Interlogix 600-1046-95 Bedienungsanleitung

OEM Transceiver Module with Crystal

Transmitter Installation Instructions

Introduction

The OEM transceiver modules are compatible with Interlogix

wireless transmitters and receivers. The modules have an

onboard receiver and transmitter, microprocessor, and

connection for a daughter board. The microprocessor controls

the receiver and transmitter, providing antenna switching and

AGC functions. It also analyzes the data from the receiver,

validates incoming packets, and returns packets to the

controlling device when polled. A daughter board, which

communicates with the module via an 8-pin header, can be

added to implement a variety of functions.

Each module encapsulates the receiver and transmitter

functions and formats and presents a common interface to the

daughter board. Therefore, even though protocols vary among

the Interlogix radio frequencies used around the world, the

interface is the same to the daughter board.

Installation guidelines

Observe the following guidelines when installing the OEM

transceiver module:

• Allow at least 9 inches (22.9 cm) of clearance above the

enclosure for the antennas.

• Avoid mounting locations that expose the module to

moisture.

• Avoid areas with excessive metal or electrical wiring

including furnace and utility rooms. If unavoidable, mount

on or near metal with the antenna extending above the

metallic surfaces as shown in Figure 1.

Figure 1. Mounting on or near metal

METAL METAL

• While a transmitter may have an open-air range of 1000 ft.

(300 m) or more, the installation site can have a significant

effect on the transmitter range. Changing the sensor

location may help overcome adverse wireless conditions.

Installation

600-1029 enclosure

To mount the 600-1029 enclosure, follow the installation

instructions provided with the enclosure.

600-0131 daughter board

To attach the 600-0131 daughter board, follow the installation

instructions provided with the daughter board.

600-1046-95 OEM transceiver module

To mount the OEM transceiver module onto the back plate of

the 600-1029 enclosure, do the following:

1. Insert the antennas into the antenna shrouds (Figure 2).

Caution: You must be free of static electricity before handling

circuit boards. Wear a grounding strap or touch a bare metal

surface to discharge static electricity.

2. Gently slide the top of the circuit board under the two top

latches.

3. Snap the circuit board in at the bottom latch to secure it in

place as shown in Figure 2.

P/N 466-2236 • REV C • January 2011 1

Figure 2. Installing the circuit board

1 2 3 4 5 6 7 8

12345678

Antenna shrouds

600-1029 enclosure

Top latches

Bottom latch

2 mm power jack

Terminal block

OEM transceiver

LEDs

Daughter board

4. Connect DC power to the OEM transceiver module using

2 mm power jacks (center positive) or connect flyleads to

the terminal block as labeled on the board.

LED operation

Table 1 shows the LED indications for the OEM transceiver

module

Table 1: OEM transceiver module LED indications

Indication Green LED Red LED

Powered up On Off

Communication with daughter board On Flashing

Valid packet received One flash off Off or flashing

Troubleshooting

The following table gives troubleshooting suggestions for the

OEM transceiver module.

Table 2: OEM transceiver module troubleshooting

Problem Action

OEM transceiver module’s green

and red LEDs are off 1. Check that the transformer

is plugged in.

2. Check the transformer to

module wiring.

OEM receiver module’s green LED

is on and the red LED is off Check the daughter board

mounting.

Specifications

Model 600-1046-95

Frequency 319.5 MHz

Compatibility All 319.5 MHz sensors and 319.5 MHz

receivers

Current required (without daughter board)

Typical 45mA

Maximum 100mA

Voltage 8 to 15 VDC

Wireless range 1,000 feet (305 m) open air

Operating temperature 32 to 120°F (0 to 49°C)

Storage temperature -30 to 140°F (-34 to 60°C)

Maximum relative

humidity 90% noncondensing

Dimensions 3.2 x 4.6 x 0.6 inches (8.1 x 11.7 x 1.5 cm)

Features Antenna tamper, jam detect, wall tamper,

cover tamper

Optional items:

Enclosure 600-1029

USB daughter board 59-873

Repeater daughter

board 600-1031

Stand-off 40-262

Regulatory information

Manufacturer UTC Fire & Security Americas Corporation, Inc.

1275 Red Fox Rd., Arden Hills, MN 55112-6943,

USA

FCC compliance This device complies with FCC Rules Part 15.

Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference that

may be received, including interference that may

cause undesired operation.

Changes or modifications not expressly approved

by UTC Fire & Security can void the user’s

authority to operate the equipment.

FCC ID: B4Z-903-TCVR

IC: 867A-903-TCVR

California code This product cannot be sold in the state of

California if used to receive fire signals (per

section 208-g, Chapter 1.5 Construction Materials

and Equipment Listings, Title 19, California Code

of Regulations

(http://osfm.fire.ca.gov/pdf/fireengineering/bml/t-

19.pdf)).

Contact information

For contact information, see www.utcfireandsecurity.com or

www.interlogix.com.

For technical support, toll-free: 888.437.3287 in the US

including Alaska, Hawaii, Puerto Rico, and Canada. Outside

the tool-free area, contact your dealer.

2 OEM Transceiver Module with Crystal Transmitter Installation Instructions

Inhaltsverzeichnis

Andere Interlogix Steuereinheit Handbücher

Interlogix

Interlogix ITI SuperBus 2000 Bedienungsanleitung

Interlogix

Interlogix AdvisorOne AVO-ZW Montageanleitung

Interlogix

Interlogix ATS1201 8 Montageanleitung

Interlogix

Interlogix ATS7200N Montageanleitung

Interlogix

Interlogix UltraSync UM-C-H1 Montageanleitung

Interlogix

Interlogix Simon XT Bedienungsanleitung

Interlogix

Interlogix SuperBus 2000 Bedienungsanleitung

Interlogix

Interlogix RF-KF101-K4 Montageanleitung

Interlogix

Interlogix ATS7200E Montageanleitung

Interlogix

Interlogix TruPortal TP-ADD-2D-BRD Bedienungsanleitung

Interlogix

Interlogix DTIM Montageanleitung

Interlogix

Interlogix NX-595E Bedienungsanleitung

Interlogix

Interlogix NX-586E Bedienungsanleitung

Interlogix

Interlogix ATS7340 Montageanleitung

Interlogix

Interlogix DIGITAL INVERTER GENERATOR Montageanleitung

Interlogix

Interlogix SuperBus 2000 PIV Bedienungsanleitung

Interlogix

Interlogix ATS 500A Series Bedienungsanleitung

Interlogix

Interlogix ATS1831 Montageanleitung

Interlogix

Interlogix VT1101M-AC Montageanleitung

Interlogix

Interlogix TX-E121 Bedienungsanleitung

Interlogix

Interlogix VR1101M Montageanleitung

Interlogix

Interlogix UltraSync UM-Z8 Montageanleitung

Interlogix

Interlogix ATS1520 Montageanleitung

Interlogix

Interlogix UM-ZW Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung