Intel 430TX Bedienungsanleitung
Intel 430TX PCI Chipset
Intelligent
MAIN BOARD
ATX586
for
Dual CPUs ATX Factor
TX2
for
AT Factor / Wide SCSI
USER’S MANUAL
version 1.0
2
UPDATE INFORAMTION
JULY 22, 97
1) When you install ATX power supply, please connect CASE
STANDBY to front panel connector CN9/JP9 , pin 19-20
Power On. Then turn on ATX power supply.
2) The difference between TX2 and TX3 is that TX3 is without
SCSI port/chip. Others are the same.
3
CONTENT
Preface .................................................................. 1
CHAPTER 1 Hardware Installation for
ATX586 4
1.1 One Jumper to Set CPU.....................…4
1.2 Two Jumper to Set CPU.........…………… 6
1.3 Other Hardware
Jumpers......................... 7
1.4 Install System DRAM
Memory............... 8
1.5 Install IDE, I/O and Front
Panel........…….10
1.6 I/O Address And
IRQ................................ 12
1.7 Jumpers
List............................................. 12
1.8 Pin Definition for Cable
Connection........ 13
CHAPTER 2 PNP BIOS
SETUP....................... 15
2.1 BIOS
Setup............................................... 15
2.2 Standard
Setup......................................... 15
2.3 BIOS Features
Setup............................... 16
2.4 Chipset Features
Setup............................ 17
2.5 Power Management
Setup....................... 17
4
2.6 PNP/PCI
Configuration............................. 18
2.7 Integrated
Peripherals.............................. 18
2.8 AWARD BIOS Post
Code......................... 19
CHAPTER 3 EIDE & FLASH BIOS
SETUP...... 24
Part I. Installation Ultra EIDE
Driver............... 24
Part II. Update Flash
BIOS............................. 48
5
CHAPTER 4 Hardware Installation for TX2 49
4.1 One Jumper to Set CPU.....................…50
4.2 Two Jumper to Set CPU.........…………… 52
4.3 Other Hardware
Jumpers......................... 53
4.4 Install System DRAM
Memory............... 54
4.5 Install IDE, I/O and Front
Panel........…….56
4.6 I/O Address And
IRQ................................ 58
4.7 Jumpers
List............................................. 58
4.8 Pin Definition for Cable
Connection........ 59
6
Preface
Inside the Document
This document describes setup ATX586 Dual Pentium Main Board with
Intel 430TX PCI CHIPSET, resulting in Ultra IDE performance.
ATX586 is for ATX platform with dual processors design, including
Enhance I/O chip (SMC 669 compatible). There is an option that
installing “82093AA”supports two Intel Pentium (MMX) CPU, said
Dual Processors. Under single processor, the user installs Intel
Pentium 75-233Mhz, MMX, AMD K5/K6-PR 233, CYRIX CX6x86 200+.
Excepting above mentioned, ATX586 is designed with Auto
Switching between 3.3v and 2.8v CPU (when you use single CPU
only), front panel connector and Smart Jumper Setting for
different CPU.
The package for ATX586 including:
þATX586 mother board
þTwo IDE drive ribbon cable for 4 devices
þOne Floppy ribbon cable for 2 devices
þOne Ultra IDE device disk
þThis user’s manual
Chapter 1 is about positions, jumpers and connectors for
ATX586. Due to the board supports full range of Pentium CPU MMX
75Mhz-233Mhz, AMD K5/K6-PR233, CYRIX 6x86 CX 200+.
Chapter 2 is for BIOS setup. If you want to use external I/O card,
you can disable the I/O function in BIOS and then install a card on slot.
You also modify the COM1 and COM2 as COM3 and COM4 in
BIOS. Finally, the BIOS is PnP function. It auto detects the PCI
IRQ, ISA IRQ and HDD mode. Chapter 3 is for IDE DRIVER
installation and how to upgrade BIOS.
7
(Chapter 4 is about positions, jumpers and connectors for TX2.
Due to the board supports full range of Pentium CPU MMX 75Mhz-
233Mhz, AMD K5/K6-PR233, CYRIX 6x86 CX 200+.)
Simple features:
²Intel 430 TX PCISET. 82439TX System Controller (MTXC),
82371AB PIIX4 PCI to ISA / IDE Xcelerator, 82093AA I/O
Advanced Programmable Interrupt Controller (IOAPIC).
²Compatible SMC 669 super I/O on board.
²Supports full range of Pentium Processor Family, up to Intel
Pentium MMX-233Mhz, AMD K6-PR-233, CX 6x86 200+. There
is an auto- switching mode from 3.3v to 2.8v.
²Installing (option) 82093AA to let the board supports two
Intel Pentium or MMX CPU at the same board for ATX586.
It is perfect to run the same voltage CPU!
²Support SDRAM/EDO/Fast page DRAM, 72-pin SIMM socket *
4pcs, 168-pin DIMM socket * 2pcs. 2 pairs/4 banks up to
256MB. 6-1-1-1 for SDRAM; 5-2-2-2 for EDO; 6-3-3-3 for FP.
²64-MB DRAM cacheability. Direct Mapped organization-write
back only. Supports 256K and 512K Pipelined Burst SRAM.
²PCI V2.1 compatible. Concurrent PCI, enhanced CPU/PCI/ISA
performance.
²Provides Multiprocessor Interrupt Management: dynamic interrupt
distribution routing interrupt to the lowest priority processor;
software programmable control of interrupt inputs; off loads
interrupt related traffic from the memory bus.
8
²24 Programmable Interrupts: 13 ISA supported; 4 PCI; 1 interrupt/
SMI# rerouting; 2 motherboard ; 1 interrupt used for INTR input; 3
general purpose; independently programmable for edge/level
sensitivity interrupts; each interrupt can be programmed to
respond to active high or low inputs.
²4 * 32-bit PCI, 4 * 16 bit ISA Slots for ATX586
²2 * Ultra EIDE,support 4 IDE devices. EPP/ECP/SPP printer port.
2 * 16550 UART serial ports. PS/2 mouse port. IR, infrared, port,
option for FIR, fast infrared. 2 * USB, universal serial bus, ports.
²IDE controller: Independent timing of up to 4 drives. PIO mode
4 transfers up to 14 Mbytes/sec. Supports “Ultra 33”synchronous
DMA mode transfers up to 33 Mbytes/sec. Integrated 8*32-bit
buffer for IDE PCI Burst transfers.
²Dual Power Supply. Has both AT and ATX power connectors
on board to support AT or ATX power supply with soft-on/off
features.
²Built-in AWARD PCI/ISA Plug and Play Flash BIOS GREEN
BIOS
²Two-mega flash recovery BIOS ROM.
&&&
9
Chapter 1
Hardware
Installation For ATX586
1.1 One Jumper to Set CPU , Simple Jumper
No more CPU jumper setting when you use Single Processor
Intel 133Mhz,
CYRIX 166+,
AMD K5-133 CPU.
You just install CPU directly and Power On. (At the moment, JP6: 1-
2 and JP7: 2-3 SHORT; JP8/JP9: 1-2 SHORT )
A: Using Intel CPU (Ensuring JP8/JP9: 1-2 SHORT)
CPU Speed JP6 JP7
Intel 100Mhz 1-2 SHORT 1-2 SHORT
Intel 166Mhz 2-3 SHORT 2-3 SHORT
Intel 200Mhz 2-3 SHORT 1-2 SHORT
Intel 233Mhz 1-2 SHORT 1-2 SHORT
B: Using AMD K5/K6 (Ensuring JP8/9: 1-2 SHORT)
CPU Speed JP6 JP7
AMD K5-100 1-2 SHORT 1-2 SHORT
AMD K5/K6-PR-166 2-3 SHORT 2-3 SHORT
AMD K6-PR200 2-3 SHORT 1-2 SHORT
AMD K6-PR233 1-2 SHORT 1-2 SHORT
C: Using CYRIX 6x86 CPU ( Ensuring JP6: 1-2 and JP7: 2-3 SHORT)
CPU Speed JP8 JP9
CX 133+, 55Mhz 2-3 SHORT 2-3 SHORT
CX 150+, 60Mhz 2-3 SHORT 1-2 SHORT
CX 200+, 75Mhz 1-2 SHORT 2-3 SHORT
When you want to install two CPU, they are perfect are the same
voltage 2.8v (P55C) or 3.3v(P54C). Different voltage can’t be
used together. Installing the 1st CPU at U4 socket!
10
Map of ATX586 Mother Board
Default Setting for Intel Pentium 133Mhz,
AMD K5-133,CYRIX P166+,512K PB Cache
1.2 Two-Jumper Setting for CPU
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Intel Hauptplatine Handbücher
Intel
Intel D33217CK Bedienungsanleitung
Intel
Intel BLKD410PTL Bedienungsanleitung
Intel
Intel PM945GC-478 Bedienungsanleitung
Intel
Intel Desktop Board D915PCM Bedienungsanleitung
Intel
Intel BOXDG43NB Bedienungsanleitung
Intel
Intel BLKDG31GL Konfigurationshandbuch
Intel
Intel DB43LD Bedienungsanleitung
Intel
Intel BLKD945GCLF - MB 533FSB DDR2 667 533 Aud+Vdo+Lan... Konfigurationshandbuch
Intel
Intel D915PBL - 915P Socket 775 ATX Motherboard Bedienungsanleitung
Intel
Intel D925XHY Bedienungsanleitung
Intel
Intel P35 Bedienungsanleitung
Intel
Intel BLKDX79SI Konfigurationshandbuch
Intel
Intel SE7210TP1-E - Socket 478 ATX Server... Bedienungsanleitung
Intel
Intel D815EGEWLU - P3 Socket 370 MicroATX... Bedienungsanleitung
Intel
Intel BOXDP67BG Bedienungsanleitung
Intel
Intel D945GCPE - Desktop Board Motherboard Bedienungsanleitung
Intel
Intel DH55TC Bedienungsanleitung
Intel
Intel DP43BF Bedienungsanleitung
Intel
Intel BLKD945GCLF2 Bedienungsanleitung
Intel
Intel BOXD945PAWLK - Desktop Board D945PAW Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
