Intermec 5023 Bedienungsanleitung
5023 Data
Collection PC™
Getting Started Guide
P/N 070505-001
32
Intermec Technologies Corporation
6001 36th Avenue West
P.O. Box 4280
Everett, WA 98203-9280
U.S. service and technical support: 1-800-755-5505
U.S. media supplies ordering information: 1-800-227-9947
Canadian service and technical support: 1-800-688-7043
Canadian media supplies ordering information: 1-800-268-6936
Outside U.S. and Canada: Contact your local Intermec service supplier.
The information contained herein is proprietary and is provided solely for
the purpose of allowing customers to operate and/or service Intermec
manufactured equipment and is not to be released, reproduced, or used
for any other purpose without written permission of Intermec.
Information and specifications in this manual are subject to change
without notice.
2000 by Intermec Technologies Corporation
All Rights Reserved
The word Intermec, the Intermec logo, JANUS, IRL, Trakker, Antares,
Universal Access Point, UAP, TE2000, Data Collection Browser,
dcBrowser, Data Collection PC, Adara, Duratherm, EZBuilder, Precision
Print, PrintSet, Virtual Wedge, and CrossBar are either trademarks or
registered trademarks of Intermec Technologies Corporation.
Throughout this manual, trademarked names may be used. Rather than put
a trademark (or ) symbol in every occurrence of a trademarked name,
we state that we are using the names only in an editorial fashion, and to
the benefit of the trademark owner, with no intention of infringement.
ContentsContents
ContentsContents
Contents
Introducing the 5023 Data Collection PC 5
Equipment You Need to Get Started 5
Getting the 5023 Up and Running 5
Unpacking the 5023 6
Charging and Installing the Main Battery Pack 6
About the Bridge Battery 8
Turning On the 5023 and Verifying Operation 9
Specifications 10
Where to Find Other Information 11
54
Introducing the 5023 Data Collection PC
The 5023 Data Collection PC™ is a portable hand-held computer that
comes ready to connect to your RF network. With an IEEE 802.11B High
Rate (HR) radio, Smart Card reader, and handle with scanner trigger, the
5023 makes data collection easy and is engineered to take full advantage
of its Microsoft Windows CE operating system.
5023
Equipment You Need to Get Started
To use the 5023 Data Collection PC, you need this equipment:
•Lithium-ion main battery pack (Part No. 068537, sold separately)
•Z2400 battery charger
•(Optional) L5020 Serial Communications Adapter and power supply
(Part No. 065236) or D5020 Communications Dock
Getting the 5023 Up and Running
Follow these steps to start using your new 5023:
Unpack the 5023 and documentation.
Charge and install a main battery pack.
Turn on the 5023 and verify correct operation.
These steps are described in detail in the next sections.
1
2
3
76
You can also use the D5020 Communications Dock or the L5020 Serial
Communications Adapter with power supply to trickle-charge the main
battery pack. For help, see the D5020 Communications Dock Getting
Started Guide (Part No. 068976) or the L5020 Serial Communications
Adapter Quick Reference Guide (Part No. 068978).
Replace the main battery pack with Part No. 068537 only. The use of any
other battery pack may present a risk of fire or explosion. Contact your
local Intermec sales representative for replacement main battery packs.
DISPOSE OF USED MAIN BATTERY PACKS PROMPTLY. KEEP
AWAY FROM CHILDREN.
To install the main battery pack
1. Open the battery door by pushing down on the latch and sliding it
toward the top end of the 5023. Lift up the edge of the battery door
and remove it.
Battery
door
To p
Latch
5020GSG003.eps
2. Place the main battery pack into the battery compartment with the
contacts pointed toward the bottom end of the 5023.
3. Push the main battery pack down until it locks into the connectors on
the bottom of the battery compartment.
5020GSG004.eps
Unpacking the 5023
When you remove the 5023 from its box, save the box and shipping
material in case you need to ship or store the 5023. Check the contents of
the box against the invoice for completeness, and contact your local
Intermec service representative if there is a problem.
5023G003.eps
5023
5020
5023 Data
Collection PC
Information
packet
GettingStartedGuide
LocalAreaSystemsDivision
5023 Data
Collection PC
5020
These items should be in the information packet:
•Getting Started Guide (this document)
•Authorized Service Location sheet
•Safety supplement
•Microsoft software agreement
•Laser warning label set
Charging and Installing the Main Battery Pack
The main power source for the 5023 is a 1500 mAh lithium-ion battery
pack. The 5023 will not operate without a main battery pack even when it
is connected to an AC power source using a D5020 or an L5020. Before
you can use the 5023, you must fully charge the main battery pack.
To charge the main battery pack
•Place the main battery pack in an empty slot in the Z2400 battery
charger. The main battery pack is fully charged in about 4 hours. For
help, see the documentation that came with your battery charger.
1
2
98
Turning On the 5023 and Verifying Operation
This section explains how to turn on the 5023 and scan a test bar code to
verify operation.
To turn on the 5023 and scan a bar code
1. Press the yellow f key in the lower right corner of the keypad.
On/Off key
502G013.eps
The 5023 desktop appears.
2. Press C3to open the Start menu.
4. Insert the top edge of the battery door into the top of the battery
compartment. Push the door down to close it over the compartment.
5. Push the battery door latch down and slide it toward the bottom end
of the 5023 to lock the door in place.
The 5023 initializes after you install a charged main battery pack. The
green LED above the screen flashes until initialization is complete.
5023G010.eps
5023
LED
About the Bridge Battery
The 5023 comes with a rechargeable bridge battery that maintains the
contents of RAM while the main battery pack is being replaced. For more
information about the bridge battery, see the 5023 Data Collection PC
User’s Manual (Part No. 070698).
IMPORTANT: The 5023 is shipped with a discharged bridge battery. Do
not install applications on the 5023 until the bridge battery is fully
charged.
•The bridge battery recharges from the main battery pack or recharges
from the AC power source.Wait until the bridge battery is fully
charged before proceeding to the next section. It takes 72 hours at
room temperature to charge a discharged bridge battery.
Note: You should always keep a charged main battery pack
installed in the 5023 to maximize the life of the bridge battery.
3
1110
Power Specifications
Operating: Rechargeable lithium-ion 1500 mAh battery pack
Memory Backup: Rechargeable lithium manganese dioxide 90 mAh
bridge battery
Electrical Specifications
Electrical Rating: N7,4 to 12V; 750mA peak
Temperature and Environmental Specifications
Operating Temperature: -20°C to +50°C-4°F to +122°F
Storage Temperature
less than 2 weeks: -20°C to +60°C-4°F to +140°F
longer than 2 weeks: -20°C to +45°C-4°F to +113°F
Relative Humidity: 0 to 95% non-condensing
Accessories
•Z2400 Battery Charger
•D5020 Communications Dock
•L5020 Serial Communications Adapter
For more information, see your Intermec sales representative.
Where to Find Other Information
For more information on using the 5023, please see
•the 5023 Data Collection PC User’s Manual (Part No. 070698).
•the Intermec Web site at www.intermec.com.
3. Press ]to select Programs, then press }to select DCPC Demo, and
press e(Enter). The DCPC Demo screen appears.
4. Hold the 5023 at a slight angle a few inches from the Test Bar Code,
with the laser scan window pointing toward the bar code.
Scan the Test Bar Code by pulling the trigger on the handle, or by
pushing the Scan button on the keypad. Direct the beam so that it
falls across all bars in the bar code label.
Test Bar Code
*12345*
*12345*
After successfully reading the label, the 5023 emits a high beep and
the green LED lights for about a second.
5. To check that the 5023 decoded the bar code correctly, make sure
12345 appears in the Part Number field.
6. Press rto select Exit and press eto exit DCPC Demo.
The 5023 is now ready to configure and connect to your RF network. You
can use the Fast Config application to quickly set up general network
parameters. For more information, see the 5023 Data Collection PC
User’s Manual.
Specifications
Physical Dimensions
Width: 10.2 cm (4.0 in) at the screen
7.0 cm (2.75 in) at the handle
Length: 22.9 cm (9.0 in)
Depth: 7.6 cm (3.0 in) at the scan module
9.4 cm (7.63 in) at the handle
Weight: 952 g (29.8 oz)
12
Part No. 070505-001
*070505-001*
*070505-001*
Andere Handbücher für 5023
1
Andere Intermec PDA Handbücher
Intermec
Intermec CN3E Series Leitfaden
Intermec
Intermec CN70e RFID Bedienungsanleitung
Intermec
Intermec CK30 Bedienungsanleitung
Intermec
Intermec JANUS JG2050 Bedienungsanleitung
Intermec
Intermec PEN*KEY 6100 Bedienungsanleitung
Intermec
Intermec Trakker Antares 2425 Bedienungsanleitung
Intermec
Intermec CK3R Bedienungsanleitung
Intermec
Intermec CV30 Bedienungsanleitung
Intermec
Intermec CN51 Bedienungsanleitung
Intermec
Intermec CN51 Bedienungsanleitung
Intermec
Intermec NORAND 6642 Bedienungsanleitung
Intermec
Intermec Trakker Antares 2425 Handbuch
Intermec
Intermec CV60 Bedienungsanleitung
Intermec
Intermec Trakker Antares 2415 Handbuch
Intermec
Intermec 6600 Bedienungsanleitung
Intermec
Intermec Trakker Antares 2475 Bedienungsanleitung
Intermec
Intermec 6210 Bedienungsanleitung
Intermec
Intermec CK3X Bedienungsanleitung
Intermec
Intermec M90 Series Bedienungsanleitung
Intermec
Intermec 5055 Bedienungsanleitung
