4 INTEX GIRAFFE & OKAPI MANUAL - intex.com.au | intex.co.nz intex.com.au | intex.co.nz - INTEX GIRAFFE & OKAPI MANUAL 5
Use safety equipment. Always wear eye protection. Safety equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
Avoid accidental starting. Be sure switch is off before plugging in. Plugging in
tools that have the switch on invites accidents.
Remove adjusting keys or switches before turning the tool on. A wrench or a key
that is left attached to a rotating part of the tool may result in personal injury.
Do not overreach. Keep a proper footing and balance at all times. Proper footing
and balance enables better control of the tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
TOOL USE & CARE
Do not force tool. Use the correct tool for your application. The correct tool will
do the job better and safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off. Any tool that cannot be
controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing the tool. Such preventive safety measures
reduce the risk of starting the tool accidentally.
Store idle tools out of reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Tools are
dangerous in the hands of untrained users.
Maintain tools with care. Properly maintained tools are less likely to bind and are
easier to control.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tools operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Use the power tool, accessories, in accordance with these instructions and in
the manner intended for the particular type of power tool, taking into account
the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
SERVICE
Have your tool serviced by a qualified repair person using only identical replacement
parts. NOTE: WE RECOMMEND THAT THE TOOL SHOULD BE SERVICED
AT LEAST ONCE A YEAR. This will ensure that the safety of the power tool is maintained.
WARNING: To reduce the risk of injury, user must read instruction manual.
Symbols used in this manual
V volts
A mperes
Hz hertz
W watt
~ alternating current
n0 no load speed
/min revolutions or reciprocation per minute
class II tool
SPECIFIC SAFETY RULES
1. Keep hands away from rotating sanding head area at all times!
2. Prolonged breathing of airborne dust from drywall sanding may effect respiratory
function: Always use a vacuum cleaner with a bag approved for drywall dust
installed.Always wear a respirator approved for dust and mist.
3 . Sanding LEAD-BASED paint is extremely toxic and should not be attempted.
Only allow professionals with special training and equipment perform this task.
4. Maintain proper footing and balance at all times. Do not overreach.
Use proper scaffolding.
5. Always wear appropriate safety equipment when operating.
6. Important: After completing sanding, switch off the switch and wait for the
coasting sanding head to stop completely before putting the tool down.
7. Never operate the tool in an area with flammable solids, liquids, or gases. Sparks
from the commutator/carbon brushes could cause a fire or explosion.
8. There are certain applications for which this tool was designed. The manufacturer
strongly recommends that this tool NOT be modified and/or used for any
application other than for which it was designed. If you have any questions relative
to its application DO NOT use the tool until you have written the manufacturer and
have been advised.
9. Use machine with both hands at all times. Loss of control can cause personal injury.
10. Keep power supply cord clear from the working range of the machine. Always lead
the cable away behind you.
11. Immediately switch off the machine if unusual vibrations or if other malfunctions
occur. Check the machine in order to find out the cause.
12. The dust that arises when working with this tool can be harmful to health.
Use a dust absorption system and wear a suitable dust protection mask and
remove deposited dust with a vacuum cleaner.
