old user code
132132 *
Enter the new user code
132132 *
1
Enter the new user code
Delet ng a user code
*1*
Enter program number 1
1*
Enter the user number (e.g. user 1)
123456 *
1
Enter the master code
*
1
Delete
Note:
When the 4-eyes principle is acti ated, it is not possible to delete all users;
at least one user must be programmed.
EloStar time
Handbuch
Version 1.03
8
3.4. 4-eyes principle
Notes:
• The 4-eyes principle can only be set with the master code.
• This setting can only be made when the lock is open. After this function has
been programmed (acti ated), the lock can only be opened when two codes
are entered.
• The programming or deletion of the 4-eyes principle is sa ed in the e ent log.
(For reading out the e ent log, see the manual of the PC software
CombiComm)
• In addition to the master code, at least one user code must be programmed.
Act vat ng the 4-eyes pr nc ple
*2*
Enter program number 2
123456 *
Enter the master code
1*
1
Acti ate the 4-eyes principle
Delet ng the 4-eyes pr nc ple
*2*
Enter program number 2
123456 *
Enter the master code
0*
1
Delete the 4-eyes principle
Open ng w th the 4-eyes pr nc ple
1 010101
1
Enter the user number of the first code (e.g. 1) and
enter the first code (e.g. 010101)
1
Green LED is lit.
2 020202
1
Enter the user number of the second code (e.g. 2) and
enter the second code (e.g. 020202)
EloStar time
Handbuch
Version 1.03
3.5. Setting the opening delay / release time
Notes:
• The opening delay can only be programmed by the master.
• The programming can only be done when the lock is open.
• The programming or deletion of the opening delay and release time is sa ed in
the e ent log. (For reading out the e ent log, see the manual of the PC
software CombiComm)
Sett ng the open ng delay and release t me
*3*
Enter the program number
123456 *
1
Enter the master code
01*
Set an opening delay, e.g. 01 min.
01*
1
Set a release time, e.g. 01 min.
The opening delay can be set in the range of 01 – 99 minutes.
The release time can be set in the range of 01 – 15 minutes. When 00 is entered, the
lock immediately opens after the opening delay has expired, without an additional
code entry or expiration of a release time.
Delet ng the open ng delay and release t me
*3*
Enter the program number
123456 *
1
Enter the master code
00*
Delete the opening delay
00*
1
Delete the release time
Open ng w th open ng delay and release t me
1 010101
1
Enter the user number of the first code (e.g. 1) and
enter the first code (e.g. 010101)
(in the case of the 4-eyes principle, enter the second code
as well).
1
Expiration of the opening delay. The green LED flashes
e ery 5 seconds. After the time delay has expired, this is
signaled by the signal tone 15x. The green LED is lit. The
lock waits for the opening code to be entered again during
the release time.
1 010101
1
Enter the user number of the code (e.g. 1) and
enter the first code (e.g. 010101).
Lock opens. (Only one code is required, e en with
the 4-eyes principle!)
EloStar time
Handbuch
Version 1.03
10
3.6. A tomatic locking
Notes:
• Automatic locking can only be set by the master.
• After this function has been acti ated, the lock automatically locks 10 seconds
after it was opened.
• The programming can only be done when the lock is open.
• The programming or deletion of the opening delay and release time is sa ed in
the e ent log. (For reading out the e ent log, see the manual of the PC
software CombiComm)
Act vat ng automat c lock ng
*4*
Enter the program number
123456 *
1
Enter the master code
1*
1
Acti ate automatic locking
Delet ng automat c lock ng
*4*
Enter the program number
123456 *
1
Enter the master code
0*
1
Delete automatic locking
Inhaltsverzeichnis
Andere INSYS Türschloss Handbücher
