Intermec EasyCoder PF2i Bedienungsanleitung

Installation

Instructions

EasyLAN Wireless

Interface Kit

(for EasyCoder PF2i,

PF4i, PF4ci, PM4i, PX4i,

and PX6i Printers)

Intermec Technologies Corporation

Corporate Headquarters

6001 36th Ave. W.

Everett, WA 98203

U.S.A.

www.intermec.com

e information contained herein is proprietary and is provided solely for the

purpose of allowing customers to operate and service Intermec-manufactured

equipment and is not to be released, reproduced, or used for any other purpose

without written permission of Intermec.

Information and speciﬁcations contained in this document are subject to

change without prior notice and do not represent a commitment on the part of

Intermec Technologies Corporation.

e word Intermec, the Intermec logo, Norand, ArciTech, CrossBar, Data

Collection Browser, dcBrowser, Duratherm, EasyCoder, EasyLAN, Enterprise

Wireless LAN, EZBuilder, Fingerprint, i-gistics, INCA (under license), Inter-

Driver, Intermec Printer Network Manager, IRL, JANUS, LabelShop, Mobile

Framework, MobileLAN, Nor*Ware, Pen*Key, Precision Print, PrintSet, Route-

Power, TE 2000, Trakker Antares, UAP, Universal Access Point, and Virtual

Wedge are either trademarks or registered trademarks of Intermec Technologies

Corporation.

roughout this manual, trademarked names may be used. Rather than put a

trademark (™ or ®) symbol in every occurrence of a trademarked name, we state

that we are using the names only in an editorial fashion, and to the beneﬁt of

the trademark owner, with no intention of infringement.

ere are U.S. and foreign patents pending.

Torx is a registered trademark of Camcar Division of Textron Inc.

is product includes software developed by the OpenSSL Project for use in the

OpenSSL Toolkit (http://www.openssl.org/).

is product includes cryptographic software written by Eric Young

([email protected]).

EasyLAN Wireless Interface Kit Installation Instructions iii

Contents

1 Introduction

About ese Instructions ...............................................................2

Printer Firmware............................................................................2

Installation Kit...............................................................................2

Important 802MIG2 Information .................................................3

2 Physical Installation

Step-by-Step Instructions .............................................................14

3 EasyLAN Network Setup

EasyLAN Network Setup.............................................................24

Establishing Serial Communication .............................................24

Installing EasyLAN Network Setup..............................................25

Starting EasyLAN Network Setup................................................25

User and Password .......................................................................26

4 Setup in Fingerprint

Setting Up Wireless Communication...........................................28

Reading Other Wireless Connection Variables .............................37

Reading Wireless Connection Setup.............................................40

Setting Up Network Parameters ...................................................40

Finishing the Setup ......................................................................42

5 Setup in IPL

Setting Up Wireless Communication...........................................44

Reading Other Wireless Connection Variables .............................52

Finishing the Wireless Setup ........................................................54

Setting Up Network Parameters ...................................................55

6 Accessing the Printer’s Home Page

Using the Web Browser................................................................62

iv EasyLAN Wireless Interface Kit Installation Instructions

Contents

EasyLAN Wireless Interface Kit Installation Instructions 1

is chapter describes the EasyLAN Wireless interface

kit for EasyCoder PF2/4i-, PM4i-, and PX4/6i-series

printers. It also contains important information

regarding radio communication.

1 Introduction

2 EasyLAN Wireless Interface Kit Installation Instructions

Chapter 1 — Introduction

About These Instructions

ese instructions describe how to install an EasyLAN Wireless network

interface in an EasyCoder PF2i, PF4i, PF4i Compact Industrial, PM4i,

PX4i, or PX6i printer and how to connect it to a LAN, WAN, Intranet,

or Internet network via a wireless connection.

e installation instructions describe how to physically install the inter-

face board in a printer and how to set up the IP address, subnet mask,

default router, and name server. e instructions end when you have

the printer’s home page up and running. From there, please refer to the

Intermec EasyLAN User’s Guide on the included CD-ROM.

is interface kit must only be physically installed by an

authorized service technician. e device is country/region

speciﬁc and must be ordered for the correct country/region.

Use of this device in other region than shown on the device

home page/test label may violate applicable law.

Printer Firmware

For full functionality, your printer should either be ﬁtted with Intermec

Fingerprint v8.40 (or later) or IPL v2.40 (or later). In Intermec Finger-

print, the network port is addressed as device "net1:" (communication

channel #5).

Installation Kit

e EasyLAN Interface Kit contains:

• One EasyLAN adapter board complete with radio module ﬁtted

• Rear plate (for EasyCoder PF2/4i-series printers only)

• RJ-45 plug (for EasyCoder PM4i and PX4/6i only)

• One light guide

• One hexagonal threaded spacer

• One antenna extension cable

• One antenna

• One cable clip

• One cable tie

• One CD-ROM with software and manuals

• is Installation Instruction booklet

e only tools required for the installation are #T10 and #T20 Torx

EasyLAN Wireless Interface Kit Installation Instructions 3

Chapter 1 — Introduction

Important 802MIG2 Information

For Users in the United States and Canada

is device complies with Part 15 of the FCC Rules and with RSS-210

of Industry Canada. Operation is subject to the following two condi-

tions: (1) is device may not cause harmful interference, and (2) is

device must accept any interference received, including interference that

can cause undesired operation.

Federal Communications Commission Compliance

is equipment is intended for operation in a commercial environment,

in compliance with the requirements for a Class B digital device, pursu-

ant to Part 15 of the FCC Rules, and it must not be used in a residential

environment. It generates, uses, and can radiate radio frequency energy.

If not installed and used in accordance with the instruction manual,

it may cause interference to radio communications. If this equipment

causes interference, the user will be required to correct the interference at

the user’s own expense.

Operation Warning: e user shall stay at least 20 cm (8

in) away from the antenna of this device, when the device

is in use in access points and other hosts, where higher gain

antennas may be used.

Installation Warning: To comply with the FCC’s RF expo-

sure requirements and minimize health hazards:

Host devices with higher gain antennas such as access

points must be installed in such a way that the user will

be at least 20 cm (8 in) away from the antenna, when the

device is in use.

e installers should not forget that the burden of main-

taining this distance is on the installer and not the user. the

antennas should be installed in a manner that will comply

with this requirement.

Changes or modiﬁcations not expressly approved by

Intermec could void the user’s authority to operate this

equipment.

4 EasyLAN Wireless Interface Kit Installation Instructions

Chapter 1 — Introduction

Note: To maintain compliance with FCC Rules, the input/

output (I/O) cables that interconnect between the device and

any peripheral must be as speciﬁed by Intermec.

Industry Canada Compliance

is Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

is device requires a radio license, unless it is used totally inside a build-

ing. (e user must obtain this license.)

Cet appareil numérique de la classe B respecte toutes les exigences du

Règlement sur le matériel brouilleur du Canada.

Cet appareil exige une license radio à moins d’être entièrement installé

dans un bâtiment. (L’utilisateur doit obtenir cette license.)

EasyLAN Wireless Interface Kit Installation Instructions 5

Chapter 1 — Introduction

For Users Outside of the United States and Canada

e Intermec product you purchased contains a Mode 802MIG2 trans-

ceiver module. is module transmits and receives data using a 2.4 GHz

Direct Sequence Spread Spectrum system.

Please check the Intermec web site for additional documentation at

www.intermec.com.

Hereby, Intermec Technologies Corporation declares that this Model

802MIG2 is in compliance with the essential requirements and other

relevant provisions of R&TTE Directive (1995/5/EC). is product has

been assessed to the following standards:

• ETSI EN 300 328-2 v1.2.1 (2001-12)

• ETSI EN 301 489-17 v1.1.1 (2001-09)

• EN 60950:1992 (incl. Amdt. 1-4,11)

e original Declaration of Conformity is available on the Intermec

Technologies Corporation web site at www.intermec.com.

is product transmits electromagnetic waves at 2.4 GHz frequency

range. It has been tested and found compliant with U.S. (OET Guide

65) and Canadian (RSS 102) RF exposure regulations. ere are no

regulations covering this product type in the European Union at this

time.

e transmitter module’s output power is 11.6 mW. e product using

this module are intended for business and industrial environments. ey

should not be used in residential environments and by children.

is product is marked with this logo and uses

radio frequency bands that are not harmonized

throughout the European Union.

6 EasyLAN Wireless Interface Kit Installation Instructions

Chapter 1 — Introduction

e following table indicates the areas of intended use of the equipment

and any known restrictions.

Country of

Intended Use

Yes No License

Required

Restric-

tions

Details

Austria X

Belgium X

Denmark X

Finland X

France X X 2454 to 2483 MHz

bands must not be

used outdoors on this

device.

Germany X

Greece X

Ireland X

Italy X

Luxembourg X

e Netherlands X

Portugal X

Slovenia X

Spain X

Sweden X

United Kingdom X

Other non-EU:

Iceland X

Liechtenstein X

Norway X

Switzerland X

Additional EMI/RFI Compliance

is device meets the Class B limit requirements of CISPR 22.

Andere Handbücher für EasyCoder PF2i

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intermec Drucker Handbücher

Intermec

Intermec PB40 Bedienungsanleitung

Intermec

Intermec EasyCoder F4 Bedienungsanleitung

Intermec

Intermec 3240 Bedienungsanleitung

Intermec

Intermec 3240 Bedienungsanleitung

Intermec

Intermec ColorCoder V4 Bedienungsanleitung

Intermec

Intermec EasyCoder 201II Handbuch

Intermec

Intermec EasyCoder PD41 Bedienungsanleitung

Intermec

Intermec PM43 Bedienungsanleitung

Intermec

Intermec PC23d Bedienungsanleitung

Intermec

Intermec PM23c Bedienungsanleitung

Intermec

Intermec EasyCoder 601XP Bedienungsanleitung

Intermec

Intermec PB3 Series Bedienungsanleitung

Intermec

Intermec PB42 Bedienungsanleitung

Intermec

Intermec PM4I Bedienungsanleitung

Intermec

Intermec EasyCoder 4100 Bedienungsanleitung

Intermec

Intermec 4820F Bedienungsanleitung

Intermec

Intermec 3400 Bedienungsanleitung

Intermec

Intermec EasyCoder 401 Bedienungsanleitung

Intermec

Intermec EasyCoder F2 Bedienungsanleitung

Intermec

Intermec EasyCoder C4 Bedienungsanleitung

Intermec

Intermec EasyCoder F2 Bedienungsanleitung

Intermec

Intermec EasyCoder F2 Bedienungsanleitung

Intermec

Intermec PM4I Bedienungsanleitung

Intermec

Intermec EasyCoder 301 Handbuch

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung