Intersan SANISPRAY Montageanleitung

SANISPRAY

Individual Foot (IF)

Maintenance & Repair Guide

INTERSAN MANUFACTURING COMPANY

1748 W. Fillmore St. - Phoenix, Arizona 85007 - Tel 602.254.3101 - Fax 602.254.1776

a. Cleaning the Stainless Steel bowl

We recommend regularly cleaning the bowl with a sponge or soft cloth and soap. Otherwise a

slightly damp cloth can be used to remove debris. If necessary, areas with hard water or more

tenacious deposits can be treated with cream cleaners. In some cases the cream cleaner and soap

may not be enough. Lime scale and other deposits can be dissolved with a 25% solution of vinegar

and water. After cleaning, rinse the stainless steel bowl with plenty of fresh water and dry with a

soft cloth. Extended contact with, salt or disinfectants that contain bleach (sodium hypochlorite)

products should be avoided. Always dilute these “sanitizing” products before using and rinse

thoroughly afterwards. Using steelwool or hard abrasive powders are not recommended for stainless

steel products.

b. Servicing the Stainless Steel Soap Dispenser

Unlocking the circular cover and lifting it up makes the soap dispenser accessible for filling and

cleaning purposes.

CAUTION: Certain iodine based and other surgical soaps are not suitable for use in our liquid soap

valve. Please contact Intersan if you have questions weather or not a certain soap can

be used. If needed we can provide the appropriate soap valve.

c. Cleaning the spray nozzles.

Sediments can block the nozzle openings and cause an inconsistent spray or low flow.

- Clean all dirt, deposits and lime on the nozzle and especially at the spray openings with a wire

INTERSAN MANUFACTURING COMPANY

1748 W. Fillmore St. - Phoenix, Arizona 85007 - Tel 602.254.3101 - Fax 602.254.1776 - www.IntersanUS.com

NOTE: THIS INFORMATION IS SUBJECT TO CHANGE WITHOUT FORMAL NOTICE REV1.0

- 2 -

SANISPRAY INDIVIDUAL FOOT - Service Guide

INTERSAN®SANISPRAY

1. Preliminary

2. General Service

This manual has been written to provide maintenance personnel with adequate guidelines for service

and repair.

Using the instructions outlined in this manual will keep the Sanispray washfountain trouble-free and

will greatly simplify any repair work that might be needed.

APRIL03

Pic. 2

Pic. 1

NOTE: THIS INFORMATION IS SUBJECT TO CHANGE WITHOUT FORMAL NOTICE REV1.0

INTERSAN MANUFACTURING COMPANY

1748 W. Fillmore St. - Phoenix, Arizona 85007 - Tel 602.254.3101 - Fax 602.254.1776 - www.IntersanUS.com

- 3 -

2. General Service (continued)

d. Cleaning Strainers

The strainer screens must be periodically removed from the strainers and cleaned thoroughly. If

necessary replace the screens.

Each unit has at least 2 strainer screens. Be sure to check all of them. This will prevent excessive

reduction of the waterflow in the supply lines.

1. Check the Y-strainers (picture 3).

2. Inspect the strainer screen located in the inlet of the bracket assembly (picture 4).

3. Check the strainer screen installed in the head at the inlet of the plastic manifold (picture 5).

In case you have a copper manifold, there is a strainer at the inlet of each valve (pic. 6).

SANISPRAY INDIVIDUAL FOOT- Service Guide

INTERSAN®SANISPRAY

e. Cleaning Drain and Trap

*The beehive drain grid may be cleaned from the outside by turning the grate with a screwdriver

(picture 7).

*In case of excessive deposits in the waste water collector underneath the bowl:

-A chemical drain opener may be used if permitted by local authorities.

-A drain snake or similar device can be used by bending the drain grate inward while using the

device, then pulling the grate back out to its original position.

*The P-trap may be cleaned by removing either the cap or the flexible drain connector (picture

Pic. 5 Pic. 6

cap

flexible

APRIL03

Pic. 6

Pic. 3 Pic. 4

Pic. 5

Pic. 7 Pic. 8

NOTE: THIS INFORMATION IS SUBJECT TO CHANGE WITHOUT FORMAL NOTICE REV1.0

INTERSAN MANUFACTURING COMPANY

1748 W. Fillmore St. - Phoenix, Arizona 85007 - Tel 602.254.3101 - Fax 602.254.1776 - www.IntersanUS.com

- 4 -

2. General Service (continued)

f. Cleaning out the Drainpan

SANISPRAY INDIVIDUAL FOOT - Service Guide

INTERSAN®SANISPRAY

APRIL03

Step 1

Turn off the water supply to the

unit. Remove the allen screws &

flexible supply at the head.

Step 2

Remove the vent cap by loosening

the four screws and disconnecting

the flexible supply

Step 3

Remove the tie nut, tie plate and

the riser column.

Step 4

Remove the drain base & strainer

ring screen.

Step 5

Remove the bowl

Step 7

Reinstall in reverse order.

f. Cleaning Drainpan and Trap

Step 6

Now you can easily clean out the

drain pan.

INTERSAN MANUFACTURING COMPANY

1748 W. Fillmore St. - Phoenix, Arizona 85007 - Tel 602.254.3101 - Fax 602.254.1776 - www.IntersanUS.com

NOTE: THIS INFORMATION IS SUBJECT TO CHANGE WITHOUT FORMAL NOTICE REV1.0

- 5 -

3. Service Individual Foot Controls

Periodic inspection of the foot control components may be necessary.

SANISPRAY INDIVIDUAL FOOT - Service Guide

INTERSAN®SANISPRAY

APRIL03

2919

2920

2063

2917

2916

2869

2916

2869

2917

Checking for air leaks:

Each foot push-button remotely activates a valve inside the head. This is a closed system and any air leaks

will compromise the cycle duration or activation. First make sure that each end of the tubing connection is tight

and secure from the foot pushbutton (FPB) to the valves, then check the bladder (P2919) for cracks.The

air bladder and tubing connections are serviced by removing the single allen screw (P2030) and sliding the

cover forward on the foot pushbutton.The valves (P5015) are located in the sprayhead, remove the cover for

inspection. If nothing is loose, next disconnect the tubing (P2869) from the valve and cover the loose end of the

tubing and compress the bladder, check for air leaking back inside the bladder. Recheck the bladder

condition. Recheck the fitting connections at both sides of valves and at pushbutton housings for possible cracks

or stripped threads.

INTERSAN MANUFACTURING COMPANY

1748 W. Fillmore St. - Phoenix, Arizona 85007 - Tel 602.254.3101 - Fax 602.254.1776 - www.IntersanUS.com

NOTE: THIS INFORMATION IS SUBJECT TO CHANGE WITHOUT FORMAL NOTICE REV1.0

- 6 -

SANISPRAY INDIVIDUAL FOOT - Repair Guide

INTERSAN®SANISPRAY

4. Troubleshooting Individual Foot Unit

APRIL03

Unlock and remove the cover

B. Washfountian fails to shut off.

Replace the following parts

P5040,P5041 and HUBASPRING

Unlock and remove the lid.

Remove the four screws and

seperate the valvefrom the brass

Clean brass water housing with

Scotchbritetm type product.

Reinstall in the reverse order

making sure the air tubing blue

nut is pointing towards the top

of the head. Use Teflon tape on

the nozzle fitting for a leak-

proof connection to the valve.

Check that the nozzle is pointing

straight downward. Double

check for any water leaks inside

and out.

Remove the access cover and

turn off the water supply to

the unit.

Disconnect the water tubing from

the valve by pushing in on the blue

ferrel and pulling on the tubing.

Remove the nozzle fitting from

the outside of the head.

Inspect and clean the water

housing if rust or mineral

deposits are present.

Remove the four screws and

disassemble the grey portion from

the brass section.

A. Insufficient waterspray when activating the valve

1. Check to see if the main supplies are open, the water heating system is on and the stop valves

inside the pedestal are open.

2. If the flow is inconsistent between valves, check the condition of the screen at each valve inlet (in case you have

a plastic manifold: check the screen at the inlet of the manifold) .

Service when necessary (see page 3- Clean Strainers).

3. Check the water pressure at the inlet of the control valve. The Sanispray requires a minimum of 17 psi

when the washfountain is spraying.

4. Check the strainer screens. If necessary clean or replace them (see page 3 - Clean Strainers).

5. Check to see if sediments are blocking the nozzles (see page 2 - Cleaning the nozzles).

D. The Spraywater is Cold

1. Check to see if the water heating system supplying the unit is on. The temperature of the

hot water at the inlet of the thermostatic mixing valve should be between 130oand 167oF.

The water pressure at the inlet of the thermostatic mixing valve should be such that a minimum

of 17 psi of flowing pressure is obtained at the inlet of the control valve.

2. Check to see if the hot & cold water supply lines are connected to the right inlets of the

thermostatic mixing valve. The thermostatic mixing valve is marked with H for hot water and

C for cold water.

INTERSAN MANUFACTURING COMPANY

1748 W. Fillmore St. - Phoenix, Arizona 85007 - Tel 602.254.3101 - Fax 602.254.1776 - www.IntersanUS.com

NOTE: THIS INFORMATION IS SUBJECT TO CHANGE WITHOUT FORMAL NOTICE REV1.0

- 7 -

SANISPRAY INDIVIDUAL FOOT - Repair Guide

INTERSAN®SANISPRAY

4. Troubleshooting Individual Foot Unit

Try sticking your fingers between the drainpan and the

bowl. If you feel a gap, the bowl has been installed

incorrectly. To reinstall the bowl correctly, follow the

next steps.

APRIL03

C. Water Hammer

1. Measure the water pressure at the inlet of the control valve. The Sanispray works properly

between 17 and 100 psi. If the pressure is higher, close the ball valves on the hot and cold

supplies inside the pedestal to the point where there is still a nice waterspray and a minimum

of 17 psi water pressure.

Disconnect the water flexible

supply from manifold and push

inside the column.

Remove the four allen screws

and lift the head from the

pedestal.

A. Insufficient waterspray when activating the valve

1. Check to see if the main supplies are open, the water heating system is on and the stop valves

inside the pedestal are open.

2. If the flow is inconsistent between valves, check the condition of the screen at each valve inlet.

Service when necessary (see page 3- Clean Strainers).

3. Check the water pressure at the inlet of the control valve. The Sanispray requires a minimum of 17 psi when

the washfountain is spraying.

4. Check the strainer screens. If necessary clean or replace them (see page 3 - Clean Strainers).

5. Check to see if sediments are blocking the nozzles (see page 2 - Cleaning the nozzles).

B. Water Hammer

1. Measure the water pressure at the inlet of the control valve. The Sanispray works properly between 17 and

100 psi. If the pressure is higher, close the ball valves on the hot and cold supplies inside the pedestal to the

point where there is still a nice waterspray and a minimum of 17 psi water pressure.

C. The Washfountain Fails to Shut off.

Remove the access cover and

turn off the water supply to

the unit.

E. Leaking drainpan

INTERSAN MANUFACTURING COMPANY

1748 W. Fillmore St. - Phoenix, Arizona 85007 - Tel 602.254.3101 - Fax 602.254.1776 - www.IntersanUS.com

NOTE: THIS INFORMATION IS SUBJECT TO CHANGE WITHOUT FORMAL NOTICE REV1.0

- 8 -

SANISPRAY INDIVIDUAL FOOT - Repair Guide

INTERSAN®SANISPRAY

4. Troubleshooting Individual Foot Unit

The drainpan should be tight to

the bowl without any gap. Double

check to make sure. If there is still

a gap, repeat the previous steps

F. Soap is Leaking from the Liquid Soap Valve

The soap valve is probably installed incorrectly. Make sure that the O-ring of the soap valve is

on the inside of the soap dispenser. If necessary remove the soap in the dispenser and reinstall

with the O-ring between the nut and the reservoir liner.

APRIL03

Loosen the 2 bolts at both sides

of the pedestal.Tighten the tie nut at the top of

the unit very firmly.Tighten the 2 bolts at each side

of the pedestal.

Reinstall the soap dispenser and

flexible supply line.

A. Insufficient waterspray when activating the valve

1. Check to see if the main supplies are open, the water heating system is on and the stop valves

inside the pedestal are open.

2. If the flow is inconsistent between valves, check the condition of the screen at each valve inlet.

Service when necessary (see page 3- Clean Strainers).

3. Check the water pressure at the inlet of the control valve. The Sanispray requires a minimum of 17 psi when

the washfountain is spraying.

4. Check the strainer screens. If necessary clean or replace them (see page 3 - Clean Strainers).

5. Check to see if sediments are blocking the nozzles (see page 2 - Cleaning the nozzles).

B. Water Hammer

1. Measure the water pressure at the inlet of the control valve. The Sanispray works properly between 17 and

100 psi. If the pressure is higher, close the ball valves on the hot and cold supplies inside the pedestal to the

point where there is still a nice waterspray and a minimum of 17 psi water pressure.

C. The Washfountain Fails to Shut off.

Reinstall the head and the

flexible supply line. Turn on the water supply to

the unit and reinstall the access

cover.

Inhaltsverzeichnis

Andere Intersan Küchen- und Badezimmerausstattung Handbücher

Intersan

Intersan Modus-Vivendi ES Series Bedienungsanleitung

Beliebte Küchen- und Badezimmerausstattung Handbücher anderer Marken

Grohe

Grohe BRIDGEFORD 33 870 Bedienungsanleitung

Hans Grohe

Hans Grohe Zenio Metro 31811000 Bedienungsanleitung

Gröne

Gröne Zedra 32 555 Bedienungsanleitung

Transform

Transform QL045 Bedienungsanleitung

Sanela

Sanela SLU 09PTB Bedienungsanleitung

Glacier bay

Glacier bay FP4A0052BNV Montageanleitung

Lefroy Brooks

Lefroy Brooks C1-1400 Montageanleitung

Grohe

Grohe Rapido E Bedienungsanleitung

Danze

Danze D302455 Bedienungsanleitung

Waterworks

Waterworks CEKM30 Merkblatt

Helvex

Helvex Omega TV-298 Bedienungsanleitung

Tribata.

Tribata. GEORGIAN G5393 Bedienungsanleitung

Alpha Bidet

Alpha Bidet Alpha One Bedienungsanleitung

InSinkErator

InSinkErator H/HC3300 Installationshandbuch

Clou

Clou Xo type 1 Bedienungsanleitung

Kohler

Kohler Contra 26448T-4 Bedienungsanleitung

Grohe

Grohe Bridgeford 20 158 Bedienungsanleitung

Hans Grohe

Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Bedienungsanleitung