Intel SC5300 Bedienungsanleitung

Intel® Server Chassis SC5300, SC5300

LX and SC5300 BRP

User Guide

A Guide for Technically Qualified Assemblers of Intel® Identified

Subassemblies/Products

Order Number: C51486-001

ii Intel® Server Chassis SC5300 User Guide

Disclaimer

Information in this document is provided in connection with Intel®products. No license, express or implied, by estoppel or

otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel’s Terms and Conditions

of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating

to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability,

or infringement of any patent, copyright or other intellectual property right. Intel products are not designed, intended or

authorized for use in any medical, life saving, or life sustaining applications or for any other application in which the failure of

the Intel product could create a situation where personal injury or death may occur. Intel may make changes to

specifications and product descriptions at any time, without notice.

Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.”

Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising

from future changes to them. This document contains information on products in the design phase of development. Do not

finalize a design with this information. Revised information will be published when the product is available. Verify with your

local sales office that you have the latest datasheet before finalizing a design.

Intel server boards contain a number of high-density VLSI and power delivery components that need adequate airflow for

cooling. Intel’s own chassis are designed and tested to meet the intended thermal requirements of these components when

the fully integrated system is used together. It is the responsibility of the system integrator that chooses not to use Intel

developed server building blocks to consult vendor datasheets and operating parameters to determine the amount of airflow

required for their specific application and environmental conditions. Intel Corporation can not be held responsible if

components fail or the server board does not operate correctly when used outside any of their published operating or non-

operating limits.

Intel, Intel Pentium, and Intel Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the

United States and other countries.

*Other names and brands may be claimed as the property of others.

Preface

Intel® Server Chassis SC5300 User Guide iii

Preface

About this Manual

Thank you for purchasing and using the Intel®Server Chassis SC5300.

This manual is written for system technicians who are responsible for troubleshooting, upgrading,

and repairing this server chassis. This document provides a brief overview of the features of the

board/chassis, a list of accessories or other components you may need, troubleshooting information,

and instructions on how to add and replace components on the Intel® Server Chassis SC5300. For

the latest version of this manual, refer to

http://support.intel.com/support/motherboards/server/chassis/SC5300.

Manual Organization

Chapter 1 provides a brief overview of the Server Chassis SC5300. In this chapter, you will find a

list of the server chassis features, photos of the product, and product diagrams to help you identify

components and their locations.

Chapter 2 provides instructions on adding and replacing components. Use this chapter for step-by-

step instructions and diagrams for installing or removing components such as the front bezel,

floppy drive, peripheral drives, and other components.

Chapter 3 provides information on maintaining your server. In this chapter, you will find step-by-

step instructions and diagrams for replacing fans, power supply and other components.

Chapter 4 provides technical reference information. In this chapter, you will find information on

power supply and system environmental specifications.

Product Accessories

The server chassis is compatible with the following Intel®Server Boards:

 Intel® Server Board SE7525GP2

 Intel® Server Board SE7320SP2

 Intel® Server Board SE7520BD2

 Intel® Server Board SE7520AF2

For information about which items have been tested and can be used with your chassis, and for

ordering information for Intel products, see

http://support.intel.com/support/motherboards/server//chassis/SC5300/compat.htm.

Preface

iv Intel® Server Chassis SC5300 User Guide

Additional Information and Software

If you need more information about this product or information about the accessories that can be

used with this server chassis, use the following resources:

For in-depth technical information about this

product, including BIOS settings and chipset

information

Intel® Server Chassis SC5300 Technical Product

Specification at

http://support.intel.com/support/motherboards/server/chassis/

sc5300/sb/CS-012478.htm.

If you just received this product and need to

install it Intel® Server Chassis SC5300 Quick Start User’s Guide in

the product box

For the latest product information http://support.intel.com/support/motherboards/server/chassis/

SC5300

Accessories or other Intel server products http://support.intel.com/support/motherboards/server/sb/CS-

012636.htm

Hardware (peripheral boards, adapter cards)

and operating systems that have been

tested with this product

http://support.intel.com/support/motherboards/server/chassis/

sc5300/compat.htm

Server boards that are compatible with this

chassis http://support.intel.com/support/motherboards/server/sb/CS-

012479.htm

For virtual system tours and interactive

repair information http://developer.intel.com/design/servers/smarttool/index.htm

Preface

Intel® Server Chassis SC5300 User Guide v

Safety Information

WARNING

Before working with your server product, whether you are using this guide or any other

resource as a reference, pay close attention to the safety instructions. You must adhere to the

assembly instructions in this guide to ensure and maintain compliance with existing product

certifications and approvals. Use only the described, regulated components specified in this

guide. Use of other products / components will void the UL listing and other regulatory

approvals of the product and will most likely result in noncompliance with product

regulations in the region(s) in which the product is sold.

Emissions Disclaimer

To ensure EMC compliance with your local regional rules and regulations, the final configuration

of your end system product may require additional EMC compliance testing. For more information

please contact your local Intel Representative.

See “Regulatory and Integration Information” for product Safety and EMC regulatory compliance

information. This is an FCC Class A device. Integration into a Class B chassis does not result in a

Class B device.

Intended Uses

This product was evaluated as Information Technology Equipment (ITE), which may be installed in

offices, schools, computer rooms, and similar commercial type locations. The suitability of this

product for other product categories and environments (such as: medical, industrial,

telecommunications, NEBS, residential, alarm systems, test equipment, etc.), other than an ITE

application, may require further evaluation.

EMC Testing

Before computer integration, make sure that the chassis, power supply, and other modules have

passed EMC testing using a server board with a microprocessor from the same family (or higher)

and operating at the same (or higher) speed as the microprocessor used on this server board.

Warnings

System power on/off: The power button DOES NOT turn off the system

AC power. To remove power from system, you must unplug the AC power

cord from the wall outlet. Make sure the AC power cord is unplugged before

you open the chassis, add, or remove any components.

Hazardous conditions, devices and cables:Hazardous electrical

conditions may be present on power, telephone, and communication cables.

Turn off the server and disconnect the power cord, telecommunications

systems, networks, and modems attached to the server before opening it.

Otherwise, personal injury or equipment damage can result.

Electrostatic discharge (ESD) and ESD protection: ESD can

damage disk drives, boards, and other parts. We recommend that you

perform all procedures in this chapter only at an ESD workstation. If one is

not available, provide some ESD protection by wearing an antistatic wrist

Preface

vi Intel® Server Chassis SC5300 User Guide

strap attached to chassis groundany unpainted metal surfaceon your

server when handling parts.

ESD and handling boards: Always handle boards carefully. They can

be extremely sensitive to ESD. Hold boards only by their edges. After

removing a board from its protective wrapper or from the server, place the

board component side up on a grounded, static free surface. Use a

conductive foam pad if available but not the board wrapper. Do not slide

board over any surface.

Installing or removing jumpers: A jumper is a small plastic encased

conductor that slips over two jumper pins. Some jumpers have a small tab on

top that you can grip with your fingertips or with a pair of fine needle nosed

pliers. If your jumpers do not have such a tab, take care when using needle

nosed pliers to remove or install a jumper; grip the narrow sides of the

jumper with the pliers, never the wide sides. Gripping the wide sides can

damage the contacts inside the jumper, causing intermittent problems with

the function controlled by that jumper. Take care to grip with, but not

squeeze, the pliers or other tool you use to remove a jumper, or you may

bend or break the stake pins on the board.

Safety Cautions

Read all caution and safety statements in this document before performing any of the instructions.

See also http://support.intel.com/support/motherboards/server/sb/CS-010770.htm .

The power supply in this product contains no user-serviceable parts. There may be more

than one supply in this product. Refer servicing only to qualified personnel.

Do not attempt to modify or use the supplied AC power cord if it is not the exact type

required. A product with more than one power supply will have a separate AC power cord

for each supply.

The power button on the system does not turn off system AC power. To remove AC power

from the system, you must unplug each AC power cord from the wall outlet or power supply.

The power cord(s) is considered the disconnect device to the main (AC) power. The socket

outlet that the system plugs into shall be installed near the equipment and shall be easily

accessible.

SAFETY STEPS: Whenever you remove the chassis covers to access the inside of the

system, follow these steps:

1. Turn off all peripheral devices connected to the system.

2. Turn off the system by pressing the power button.

3. Unplug all AC power cords from the system or from wall outlets.

4. Label and disconnect all cables connected to I/O connectors or ports on the back of the

system.

5. Provide some electrostatic discharge (ESD) protection by wearing an antistatic wrist

Preface

Intel® Server Chassis SC5300 User Guide vii

strap attached to chassis ground of the system—any unpainted metal surface—when

handling components.

6. Do not operate the system with the chassis covers removed.

After you have completed the six SAFETY steps above, you can remove the system covers.

To do this:

1. Unlock and remove the padlock from the back of the system if a padlock has been

installed.

2. Remove and save all screws from the covers.

3. Remove the covers.

For proper cooling and airflow, always reinstall the chassis covers before turning on the

system. Operating the system without the covers in place can damage system parts. To

install the covers:

1. Check first to make sure you have not left loose tools or parts inside the system.

2. Check that cables, add-in boards, and other components are properly installed.

3. Attach the covers to the chassis with the screws removed earlier, and tighten

them firmly.

4. Insert and lock the padlock to the system to prevent unauthorized access inside

the system.

5. Connect all external cables and the AC power cord(s) to the system.

A microprocessor and heat sink may be hot if the system has been running. Also, there may

be sharp pins and edges on some board and chassis parts. Contact should be made with

care. Consider wearing protective gloves.

Danger of explosion if the battery is incorrectly replaced. Replace only with the same or

equivalent type recommended by the equipment manufacturer. Dispose of used batteries

according to manufacturer’s instructions.

The system is designed to operate in a typical office environment. Choose a site that is:

Clean and free of airborne particles (other than normal room dust).

Well ventilated and away from sources of heat including direct sunlight.

Away from sources of vibration or physical shock.

Isolated from strong electromagnetic fields produced by electrical devices.

In regions that are susceptible to electrical storms, we recommend you plug your system into

a surge suppresser and disconnect telecommunication lines to your modem during an

electrical storm.

Provided with a properly grounded wall outlet.

Provided with sufficient space to access the power supply cord(s), because they serve as the

product’s main power disconnect.

Preface

viii Intel® Server Chassis SC5300 User Guide

Wichtige Sicherheitshinweise

Lesen Sie zunächst sämtliche Warn- und Sicherheitshinweise in diesem Dokument, bevor Sie eine

der Anweisungen ausführen. Beachten Sie hierzu auch die Sicherheitshinweise zu Intel-

Serverplatinen und -Servergehäusen unter

http://support.intel.com/support/motherboards/server/sb/CS-010770.htm .

Benutzer können am Netzgerät dieses Produkts keine Reparaturen vornehmen. Das

Produkt enthält möglicherweise mehrere Netzgeräte. Wartungsarbeiten müssen von

qualifizierten Technikern ausgeführt werden.

Versuchen Sie nicht, das mitgelieferte Netzkabel zu ändern oder zu verwenden, wenn es

sich nicht genau um den erforderlichen Typ handelt. Ein Produkt mit mehreren Netzgeräten

hat für jedes Netzgerät ein eigenes Netzkabel.

Der Wechselstrom des Systems wird durch den Ein-/Aus-Schalter für Gleichstrom nicht

ausgeschaltet. Ziehen Sie jedes Wechselstrom-Netzkabel aus der Steckdose bzw. dem

Netzgerät, um den Stromanschluß des Systems zu unterbrechen.

SICHERHEISMASSNAHMEN: Immer wenn Sie die Gehäuseabdeckung abnehmen um an

das Systeminnere zu gelangen, sollten Sie folgende Schritte beachten:

1. Schalten Sie alle an Ihr System angeschlossenen Peripheriegeräte aus.

2. Schalten Sie das System mit dem Hauptschalter aus.

3. Ziehen Sie den Stromanschlußstecker Ihres Systems aus der Steckdose.

4. Auf der Rückseite des Systems beschriften und ziehen Sie alle Anschlußkabel von den

I/O Anschlüssen oder Ports ab.

5. Tragen Sie ein geerdetes Antistatik Gelenkband, um elektrostatische Ladungen (ESD)

über blanke Metallstellen bei der Handhabung der Komponenten zu vermeiden.

6. Schalten Sie das System niemals ohne ordnungsgemäß montiertes Gehäuse ein.

Nachdem Sie die oben erwähnten ersten sechs SICHERHEITSSCHRITTE durchgeführt

haben, können Sie die Abdeckung abnehmen, indem Sie:

1. Öffnen und entfernen Sie die Verschlußeinrichtung (Padlock) auf der Rückseite des

Systems, falls eine Verschlußeinrichtung installiert ist.

2. Entfernen Sie alle Schrauben der Gehäuseabdeckung.

3. Nehmen Sie die Abdeckung ab.

Zur ordnungsgemäßen Kühlung und Lüftung muß die Gehäuseabdeckung immer wieder vor

dem Einschalten installiert werden. Ein Betrieb des Systems ohne angebrachte Abdeckung

kann Ihrem System oder Teile darin beschädigen. Um die Abdeckung wieder anzubringen:

1. Vergewissern Sie sich, daß Sie keine Werkzeuge oder Teile im Innern des Systems

zurückgelassen haben.

2. Überprüfen Sie alle Kabel, Zusatzkarten und andere Komponenten auf

ordnungsgemäßen Sitz und Installation.

3. Bringen Sie die Abdeckungen wieder am Gehäuse an, indem Sie die zuvor gelösten

Schrauben wieder anbringen. Ziehen Sie diese gut an.

4. Bringen Sie die Verschlußeinrichtung (Padlock) wieder an und schließen Sie diese, um

ein unerlaubtes Öffnen des Systems zu verhindern.

5. Schließen Sie alle externen Kabel und den AC Stromanschlußstecker Ihres S

stems

Preface

Intel® Server Chassis SC5300 User Guide ix

wieder an.

Der Mikroprozessor und der Kühler sind möglicherweise erhitzt, wenn das System in Betrieb

ist. Außerdem können einige Platinen und Gehäuseteile scharfe Spitzen und Kanten

aufweisen. Arbeiten an Platinen und Gehäuse sollten vorsichtig ausgeführt werden. Sie

sollten Schutzhandschuhe tragen.

Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur

durch denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp

ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers

entsprechend.

Das System wurde für den Betrieb in einer normalen Büroumgebung entwickelt. Der

Standort sollte:

sauber und staubfrei sein (Hausstaub ausgenommen);

gut gelüftet und keinen Heizquellen ausgesetzt sein (einschließlich direkter

Sonneneinstrahlung);

keinen Erschütterungen ausgesetzt sein;

keine starken, von elektrischen Geräten erzeugten elektromagnetischen Felder aufweisen;

in Regionen, in denen elektrische Stürme auftreten, mit einem Überspannungsschutzgerät

verbunden sein; während eines elektrischen Sturms sollte keine Verbindung der

Telekommunikationsleitungen mit dem Modem bestehen;

mit einer geerdeten Wechselstromsteckdose ausgerüstet sein;

über ausreichend Platz verfügen, um Zugang zu den Netzkabeln zu gewährleisten, da der

Stromanschluß des Produkts hauptsächlich über die Kabel unterbrochen wird.

重要安全指导

在执行任何指令之前，请阅读本文档中的所有注意事项及安全声明。和/或http://support.intel

.com/support/motherboards/server/sb/CS-010770.htm 上的

Intel Server Boards and Server

Chassis Safety Information

（《Intel 服务器主板与服务器机箱安全信息》）。

Preface

x Intel® Server Chassis SC5300 User Guide

Consignes de sécurité

Lisez attention toutes les consignes de sécurité et les mises en garde indiquées dans ce document

avant de suivre toute instruction. Consultez Intel Server Boards and Server Chassis Safety

Information sur le site http://support.intel.com/support/motherboards/server/sb/CS-010770.htm .

Le bloc d'alimentation de ce produit ne contient aucune pièce pouvant être réparée par

l'utilisateur. Ce produit peut contenir plus d'un bloc d'alimentation. Veuillez contacter un

technicien qualifié en cas de problème.

Ne pas essayer d'utiliser ni modifier le câble d'alimentation CA fourni, s'il ne correspond pas

exactement au type requis. Le nombre de câbles d'alimentation CA fournis correspond au

nombre de blocs d'alimentation du produit.

Notez que le commutateur CC de mise sous tension /hors tension du panneau avant n'éteint

pas l'alimentation CA du système. Pour mettre le système hors tension, vous devez

débrancher chaque câble d'alimentation de sa prise.

CONSIGNES DE SÉCURITÉ -Lorsque vous ouvrez le boîtier pour accéder à l’intérieur du

système, suivez les consignes suivantes:

1. Mettez hors tension tous les périphériques connectés au système.

2. Mettez le système hors tension en mettant l’interrupteur général en position OFF

(bouton-poussoir).

3. Débranchez tous les cordons d’alimentation c.a. du système et des prises murales.

4. Identifiez et débranchez tous les câbles reliés aux connecteurs d’E-S ou aux accès

derrière le système.

5. Pour prévenir les décharges électrostatiques lorsque vous touchez aux composants,

portez une bande antistatique pour poignet et reliez-la à la masse du système (toute

surface métallique non peinte du boîtier).

6. Ne faites pas fonctionner le système tandis que le boîtier est ouvert.

Une fois TOUTES les étapes précédentes accomplies, vous pouvez retirer les panneaux du

système. Procédez comme suit:

1. Si un cadenas a été installé sur à l’arrière du système, déverrouillez-le et retirez-le.

2. Retirez toutes les vis des panneaux et mettez-les dans un endroit sûr.

3. Retirez les panneaux.

Afin de permettre le refroidissement et l’aération du système, réinstallez toujours les

panneaux du boîtier avant de mettre le système sous tension. Le fonctionnement du

système en l’absence des panneaux risque d’endommager ses pièces. Pour installer les

panneaux, procédez comme suit:

1. Assurez-vous de ne pas avoir oublié d’outils ou de pièces démontées dans le système.

2. Assurez-vous que les câbles, les cartes d’extension et les autres composants sont bien

installés.

3. Revissez solidement les panneaux du boîtier avec les vis retirées plus tôt.

4. Remettez le cadenas en place et verrouillez-le afin de prévenir tout accès non autorisé à

l’intérieur du système.

5. Rebranchez tous les cordons d’alimentation c. a. et câbles externes au système.

Andere Handbücher für SC5300

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intel Server Handbücher

Intel

Intel R1000SPO series Konfigurationshandbuch

Intel

Intel ISP1100 - Server Platform - 0 MB RAM Bedienungsanleitung

Intel

Intel SR1530CL - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel R1000BB Family Bedienungsanleitung

Intel

Intel H2000WP Bedienungsanleitung

Intel

Intel M50CYP1UR Series Bedienungsanleitung

Intel

Intel TSRMT2 Bedienungsanleitung

Intel

Intel SBX82 - Server Compute Blade Bedienungsanleitung

Intel

Intel SR1670HV - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel R2000WF series Bedienungsanleitung

Intel

Intel TIGH2U - Carrier Grade Server Bedienungs- und Sicherheitshinweise

Intel

Intel P4308CP4MHEN Bedienungsanleitung

Intel

Intel SR2400SYS - Server Platform - 0 MB RAM Bedienungsanleitung

Intel

Intel S2600CW Bedienungsanleitung

Intel

Intel SR9000MK4U - Server System - 0 MB RAM Benutzerhandbuch

Intel

Intel S9200WK Series Bedienungsanleitung

Intel

Intel R2000BB series Bedienungsanleitung

Intel

Intel DCB Series Bedienungsanleitung

Intel

Intel SR2612UR - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel R1000GZ Bedienungsanleitung

Intel

Intel SR1695GPRX Bedienungsanleitung

Intel

Intel R1000GL Bedienungsanleitung

Intel

Intel M50CYP2UR Series Kurzanleitung zur Einrichtung

Intel

Intel S2600CP Family Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung