Intersil ISL97671A Bedienungsanleitung

ISL97671A, ISL97672A Evaluation Board Quick Start

Guide

Description

This quick start guide pertains to the ISL97671A, ISL97672A

Evaluation Board Rev A-1 (Oct 2011). This board comes

populated with 78 LED’s in 6P13S configuration to simplify

evaluation and testing. In the case of the ISL97671A

evaluation board, please install the Sunlight ISL97670 GUI,

which will be used to control these parts via I2C. Please note

that the slave address on the ISL97671A is hexadecimal 58;

see Figure 1. Please refer to respective the ISL97671A or

ISL97672A section for jumper settings and power up

instructions.

ISL97671A

1. ISL97671A LED strings can be configured in 6P13S,

6P12S, 6P11S, and 6P10S with different LED jumper

settings, as shown in Table 1.

2. Connect WR, JP_OUTPUT, and JPCH0-JPCH5. Leave JP1

open to use external fault protection FET (Q1).

3. For current LED configuration, connect jumper JP1A to the

left and connect the power supply on J99 (IC_VIN) to deliver

VIN to the IC. When there is less LED in each string and

VOUT is lower than 28V, IC_VIN can be configured as the

bootstrap generated from the boost output by connecting

the jumper JP1A to the right

4. IC Enable is shorted to VIN by connecting jumper JP2A to

the right, thereby shorting jumper JP2A to the left so that

the EN is driven by J98(EN)

5. VLOGIC level for I2C can be generated from VDC by

connecting jumper JP3A to the right. VLOGIC can be driven

from J97 (VLOGIC) by shorting jumper JP3A to the left.

6. The configuration of VIN (JP1A), EN (JP2A), and VLOGIC

(JP3A) can be quickly found by referring to the table printed

on the evaluation board, as shown in Figure 3.

7. There are 4 different operation modes for ISL97671A. The

setting for each mode is shown on the other table printed

on the evaluation board, as shown in Figure 3.

8. For I2C/SMBUS and DPST mode, connect the I2C interface

board to the ISL97671A evaluation board, as shown in

Figure 2.

9. For I2C/SMBUS and DPST mode, in order to enable the

board, write a hex 58 for Slave Address and write a hex 05

in register 01; writing a hex 01 in register 01 will enable

DPST (see data sheet for more details); writing a hex 03 in

FIGURE 1. EXAMPLE OF GUI INTERFACE

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 1-888-468-3774 |Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.

All other trademarks mentioned are the property of their respective owners.

June 13, 2012

AN1634.1

Application Note 1634

2AN1634.1

10. The LED current can be programmed by varying POT R15

using the following equation:

The measured current divided by six is the LED current per

channel. For example, 120mA measured current will correspond

to 20mA/channel.

11. The PWM dimming frequency can be adjusted by varying pot

R11 using the following equation:

ISL97672A

1. ISL 97672A LED strings can be configured in 6P13S, 6P12S,

6P11S, and 6P10S with different LED jumper settings, as

shown in Table 1.

2. Connect WR, JP_OUTPUT, and JPCH0-JPCH5. Leave JP1 open

to use external fault protection FET (Q1).

3. For current LED configuration, connect jumper JP1A to the left

and connect the power supply on J99 (IC_VIN) to deliver VIN to

the IC. When there is less LED in each string and VOUT is lower

than 28V, IC VIN can be configured as the bootstrap

generated from the boost output by connecting the jumper

JP1A to the right.

4. IC Enable is shorted to VIN by connecting jumper JP2A to the

right, thereby shorting jumper JP2A to the left so that EN is

driven by J98 (EN).

5. VLOGIC level can be generated from VDC by connecting

jumper JP3A to the right. VLOGIC can be driven from J97

(VLOGIC) by shorting jumper JP3A to the left.

6. Configuration of VIN (JP1A), EN (JP2A), and VLOGIC (JP3A)

can be quickly found by referring to the table printed on the

evaluation board, as shown in Figure 3.

7. There is only one operation mode for ISL97672A, and the

settings for JP4A, JP5A, J81, JP91, R10, and JP92 need to

follow the table printed on the evaluation board, as shown in

Figure 3.

8. The boost switching frequency can be adjusted by varying pot

R11 using the following equation:

TABLE 1. LED STRINGS CONFIGURATIONS WITH DIFFERENT JUMPER

SETTINGS

LED CONFIGUATRION 6P13S 6P12S 6P11S 6P10S

JP_OUTPUT Short

JP_CH0

Short

JP_CH1

JP_CH2

JP_CH3

JP_CH4

JP_CH5

SH1_LED0

Open Short Open Short

SH1_LED1

SH1_LED2

SH1_LED3

SH1_LED4

SH1_LED5

SH2_LED0

Open Open Short Short

SH2_LED1

SH2_LED2

SH2_LED3

SH2_LED4

SH2_LED5

(EQ. 1)

ILED 410.5 R15 R16+()410.5 R13⁄=⁄=

(EQ. 2)

FPWM 6.66 107R11 R12+()⁄×=

(EQ. 3)

Fsw 510

×()R11 R12+()⁄=

FIGURE 2. I2C INTERFACE BOARD CONNECTED TO THE ISL97671A EVALUATION BOARD

Application Note 1634

3AN1634.1

FIGURE 3. SETTINGS OF IC VIN, ENABLE, AND VLOGIC ARE SHOWN ON PCB IN YELLOW RECTANGE ON THE LEFT-HAND SIDE. CONFIGURATIONS OF 4 DIFFERENT OPERATION MODES ARE

LISTED ON PCB IN YELLOW RECTANGE ON THE RIGHT-HAND SIDE.

Application Note 1634

4AN1634.1

FIGURE 4. TOP VIEW OF ISL97671A/ISL97672A EVALUATION BOARD

Application Note 1634

5AN1634.1

FIGURE 5. BOTTOM VIEW OF ISL97671A/ISL97672A EVALUATION BOARD

Application Note 1634

6AN1634.1

FIGURE 6. SCHEMATIC OF ISL97671A ISL97672A EVALUATION BOARD

Title

Size:

Date:

File:

Revision:

Sheet

Drawn By:

Error : intersil.bmp file not found.

Terry Nguyen

09/2011

0.1uF/50V

1uF/10V

15uH(Coilcraft)

PMEG6030

R2A

10K

358K

100pF/50V

C10

J98 (EN)

J4 (SDA)

SDA / FLAG

J3 (SCL)

SCL

J1(Boost in)

Boost Vin

J9A

4.7k R7

4.7k

J97 (I2C Vlogic)

Vlogic

JP1

10uF/50V

LED5_1

LED5_2

LED5_3

LED5_4LED5_5LED5_6LED5_7LED5_8LED5_9LED5_10LED5_11LED5_12LED5_13

LED4_1LED4_2

LED4_3

LED4_4

LED4_5LED4_6LED4_7LED4_8LED4_9LED4_10LED4_11LED4_12LED4_13

LED3_1LED3_2

LED3_3

LED3_4LED3_5

LED3_6

JP_CH5 JP_CH4 JP_CH3 JP_CH2

LED3_7

LED3_8LED3_9LED3_10LED3_11

LED3_12

LED3_13

LED2_1

JP_CH1

LED2_2

LED2_3

LED2_4LED2_5LED2_6

LED2_7

LED2_8

LED2_9

JP_CH0

LED1_3

LED1_4

LED1_5

LED1_6LED1_7

LED1_8LED1_9

LED1_10LED1_12LED1_13

LED0_1

LED0_2LED0_3

LED0_4

LED0_5

LED0_6

LED2_10LED2_11LED2_12LED2_13

LED1_1

LED1_11

LED0_7

LED1_2

LED0_8

LED0_9

LED0_10LED0_11LED0_12LED0_13

SH2_LED4 SH2_LED3 SH2_LED2 SH2_LED1 SH2_LED0SH2_LED5

C14

1nF

C13

1nF

C12

1nF

C11

1nF

C15

1nF

C16

1nF

CH4

CH5

C3 ~ C6 : 4.7uF/50V X7R

ceramic caps

C4~C6 are reserved pads

CH0

CH1

CH2

CH3

J10(Vout)

Vout JP_OUTPUT

SDA

SCL

J9(VDC)

VDC

For 2 layers

board, connect

top layer PGND

and bottom laye

AGND at one

point such that

using the

thermal pad as a

single

SH_LED13

SH_LED12

SH_LED11

SH_LED10

FAULT

VIN

VDC

PWM

SMBDAT or SDA / FLAG

SMBCLK or SCL / NC

FPWM / FSW

AGND 9

CH0 10

CH1 11

CH2 12

CH3 13

CH4 14

CH5 15

OVP 16

RSET

COMP

PGND 19

LX 20

PAD C

ISL97671A/72A

J81 (PWMI_direct)

PWMI

HDR1

INTERFACE

FDMA530PZ

1 2

C18

C19

0.1uF

J99( IC Vin)

IC Vin

Vin=Bootstrap

IC Vin=

header

VDC

SCL_S

EN selection

IC VIN selection

SCL_IC

SDA_IC

SCL_IC

EN=IC Vin

(Right)

EN=J98 header

(Left)

SDA_IC

SDA_S

SCL_S

VDC

I2C / FLAG Vlogic selection

Vlogic=J97

header

Vlogic=VDC

(Right)

JP1A

JP2A

JP3A

JP5A

JP4A

JP91

JP92

VDC

ISET

R13

R15

R16

R14

R11

750K

R12

2.21K

R10

C20

390pF

10k

3.3nF

ISL97671_2A EVAL SCHEMATIC

SH3-4

SH2-3

SH1-2

SH5-6

nc SH4-5 nc

SDA_S

SH1_LED4 SH1_LED3 SH1_LED2 SH1_LED1 SH1_LED0

SH1_LED5

Application Note 1634

7AN1634.1

TABLE 1. BOM FOR ISL97671A/ISL97672A EVALUATION BOARD

PART TYPE DESIGNATOR FOOTPRINT

0 R14 402

0R10402

0.1uF C19 402

0.1µF/50V C2 402

1M R15 VRES

1nF C11 603

1nF C14 603

1nF C16 603

1nF C13 603

1nF C12 603

1nF C15 603

1µF/10V C7 402

2.21k R12 402

3.3nF C8 402

4.7k R6 603

4.7k R7 603

4.7µF/50V C5 1210

4.7µF/50V C6 1210

4.7µF/50V C3 1210

4.7µF/50V C4 1210

5k R16 402

10k R2A 402

10k R2 402

10µF/50V C1 1210

15µH (Coilcraft) L1 XAL6060-153MEB

100pF/50V C9 402

358K R1 402

390pF C20 402

750k R11 VRES

FDMA530PZ Q1 microFET2x2

INTERFACE HDR1 MOLEX22-05-3101

ISL97671A/72A U1 LPP20.3X4

LED-SMT ALL LEDs LW_Y87C

PMEG6030 D1 SOD-123W

nc SH4-5 402

nc C10 402

nc R13 402

nc C18 402

nc R9 402

nc SH3-4 402

Application Note 1634

Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is

cautioned to verify that the Application Note or Technical Brief is current before proceeding.

For information regarding Intersil Corporation and its products, see www.intersil.com

AN1634.1

nc SH5-6 402

nc SH1-2 402

nc SH2-3 402

TABLE 1. BOM FOR ISL97671A/ISL97672A EVALUATION BOARD (Continued)

PART TYPE DESIGNATOR FOOTPRINT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intersil Hauptplatine Handbücher

Intersil

Intersil ISL8216MEVAL1Z Bedienungsanleitung

Intersil

Intersil ISL6228EVAL3Z Bedienungsanleitung

Intersil

Intersil ISL59442EVAL1 Bedienungsanleitung

Intersil

Intersil ISL281X7MSOPEVAL1Z Bedienungsanleitung

Intersil

Intersil ISL85009EVAL1Z Bedienungsanleitung

Intersil

Intersil ISL9519EVAL1Z Handbuch

Intersil

Intersil ISL45042EVAL1Z Bedienungsanleitung

Intersil

Intersil QHx220 Installationshandbuch

Intersil

Intersil ISL73033SLHEV1Z Bedienungsanleitung

Intersil

Intersil ISL32740EVAL2Z Bedienungsanleitung

Intersil

Intersil ISL71831SEH Bedienungsanleitung

Intersil

Intersil ISL6252AEVAL2Z Handbuch

Intersil

Intersil ISL8033DEMO1Z Bedienungsanleitung

Intersil

Intersil ISL6443AEVAL2Z Montage- und Bedienungsanleitung

Intersil

Intersil ISL70321SEHEV Z Series Bedienungsanleitung

Intersil

Intersil ISL1208 Montage- und Bedienungsanleitung

Intersil

Intersil ISL5761EVAL1 Bedienungsanleitung

Intersil

Intersil ISL72813SEHEV1Z Bedienungsanleitung

Intersil

Intersil ISL6227EVAL1 Handbuch

Intersil

Intersil ISL32740EVAL1Z Bedienungsanleitung

Intersil

Intersil ISL6294AEVAL1Z Gebrauchsanweisung

Intersil

Intersil ISL35411 Bedienungsanleitung

Intersil

Intersil ISL8018EVAL3Z Bedienungsanleitung

Intersil

Intersil ISL59420/21EVAL1 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung