Intel 5000 Series Bedienungsanleitung

Intel®5000 Sequence Processor

Integration

Warning, Important Safety Instructions

System power on/off: The power button DOES NOT turn off the system AC power. To remove power

from system, you must unplug the AC power cord from the wall outlet. Make sure the AC power cord is

unplugged before you open the chassis, add, or remove any components.

Hazardous conditions, devices and cables: Hazardous electrical conditions may be present on power,

telephone, and communication cables. Turn off the server workstation and disconnect the power cord,

telecommunications systems, networks, and modems attached to the server workstation before opening

it. Otherwise, personal injury or equipment damage can result.

Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives, boards, and other

parts. We recommend that you perform all procedures in this chapter only at an ESD workstation. If one

is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis

ground any unpainted metal surface on your server workstation when handling parts.

ESD and handling boards: Always handle boards carefully. They can be extremely sensitive to ESD.

Hold boards only by their edges. After removing a board from its protective wrapper or from the server

workstation , place the board component side up on a grounded, static free surface. Use a conductive

foam pad if available but not the board wrapper. Do not slide board over any surface.

Installing the Processor

Note:

• Do not touch the contacts on either the processor or the processor socket.

• Do not force the processor socket into place. When correctly aligned, the socket will easily drop

into place.

To install a processor, follow these instructions:

1. Observe safety and ESD precautions.

2. Turn off all peripheral devices connected to the server. Turn off the server.

3. Disconnect the AC power cord from the server.

4. Remove the chassis cover. See the documentation that came with your chassis for instructions

on removing the cover.

5. Locate the processor sockets (see Figure 1).

Figure 1. Example: Locating Processor Sockets.

Note: Consult Your Board Documentation for Proper Socket Location

6. Disconnect and remove any components necessary to access the processor sockets. See the

documentation that came with your chassis for instructions on removing chassis components.

7. Push down on the lever attached to the processor socket. While holding the lever down, pull it

towards the center of the board to disengage the lever from the hook. Fully open the lever. See

Figure 2.

Figure 2. Opening Processor Socket Lever

8. Push down on the rear tab of the load plate to swing the front of the load plate up slightly. Fully

open the load plate. See Figure 3.

Figure 3. Opening Load Plate

9. If the protective cover is attached from the load plate, remove it and store it for future use. See

Figure 4.

Figure 4. Removing Protective Cover from Load Plate

10. Remove the processor from the box and remove the protective shipping cover.

11. Set the processor in the socket with the processor cutouts matching the processor socket

notches. See Figure 5.

Figure 5. Setting Processor in Place

12. Close the load plate.

13. Close the socket lever. Push downward on the socket lever while pushing it toward the center of

the processor socket to engage it under the hook on the processor socket.

Installing the Heat Sink(s)

Note: The heat sink has thermal interface material (TIM) located on the bottom of it. Use

caution when handling the heat sink so you do not damage the TIM.

Each processor requires a heat sink. Depending on your chassis, you may need to use

either a active (Figure 6) or an passive heat sink (Figure 7). An active heat sink has a fan

attached to the top of it and a cable that needs to be connected to the server board.

AF000099

Figure 6. Active Heat Sink (Cable Not Shown)

Use the following steps to install a heat sink.

1. Set the heat sink over the processor, lining up the four captive screws with the four posts

surrounding the processor.

2. Loosely screw in the captive screws on the heat sink corners in the order shown by Figure 7.

Do not fully tighten one screw before loosely attaching the others.

3. In the same order, gradually and equally tighten each captive screw until each is firmly

tightened. Do not fully tighten one screw at a time.

Figure 7. Installing Heat Sink (Passive Heat Sink Shown)

4. Active heat sink only: Connect the heat sink cable to the server board. Reference you board

documentation for proper fan header location.

5. Reinstall and reconnect any parts you removed or disconnected to reach the processor sockets.

See the documentation that came with your chassis for instructions on installing chassis

components.

6. Replace the chassis cover and reconnect the AC power cord. See the documentation that came

with your chassis for instructions on installing the cover.

Andere Handbücher für 5000 Series

Inhaltsverzeichnis

Andere Intel Computerhardware Handbücher

Intel

Intel 460GX Bedienungsanleitung

Intel

Intel LGA1155 SOCKET - THERMAL MECHANICAL S AND DESIGN GUIDELINES... Bedienungsanleitung

Intel

Intel E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core... Bedienungsanleitung

Intel

Intel Xeon X5570 Bedienungsanleitung

Intel

Intel Pentium 4 Kurzanleitung

Intel

Intel 5100 Series Bedienungsanleitung

Intel

Intel E7500 Leitfaden

Intel

Intel 6300ESB ICH Bedienungsanleitung

Intel

Intel BX80569Q9550 - Core 2 Quad 2.83 GHz... Bedienungsanleitung

Intel

Intel Core i7-860 Bedienungs- und Sicherheitshinweise

Intel

Intel 852GM - Leitfaden

Intel

Intel NetStructure ZT 5515 Betriebsanleitung

Intel

Intel RS25AB080 Bedienungsanleitung

Intel

Intel SROMBSASMR Installationshandbuch

Intel

Intel 80C186EA Betriebsanleitung

Intel

Intel SRCZCR - RAID Controller Storage Bedienungsanleitung

Intel

Intel ETHEREXPRESS PRO/100 Technisches Handbuch

Intel

Intel CORE 2 DUO E4000 - 3-2008 Bedienungsanleitung

Intel

Intel SRCSASJV - RAID Controller Installationshandbuch

Intel

Intel EP80579 Bedienungsanleitung

Intel

Intel 82496 CACHE CONTROLLER Bedienungsanleitung

Intel

Intel 80302 Technisches Handbuch

Intel

Intel I5 3570K Bedienungsanleitung

Intel

Intel Xeon Phi Processor x200 Leitfaden

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung