Intermec EasyCoder 501 SA Bedienungsanleitung

EasyCoder 501/601

Sensor Kit

P/N 1-960411-02

Edition 3

September 1998

Installation Instructions

EasyCoder 501/601 – Installation Instructions

SENSOR KIT

Intermecoffersakitcontainingtwosensors,thatdetecttherotation

of the paper supply spool and the ribbon unwind shaft and update

two counters, one for each sensor. By means of custom-made

applicationprograms,thecounterscanbereadandusedforindicate

paper-lowandribbon-low conditions (asopposedto out-of-paper-

out and out-of-ribbon conditions, which are supported by the

standard error handling). See SYSVAR system array in Intermec

Fingerprint 6.13 Reference Manual1.

The Sensor Kit is available for the following printer models:

Model Ribbon Low Sensor Paper Low Sensor

EasyCoder 501 E yes yes

EasyCoder 501 SA yes yes

EasyCoder 601 S yes no

EasyCoder 601 E yes yes

Thesensorkitconsistsoftwophoto-electric sensors and two #T10

Torx screws.

The sensors require no regular cleaning. However, should any

malfunctionbedetected,youmaytrytoblowthesensorclearfrom

dust or paper residue before replacing it.

The sensitivity of these sensors cannot be adjusted.

Introduction

Ribbon Low Sensor Paper Low Sensor

The illustration shows the sensor kit fitted on an EasyCoder 501 E

printer.

1/. The system variable SYSVAR reads

the counters as follows:

SYSVAR (12) reads the paper counter

SYSVAR(13)readstheribboncounter

EasyCoder 501/601

Sensor Kit

Installation Instructions

Edition 3, September 1998

Part No. 1-960411-02

EasyCoder 501/601 – Installation Instructions

SENSOR KIT, cont'd.

Installation

Ribbon Low Sensor

• Open the right hand door.

• Turn off the power and remove the left-hand cover.

• Fromthe papercompartmentside,inserttheconnectorandcable

through the square hole in the centre-line wall.

• Insertthesensorunderthecodediskoftheribbonunwindunitso

the disc will run in the U-shaped slot between the receiver and

transmitter.

• Attach the sensor to the centre-line wall by means of one #T10

Torx screw. Check that the code disc can rotate freely.

• ConnectthecabletoconnectorP-605atthetopoftheCPUboard

(marked ➀).

• Continue by fitting the paper low sensor.

Paper Low Sensor

• Remove the three #T20 Torx screws holding the large crescent-

shapedguideplatethatsurroundsthepapersupply unit. Remove

the guide plate.

• Fit the sensor under the code disc of the upper supply unit using

the same method as with the ribbon low sensor.

• ConnectthecabletoconnectorP-602atthetopoftheCPUboard

(marked ➁).

• Fit back the guide plate and the left-hand cover.

Note!

The ribbon unwind unit and the paper

supply unit are shown dismounted in

the drawing only to improve visibility.

In reality, the only part that requires

dismounting is the guide plate.

Guide Plate

(remove)

Ribbon Unwind Unit

(do not remove) Paper Supply Unit

(do not remove)

Sensor

#T10 Torx screw

#T20 Torx screw (3x)

Sensor

#T10 Torx screw

Andere Handbücher für EasyCoder 501 SA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intermec Druckerzubehör Handbücher

Intermec

Intermec PB50 Bedienungsanleitung

Intermec

Intermec EasyCoder 501XP Bedienungsanleitung

Intermec

Intermec 869 RFID Reader Betriebsanleitung

Intermec

Intermec PC43d Bedienungsanleitung

Intermec

Intermec 3240 Bedienungsanleitung

Intermec

Intermec EasyCoder 601XP Bedienungsanleitung

Intermec

Intermec EasyCoder PD4 Bedienungsanleitung

Intermec

Intermec EasyCoder PF4ci Bedienungsanleitung

Intermec

Intermec PB42 Handbuch

Intermec

Intermec 3600 Bedienungsanleitung

Intermec

Intermec EasyCoder 201II Betriebsanleitung

Intermec

Intermec PB2 Series Handbuch

Intermec

Intermec PM4I Bedienungsanleitung

Intermec

Intermec 4630 Bedienungsanleitung

Intermec

Intermec EasyCoder 601XP Bedienungsanleitung

Intermec

Intermec EasyCoder PC4 Bedienungsanleitung

Intermec

Intermec PA30 Bedienungsanleitung

Intermec

Intermec EasyCoder F2 Bedienungsanleitung

Intermec

Intermec ESim v4.20 Bedienungsanleitung

Intermec

Intermec EasyCoder PF2i Bedienungsanleitung

Intermec

Intermec EasyCoder F4 Bedienungsanleitung

Intermec

Intermec PB50 Bedienungsanleitung

Intermec

Intermec EasyCoder 101 Handbuch

Intermec

Intermec 074788 Series Bedienungsanleitung

Beliebte Druckerzubehör Handbücher anderer Marken

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

REA

REA JET HR pro 2K Bedienungsanleitung

HP Laserjet,Color Laserjet 4si Bedienungsanleitung

oliser

oliser MS 45 Bedienungsanleitung

Roland

Roland DU2-64 Anleitungen und Rezepte

Xerox

Xerox EFI EXP6000 Bedienungsanleitung

Canon

Canon Finisher-T1 Bedienungsanleitung

Sharp

Sharp FO-1MK Bedienungsanleitung

Labelmate

Labelmate PM-300 Bedienungsanleitung

Epson

Epson T6248 Betriebsanleitung

Epson

Epson OT-BZ20 Bedienungsanleitung

Canon

Canon TonerRobot EP-27 Bedienungsanleitung

Ricoh

Ricoh LCIT RT5100 Kurzanleitung

GBC

GBC 16 Series Bedienungsanleitung

Canon

Canon INNER 2-WAY TRAY-E1 Bedienungs- und Wartungshandbuch

Develop

Develop SD-509 Bedienungsanleitung

Kyocera

Kyocera KM-6230 Handbuch

Triumph Adler

Triumph Adler DF-710 Handbuch