Intellinet 524377 (Annex b) Bedienungsanleitung

wireless N

ADsl2+

4-port

router

quick

iNstAll

guiDe

MODELS 524360 (ANNEX A)

& 524377 (ANNEX B)

INT-524360/524377-QIG-1208-01

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™Wireless N

ADSL2+ 4-Port Modem Router, Model 524360 (Annex A) or Model 524377

(Annex B).

An all-in-one modem, router, Wireless N access point, ﬁrewall and Fast Ethernet

4-port switch, it allows you to access the Internet and download music, play

interactive games online or surf the Web at double the speed previously available

through ADSL2.

This quick install guide presents the rudimentary steps required to set up and

operate this device. For more detailed instructions and speciﬁcations, refer to the

user manual 1) on the CD enclosed with this product; 2) on the Web site listed

below; or 3) in some cases, printed and enclosed with this product. Contact

your INTELLINET NETWORK SOLUTIONS dealer with comments or questions,

or visit www.intellinet-network.com for information on the latest software and

ﬁrmware updates, related products and additional contact information.

fcc regulAtory stAtemeNts

FCC Part 68

This equipment complies with Part 68 of FCC Rules. On the bottom of this device is

a label with the FCC registration number and ringer equivalence number (REN) for

this equipment. You must provide this information to the telephone company upon

request. The REN is useful to determine the quantity of devices you may connect to

the telephone line and still have all of those devices ring when your number is called.

In most areas, the total of the REN of all devices connected to one line should not

exceed ﬁve. To be certain of the number of devices you may connect to your line,

as determined by the REN, contact your local telephone company.

If the modem causes harm to the telephone network, the telephone company may

discontinue your service temporarily, notifying you in advance (if feasible) or as

soon as possible. You will be advised of your right to ﬁle a complaint with the FCC.

Also, the telephone company may make changes in its facilities, equipment,

operations or procedures that could affect the proper operation of your equipment.

If they do, you will be notiﬁed in advance to give you an opportunity to maintain

uninterrupted telephone service.

If you experience trouble with this device, contact your INTELLINET NETWORK

SOLUTIONS™dealer for repair/warranty information. The telephone company

may ask you to disconnect this equipment from the network until the problem has

been corrected or until you are sure that the equipment is not malfunctioning.

This equipment may not be used on coin service provided by the telephone

company. Connection to party lines is subject to state tariffs.

Installation

This device is equipped with a USOC RJ-11C connector.

FCC Part 15

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

This equipment must be installed and operated in accordance with provided

instructions, and a minimum of 20 cm spacing must be provided between computer-

mounted antenna and a person’s body (excluding extremities of hands, wrists and

feet) during wireless modes of operation.

This device complies with Part 15 of FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause

undesired operation. Any changes or modiﬁcations not expressly approved by the

party responsible for compliance could void the authority to operate equipment.

Federal Communications Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. In order to avoid the possibility of exceeding the

FCC radio frequency exposure limits, human proximity to the antenna shall not

be less than 20 cm (8 inches) during normal operation. The antenna(s) used

for this transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

R&TTE Compliance Statement

This equipment complies with all the requirements of Directive 1999/5/EC of the

European Parliament and the Council of March 9, 1999, on radio equipment and

telecommunications terminal equipment and the mutual recognition of their conformity

(R&TTE). The R&TTE Directive repeals and replaces Directive 98/13/EEC

(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) as

of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install

and use it. However, special attention must be paid to the dangers of electric

shock and static electricity when working with electrical equipment. All guidelines

of the FCC and of the computer manufacturer must therefore be followed at all

times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and ofﬁce use in Austria,

Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg,

the Netherlands, Portugal, Spain, Sweden and the United Kingdom.

The ETSI version of this device is also authorized for use in EFTA member states

Iceland, Liechtenstein, Norway and Switzerland.

EU Countries Not Intended for Use

None.

pAckAge coNteNts

• Wireless N ADSL2+ 4-Port Modem Router, Model 524360 (Annex A) or

Model 524377 (Annex B)

• Power adapter

• Ethernet Cat5 RJ-45 cable, 1.0 m (3 ft.)

• RJ-11 telephone cable, 1.8 m (6 ft.)

• Quick install guide

• Setup CD with user manual and setup wizard

hArDwAre

Front Panel

As listed below, the LED s indicate the current status of the router.

LED Mode Status

PWR (green) On Ready for operation.

WLAN (yellow) Off The wireless LAN is disabled.

Blinking Wireless trafﬁc is being transmitted/received.

WPS (Yellow) Off WPS function is disabled.

Blinking WPS function is enabled.

ADSL (green) On Successful connection to an ADSL DSLAN.

Blinking No connection.

LAN (LNK/ACT) On The LAN cable is connected to the router.

Ports 1-4 (green) Off No network connection.

Blinking Network trafﬁc is being transmitted/received.

Rear Panel

Antenna Connectors: The reverse SMA connectors allow easy connection to

external antennas.

Reset button: This can be used to reset the router or to restore the factory default

settings. Press the button (using a pencil tip can help) for less than ﬁve seconds

to re-boot the router and save any conﬁgurations that have been set up.

If problems persist after a simple re-boot — or if you’ve forgotten your password —

hold the button in for longer than ﬁve seconds to reset the router to its factory

default settings. NOTE: The factory default settings will replace any others that

have been conﬁgured.

Power outlet: The included 12 V DC power adapter is connected here.

WPS button: Wi-Fi Protected Setup (WPS) is the simplest way to build a connection

between wireless network clients and this router. Press this button and enable the

WPS function of the wireless clients; the router and clients will automatically

conﬁgure the security key and connect directly. NOTE: The router will wait for

WPS requests from wireless clients for 2 minutes after the WPS button is pressed.

LAN ports: The four local area network (LAN) ports are for connections to PCs,

LANs, printers, servers, hubs and so forth.

ADSL: The included RJ-11 phone line connects this to an ADSL/phone network.

Connections

1. From the ADSL port, connect the router to your ADSL network using the RJ-11

telephone cable provided.

2. From any of the LAN ports, connect the router to your PC, hub, switch or

other component using the Ethernet Cat5 RJ-45 cable provided.

3. Connect the router’s power outlet to a power source using the power adapter

provided. NOTE: Use only the power adapter included with this device.

4. Check that the green ADSL LED is on, indicating a successful connection. If

the ADSL LED is blinking — indicating that no connection has been made —

contact your Internet service provider.

coNfigurAtioN

ISP

This router provides a setup wizard used to conﬁgure the ADSL settings. This

wizard collects and enters ADSL settings from some Internet service providers

(ISPs) simply by selecting the ISP when prompted. If you cannot ﬁnd your

particular ISP listed in the wizard, refer to the Quick Start instructions in the Web

Management section of the user manual on the enclosed CD.

Before starting:

• Make sure the ADSL cable is connected to the router correctly. When the

ADSL cable is working normally, the ADSL LED will be on.

• Uninstall all dial-up programs previously installed for the USB modem or other

dial-up devices.

• It’s recommended that the router rst be congured with the Ethernet cable

connected prior to setting the wireless functions.

NOTE: This setup wizard can be run in Windows 2000, XP or Vista, though

the screen images shown may be representative of just one particular platform.

1. Insert the enclosed setup CD (featuring the setup wizard) into your CD-ROM

drive. The Autorun.exe program should be executed automatically. If not,

run Autorun.exe manually from the “Autorun” folder on the CD.

2. Click on “Setup Wizard”

when the initial menu

appears on screen. The

wizard will search for

the router. If the router

can’t be found, enter the

IP address and password

of the router, then click

“Next” to search again.

3. The wizard automatically

selects the country you’re

in (by identifying the

language of the computer’s

operating system), and

will then display the Select

ISP screen. Select the ISP.

If it’s not listed, click

“Other” to re- select the

country, or manually conﬁgure the ISP information (see Software/Setup Wizard /

Manually Set ISP in the user manual).

4. If prompted, enter the ISP-provided username and password, then click “Next.”

5. When the Settings

Overview screen displays,

click “Save,” which will

reboot the router.

After saving and rebooting,

the ISP settings are complete.

Click “Finish” to close the

setup wizard.

IP Address

To use the router to access the Internet, the PCs in the network must have an

Ethernet adapter installed and be connected to the router either directly or through

a hub or switch. The TCP/IP protocol of each PC has to be installed, and the IP

address of each PC has to be set in the same subnet as the router.

The router’s default IP address is 192.168.2.1; the subnet mask is 255.255.255.0.

PCs can be conﬁgured to obtain an IP address automatically through the DHCP

server of the router or a ﬁxed IP address in order to be in the same subnet as the

router. By default, the DHCP server of the router is enabled and will dispatch an

IP address to the PC from between 192.168.2.100 and 192.168.2.200. It is

strongly recommended that IP addresses be set/obtained automatically.

This section explains how to conﬁgure a PC so that it can obtain an IP address

automatically for Windows 2000, XP or Vista. For other operating systems

(Macintosh, Sun, etc.), follow the manual of that operating system.

Wi n d o W s Vi s t a :

1. Click “Start,” select “Settings,” then go to the control panel and double-click

“Network and Sharing Center” to display its window.

2. Click “Manage network connections,” right-click on the local Area Connection

icon and select Properties. The local Area Connection screen will display.

3. Check the list of network Components. You should see “Internet Protocol

Version 4 (TCP/IPv4)” on your list. Select it and click Properties.

4. On the Internet Protocol Version 4 (TCP/IPv4) Properties screen, select “Obtain

an IP address automatically” and “Obtain DNS server address automatically.”

5. Click “OK” to conﬁrm the setting. Your PC will obtain an IP address automatically

from the router’s DHCP server. NOTE: Make sure the router’s DHCP server is

the only one available on your LAN.

Wi n d o W s XP:

1. Click “Start,” open the control panel and then double-click “Network Connections.”

The Network Connections window will appear.

2. Right-click on the Local Area Connection icon and select Properties. The Local

Area Connection window will appear.

3. Check the list of Network Components. You should see “Internet Protocol

(TCP/IP)” on your list. Select it and click Properties.

4. In the Internet Protocol (TCP/IP) Properties window, select “Obtain an IP address

automatically” and “Obtain DNS server address automatically.”

5. Click “OK” to conﬁrm the setting. Your PC will now obtain an IP address

automatically from the router’s DHCP server. NOTE: Make sure the router’s

DHCP server is the only one available on your LAN.

Wi n d o W s 2000:

1. Click “Start” and select Settings, then click “Control Panel.”

2. Double-click on the Network and Dial-up Connection icon. In the Network

and Dial-up Connection window, double-click on the Local Area Connection

icon. The Llocal Area Connection window will appear.

3. In the Local Area Connection window, click “Properties.”

4. Check your list of Network Components. You should see “Internet Protocol

(TCP/IP)” on your list. Select it and click “Properties.”

5. In the Internet Protocol (TCP/IP) Properties window, select “Obtain an IP address

automatically” and “Oobtain dnS server address automatically.”

6. Click “OK” to conﬁrm the setting. Your PC will obtain an IP address automatically

from your router’s DHCP server. NOTE: Make sure the router’s DHCP server

is the only one available on your LAN.

After conﬁguring the PC(s) to obtain the IP address(es) automatically, the router’s

DHCP server will automatically give LAN clients an IP address. By default, the

server is enabled to do this. Once the PC has obtained an IP address from the

router, enter the default IP address 192.168.2.1 (the router’s IP address) into the

PC’s Web browser and press “Enter.”

The login screen will appear. Enter the username and password, then click “OK”

to log in. By default, the username is “admin” and the password is “1234.”

NOTE: For security reasons, it is recommended that the password be changed

as soon as possible.

Click “OK” to continue. The Home Page screen appears, displaying seven

instructional options: Quick Start, Interface Setup, Advanced Setup, Access

Management, Maintenance, Status and Help.

Quick Start

The Quick Start section is designed to get you using the router as quickly as

possible. Before conﬁguring the router, check with your ISP (Internet service

provider) as to what kind of service is provided (examples are shown in the

following table).

1. On the Home Page screen, click “Run Wizard” to start the conﬁguration. On

the subsequent screen, click “Next” to continue.

2. Set and conﬁrm the new

password; then click “Next”

to continue.

3. Select the time zone; then

click “Next” to continue.

PPPoE VPI/VCI, VC-based/LLC-based multiplexing, Username,

Password (and Service Name).

PPPoA VPI/VCI, VC-based/LLC-based multiplexing, Username,

Password.

RFC1483 Bridged VPI/VCI, VC-based/LLC-based multiplexing to use

Bridged Mode.

RFC1483 Routed VPI/VCI, VC-based/LLC-based multiplexing, IP Address,

Subnet Mask, Gateway Address and Domain Name

System (DNS) IP Address (a ﬁxed IP Address).

4. Select your Internet

connection type (as

directed by your ISP); then

click “Next” to continue.

5. Enter the data provided

by your ISP; then click

“Next” to continue.

6. Click “Next” to save the

settings and restart the

router.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intellinet Netzwerk-Router Handbücher

Intellinet

Intellinet Network Solutions 523462 Bedienungsanleitung

Intellinet

Intellinet 523523 Bedienungsanleitung

Intellinet

Intellinet 523776 Bedienungsanleitung

Intellinet

Intellinet 523646 Bedienungsanleitung

Intellinet

Intellinet 530347 Bedienungsanleitung

Intellinet

Intellinet 561457 Bedienungsanleitung

Intellinet

Intellinet 560559 Bedienungsanleitung

Intellinet

Intellinet 530347 Bedienungsanleitung

Intellinet

Intellinet 523608 Bedienungsanleitung

Intellinet

Intellinet 502023 Bedienungsanleitung

Intellinet

Intellinet 524988 Bedienungsanleitung

Intellinet

Intellinet 560931 Bedienungsanleitung

Intellinet

Intellinet 561051 Bedienungsanleitung

Intellinet

Intellinet 560535 Bedienungsanleitung

Intellinet

Intellinet 524636 Bedienungsanleitung

Intellinet

Intellinet 561051 Bedienungsanleitung

Intellinet

Intellinet 560405 Bedienungsanleitung

Intellinet

Intellinet 560559 Bedienungsanleitung

Intellinet

Intellinet 524803 Bedienungsanleitung

Intellinet

Intellinet 523813 Bedienungsanleitung

Intellinet

Intellinet 525831 Bedienungsanleitung

Intellinet

Intellinet 523493 Bedienungsanleitung

Intellinet

Intellinet 522595 Bedienungsanleitung

Intellinet

Intellinet 524988 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise