Intermec PR2 Bedienungsanleitung

Product Name: Mobile Receipt Printer

Brand Name: Intermec

Model No: PR2/PR3

User’s Guide

Introduction

PR2/PR3 is a value entry performance mobile receipt printer. PR2 refers to a 2” Printer whereas PR3

corresponds to 3” Printer.

The differentiators of PR2/PR3 are:

a) Low system integration and management cost

b) Smallest Size

c) Lowest Weight

d) Fastest throughput

A PR3 printer is shown in Figure 1 (Top View)

Figure 1: A PR3 Printer (Top View)

The Front view of the printer is shown in Figure 2

Door Buttons

Tear Bar

LED Indicators

Power Button

Feed Button

LED Indicators

LED Name

LED Behavior and States

Ready-To-Work

Steady Blue = Printer is on and Ready-to-Work.

Flashing Blue: 50% duty cycle, 0.75 Hz = Printer

is on, but not ready to work or there is a critical

error.

Off = Printer is off or in deep sleep mode.

Connectivity

Flashes White: for 0.04 seconds for each packet

sent or received = Printer is communicating with

host (actively sending data)via USB, IrDA,

Bluetooth, or WiFi 802.11 radio.

Off = No data is being sent or received.

Battery

Off Charger

Off = Battery does not have a low charge.

Flashing Red: 25% duty cycle, 1 Hz = The

battery has a low charge.

On Charger

Steady Green = The printer is connected to

external power, and the battery is more than

95% charged.

Pulsing Green: (The output to the LED should be

driven with a pulse width modulated (PWM)

signal. The frequency used should be above the

human perception of any flicker. The difference

between PWM duty cycle changes should be

small enough so that there is no discernable

jump in output brightness. The duty cycle should

linearly change for 1.35 seconds to maximum

brightness, linearly change for 1.35 seconds to

minimum brightness and then remain off for 0.80

seconds. The resulting period of 3.50 seconds is

for a complete cycle from off to maximum

brightness and back to the off condition.) = The

printer is connected to external power and the

battery is charging and the battery is between

75% and 95% charged

Steady Red = the printer is connected to external

power and the battery is charging, and the

battery is between 0% and 75% charged

Flashing Amber at 50% duty cycle, 1 Hz = The

battery is out of charging temperature range.

Flashing Red at 50% duty cycle, 1 Hz = There is

a battery error.

Critical Error

Steady Red = Critical errors –cannot continue:

Door Open, Out of Paper, or Printhead is too hot

Off = No critical errors are present.

Magnetic Card Reader

Flashes Green 3 times in one second = Card

was read successfully

Flashes Red 1 time at 50% duty cycle, 1 Hz =

Card was read unsuccessfully

Off = Card reader is not being used.

Standard Communication Interfaces

There are various printer configurations based on the type of communication interfaces present in the

printer.

All configurations of the printer have USB communication.

Apart from USB, one of the following interfaces will be present

Bluetooth (FCC ID: EHA-INBT01; IC ID: 1223A-INBT01)

Wi-Fi

IrDA

Power Supply

The Printer is powered by a 2-cell battery pack with 8.4V, 1620mAh capacity.

Additionally, the battery is charged by using an external AC adapter which comes along with the printer

unit.

Print Test Page

To print a test page, press the feed button for a considerable duration (about 10 seconds) when the printer

is booting up.

Product operating temperature: -10 ~ 50 degree (discharge between -10 ~ 50 degree)

The battery charging mode to the operating temperature is only 40 degree.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Andere Handbücher für PR2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intermec Drucker Handbücher

Intermec

Intermec PM4I Bedienungsanleitung

Intermec

Intermec 3400 Bedienungsanleitung

Intermec

Intermec EasyCoder 7421 Bedienungsanleitung

Intermec

Intermec EasyCoder PF8 Bedienungsanleitung

Intermec

Intermec EasyCoder 101 Handbuch

Intermec

Intermec PM43 Bedienungsanleitung

Intermec

Intermec OKICODER 60 Bedienungsanleitung

Intermec

Intermec PB50 Bedienungsanleitung

Intermec

Intermec EasyCoder 7421 Bedienungsanleitung

Intermec

Intermec EasyCoder PX4i Bedienungsanleitung

Intermec

Intermec ColorCoder 901 Bedienungsanleitung

Intermec

Intermec EasyCoder PX4i Bedienungsanleitung

Intermec

Intermec 4630 Bedienungsanleitung

Intermec

Intermec EasyCoder PF2i Montageanleitung

Intermec

Intermec EasyCoder PF4i Bedienungsanleitung

Intermec

Intermec PB50 Bedienungsanleitung

Intermec

Intermec PB3 Series Bedienungsanleitung

Intermec

Intermec PF8T Bedienungsanleitung

Intermec

Intermec EasyCoder PL4 Bedienungsanleitung

Intermec

Intermec PF8D Bedienungsanleitung

Intermec

Intermec EasyCoder PX4i Bedienungsanleitung

Intermec

Intermec EasyCoder PF8 Bedienungsanleitung

Intermec

Intermec PB2 Series Bedienungsanleitung

Intermec

Intermec PW50 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung