Interlogix TruVision NVR 21 Bedienungsanleitung
TruVision NVR 21 Quick Start
Guide
P/N 1072630A-EN • REV 1.0 • ISS 02MAY13
Copyright © 2013 UTC Fire & Security Americas Corporation, Inc.
Interlogix is part of UTC Climate Controls & Security, a unit of United
Technologies Corporation. All rights reserved.
Trademarks and
patents
The TruVision and Interlogix names and logos are trademarks of United
Technologies.
Other trade names used in this document may be trademarks or registered
trademarks of the manufacturers or vendors of the respective products.
Contact
information
www.interlogix.com or www.utcfssecurityproducts.eu
NVR 21 Quick Start Guide 1 : EN
Figure 1: Back panel connections
1. Connect to one CCTV monitors (BNC-type
connectors).
2. Connect one audio input to RCA connectors.
3. Connect to a RS-232 device.
4. Connect to a network.
5. Connect to an optional eSATA device such as
SATA HDD, CD/DVD-RM.
6. Connect to a power cord.
7. Connect to speakers for audio output.
8. Connect to a VGA monitor.
9. Connect to a HDTV. The HDMI connection
supports both digital audio and video.
10. Connect to an optional USB device such as a
mouse, CD/DVD burner or HDD.
11. Terminate the line to the dome cameras using
this RS-485 switch. Default is Off.
12. Connect to a PTZ control.
13. Connect to a keyboard (KTD-405 shown)
14. Connect up to 16 alarm input cables to relay
outputs.
15. Connect up to four alarm relay outputs.
16. Connect to ground.
EN : 2 NVR 21 Quick Start Guide
Figure 2: Front panel controls
Item Name Description
1. Numeric buttons
Switch between different cameras in live, PTZ control or playback
modes.
2. USB Interfaces
Universal Serial Bus (USB) ports for additional devices such as a
USB mouse and USB Hard Disk Drive (HDD).
3. Status LEDs Power: Green indicates the NVR is working correctly. Red indicates
a fault.
Alarm: Red indicates that there is a sensor Alarm In or another alarm
such as motion or tampering.
Tx/Rx: Green indicates a normal network connection.
HDD: HDD indicator blinks red when data is being read from or
written to the HDD.
Ready: Green indicates the device is functioning properly.
Archive: Archive indicator blinks green when record files or pictures
are being exported to a USB or eSATA device.
4. Archive button Press once to enter quick archive mode. Press twice to start
archiving. Indicator blinks green when data is being written to backup
device.
5. Direction
The DIRECTION buttons are used to navigate between different
fields and items in menus.
In the Playback mode, the left and right buttons are used to speed up
and slow down recorded video. The up and down buttons are used to
jump recorded video forwards or backwards by 30 s.
In Pause mode, the left and right buttons are used to jump recorded
video forwards or backwards by one frame. The up and down buttons
are used to jump recorded video forwards or backwards by one
second.
In Live View mode, these buttons can be used to cycle through
channels.
In PTZ control mode, it can control the movement of the PTZ camera.
Enter button The ENTER button is used to confirm selection in any of the menu
modes.
In single-frame Playback mode, pressing the button will advance the
video by a single frame.
6. PTZ buttons Zoom: Use + and – for digital zoom.
Preset: Call up preprogrammed preset positions.
Tour: Call up preprogrammed shadow tours.
7. IR receiver Receiver for IR remote.
TVN 21 Quick Start Guide 3 : EN
Item Name Description
8. Menu and Search
buttons
Playback buttons
Menu: Enter/exit the main menu.
Search: Enter the advanced search menu.
: Reverse: In live view, play the earliest video file of the current
camera; In video playback mode, playback a camera in reverse
direction; In picture playback mode, view pictures in reverse direction.
Jump back to the oldest available video and starts the playback.
: Pause: Pause playback.
: Play: In live view, all-day playback of the current camera; In
video playback mode, playback a camera in the forward direction;
play a selected video and picture file; In picture playback mode, view
pictures in the forward direction.
Instantly playback the currently selected file. Default time is 1 minute.
Live: Switch to live view mode.
Replay: Replay the current file in playback Starts at the beginning of
the file.
9. Front panel lock
You can lock or unlock the front panel with a key.
10. Display buttons Display: Toggles through the various multiviews: full, quad, 1+5, 1+7,
9, and 16.
Sequence: Starts/stops sequencing in live view mode.
A: Selects the main monitor.
B: Selects the event monitor (in live view).
F1: In all-day playback, click to start and stop video clipping.
F2: In live view mode, click to display/hide the time bar.
In all-day playback, click to hide/display the playback control toolbar.
Package contents
The TruVision NVR 21 (model TVN 21) is
shipped with the following items:
• IR (infrared) remote control
• Two AAA batteries for the remote
control
• AC power cords (US, Europe, UK)
• USB mouse
• NVR
• CD with software and manuals
• TruVision NVR 21 Quick Start Guide
• TruVision NVR 21 User Manual (on CD)
Installation environment
Refer to the user manual for detailed
information, but observe these important
requirements:
• Place the unit in a secure location.
• Ensure that the unit is in a well-
ventilated area.
• Do not expose the unit to rain or
moisture.
Quick install
Recommended steps for setting up the
NVR:
1. Connect all the devices required to the
back panel of the NVR. See Figure 1 on
page 1.
Basic connections:
Connect monitor A to the BNC, VGA or
HDMI output. Connect the mouse to the
USB port in the front panel.
Optional connections:
All the other connections shown are
optional and depend upon installation
requirements.
2. Connect the power cord to the unit and
turn on the power.
EN : 4 TVN 21 Quick Start Guide
3. Set up the unit with the required
settings using the setup wizard.
First-time use
The NVR has an express installation wizard
that lets you easily configure basic NVR
settings when first used. It configures all
cameras simultaneously. The configuration
can then be customized as required.
By default, the setup wizard will start once
the NVR has loaded. The wizard walks you
through some of the more important
settings of your NVR. Select the preferred
language for the system and then enter the
administrator password. The default admin
password is 1234. It is strongly
recommended that this password is
changed.
The wizard will then guide you through the
menus to set the time and date, network
configuration, HDD management, and
recording configuration.
When all the required changes have been
entered, click Finish to exit the wizard. The
NVR is now ready to use. Recording starts
automatically.
Operating the TVN 21
There are several ways to control the unit:
• Front panel
• IR remote control
• Mouse
• Web browser
Front panel
The buttons on the front panel control most
functions. See Figure 2 on page 2 for the
locations of the controls.
IR remote control
The IR remote control buttons are similar to
those on the front panel. Place the two AAA
batteries in the remote control.
To connect the remote control to the
NVR:
1. Press Menu on the front panel or right-
click the mouse and select Menu. The
main menu screen appears.
2. Select Network > General.
3. Check and remember NVR device
address value. The default value is 255.
The device address is valid for all IR
controls.
4. On the remote control, press the
Device button.
5. Enter the device address value. It must
be the same as that on the TVN 21.
6. Press ENTER on the remote or front
panel.
USB mouse
The USB mouse provided with the TVN 21
operates all the functions of the NVR, unlike
the front panel, which has limited
functionality. The mouse lets you navigate
and make changes to settings in the user
interface.
Connect the mouse to the NVR by plugging
the mouse USB connector into the USB
port on the front panel. The mouse is
immediately operational and the pointer
should appear.
Web browser control
The TVN 21 Web browser lets you view,
record, and play back videos as well as
manage all aspects of the NVR from any
PC with Internet access. The browser’s
easy-to-use controls give you quick access
to all NVR functions. See Figure 3 on page
5.
To access the unit, open a web browser
and enter the IP address assigned to the
NVR as a Web address. In the login screen,
enter the default user ID and password:
• User ID: admin
• Password: 1234
The default values for TVN 21 network
settings are:
TVN 21 Quick Start Guide 5 : EN
• DHCP: Enabled by default.
• IP address - 192.168.1.82
• Subnet mask - 255.255.255.0
• Gateway address - 192.168.1.1
• Ports:
When using the browser:
RTSP port: 554
HTTP port: 80
When using TruNav:
RTSP port: 554
Server/Client software port : 8000
Figure 3: Web browser interface
Live view mode
Live mode is the normal operating mode of
the unit where you watch live pictures from
the cameras.
Regularly used functions in live view can be
quickly accessed by clicking the right-button
of the mouse on the camera image. The
shortcut pop-up toolbar appears. See
Figure 4 below for a description of the
functions available.
Figure 4: The mouse menu for the main
monitor
The list of commands available depends on
which monitor is active; main or spot
(monitor B). See Table 1 below.
Table 1: Mouse menu for monitor A
(main monitor)
Item Name Description
1. Menu Enter the Main menu.
This option is not available
from monitor B.
2. Single
camera
Switch to a full-screen view
for the selected camera from
the dropdown list.
3. Multi
camera
Switch between the different
multiview options from the
dropdown list.
4. Previous
screen
Displays the previous
camera.
5. Next
screen
Displays the next camera.
6. Start auto-
switch
Turn on sequence mode.
The screen automatically
sequences between
cameras.
Go to Menu > Display Mode
Settings > Layout > Dwell
Time to set up.
7. All-day
playback
Playback the recorded video
of the selected day from the
selected camera. The current
day is selected by default.
8. Monitor B Switch between monitors A
(main) and B (spot).
9. Advanced
search
Enter the advanced video
search menu.
EN : 6 TVN 21 Quick Start Guide
Item Name Description
10. Close
timebar
Open/close the time bar.
Configuring the TVN 21
The NVR has an icon-driven menu structure
that allows you to configure the unit’s
parameters. Each command icon displays a
screen that lets you edit a group of settings.
Most menus are available only to system
administrators.
Refer to the NVR user manual for detailed
information on configuring the unit.
To access the main menu from live view:
Press the Menu button on the remote
control or front panel
- Or -
Right-click the mouse, and select Menu
from the pop-up menu.
The main menu screen appears. Move the
mouse over a command icon in the menu
toolbar and click to select it.
Description of the command icons in the
menu toolbar:
Configures camera settings.
Configures display settings.
Configures recording settings.
Configures standard network
settings.
Configures alarm settings.
Configures PTZ settings.
Configures user settings.
Configures system settings.
Provides reference information
to the various toolbars and
menus within the interface.
Provides access to logout,
reboot and shutdown options.
Specifications
Power supply 100 to 240 VAC,
6.3 A, 50 to 60 Hz
Power
consumption
(without HDD)
<= 45 W
Operating
temperature
-10 to +55 ºC
(50 to 131 °F)
Relative humidity 10 to 90%
Dimensions
(W x D x H)
442 × 371 × 74 mm
(17.4 × 14.61 × 2.91 in.)
Weight ≤8 kg (≤17.6 lb.)
(without HDD or DVD-R/W)
Contact information
For contact information, see
www.interlogix.com, or
www.utcfssecurityproducts.eu
Andere Handbücher für TruVision NVR 21
7
Inhaltsverzeichnis
Beliebte Netzwerk-Videorekorder Handbücher anderer Marken
Planet
Planet NVR-1615 Bedienungsanleitung
Q-See
Q-See QT454 Bedienungsanleitung
HIK VISION
HIK VISION DS-9600NI-ST Series Bedienungsanleitung
HIK VISION
HIK VISION DS-96128NI-I16 Bedienungsanleitung
Security Camera King
Security Camera King NVR-EL-16 Bedienungsanleitung
Honeywell
Honeywell HEN04101(X) Bedienungsanleitung