Invacare Aquatec ORCA Einrichtungshandbuch

INSTRUCTION FOR REPAIR

Aquatec

Orca, Orca XL

V P&M 04

Revision 01 issued: 28.11.2006 UW

changed: 30.01.2007 UW

Instruction for Repair – Orca, Orca XL

Revision 01 Page 1 of 7 Issued: 28.11.2006 UW

Changed: 03.07.2007 UW

Part no. 1471121

NOTE!

•Repairs may only be done by authorised dealers.

•Risk is assigned to the executor with repairs.

•Solely use original spare parts for repairs.

•Repairs and serial numbers of replaced parts have to be documented.

•Professional and safe repairs can be done by INVACARE

AQUATEC

Before starting the repair please read the referring chapters of the repair

instructions thoroughly!

HAZARD NOTE! Increased risk of jamming and squeezing with all works related

to the lifting mechanism within the area of the scissors!

NOTE! The sequence of work has to follow according to the repair

instructions!

I. REPAIR INSTRUCTIONS SEAT

The seat – consisting of base plate, lifting scissors and seat plate – is available

as one complete spare part.

NOTE:

•Seat of Orca (1471050) with a straight end at the back side.

•Seat of Orca XL (1471103) with a curved end at the back side and an

additional „XL“-mark on the lifting scissor.

Below the assembly of attachment parts:

Pic 1

Pic 2

Pic 3

Attachment parts in the area of the spindle foot

1. Insert the flat spring (15415) into the base plate in the right positional

arrangement. The opening angle shows to the back edge of the base

plate.

2. Insert latch (16449) into base plate directly above the flat spring.

3. Insert bushing latch (16448) into the base plate coming bottom-up.

NOTE: Bear against the latch while pressing the bushing latch into

the base plate.

4. Slip pressure springs (2x 16794) onto the pins of the base plate.

5. Slip lockings (16791 + 16792) onto the pressure springs and press them

into the base plate. Before pressing first apply the locking inclined.

NOTE: Consider different lockings (left and right).

NOTE: The locking has to engage audible.

6. Function test of lockings: Lockings can be pressed down and are

returned into their home position.

Pic 4

Pic 5

Pic 6

Pic 7

Pic 8

INSTRUCTION FOR REPAIR

Aquatec

Orca, Orca XL

V P&M 04

Revision 01 issued: 28.11.2006 UW

changed: 30.01.2007 UW

Instruction for Repair – Orca, Orca XL

Revision 01 Page 2 of 7 Issued: 28.11.2006 UW

Changed: 03.07.2007 UW

Part no. 1471121

Attachment parts in the area of the base plate

1. Screw in the suction cups with thread (2x 15071) into the rear threads of

the base plate.

2. Feed in the suction cups with toggle (2x 15072) coming bottom-up

through the opening at the front end of the base plate and pull them to

the front. The strap shows to the rear end. Pull the suction cup until the

nib at the suction cup ends in the slot of the base plate. Then feed the

strap from bottom-up and fix it in the bearing at the end of the opening.

3. First thread the suction cup lid (2x 15121) from above onto the neck of

the suction cup then push it into the base plate.

NOTE: The suction cup lid has to engage audible.

Pic 9

Pic 10

Pic 11

Pic 12

Attachment parts in the area of the lifting scissors

1. Bolts (4x 15105) to fix the gliding shoe (4x 16446) at the lifting scissor.

The bolts are plugged into the corresponding openings at lifting scissors

and gliding shoe.

NOTE: Consider the bolts to be plugged from outside in.

2. Bolts (Orca: 4x 16679; Orca XL: 4x 1471088) to fix the lifting scissors at

seat and base plate. The bolts are plugged into the corresponding

openings at seat plate, base plate and lifting scissors.

NOTE: Consider the bolts of the base plate to be plugged from

outside in. The bolts of the seat plate to be plugged from inside

out.

NOTE: The stainless steel bolts of Orca XL have to be secured with

provided retaining ring. Retaining ring may not be overstretched!

3. In case of the thrust washer for the scissors needs to be replaced: Slide

on the thrust washer (2x 15344) onto the axle of the lifting scissors.

NOTE: The thrust washer has to engage audible.

Pic 13

Attachment parts in the area of the seat plate

Feed the guides of the side flaps (2x 15892) into the bearing of the seat

plate.

NOTE: Consider all three guides of the side flap engage audible.

II. REPAIR INSTRUCTIONS BACKREST

1. Position backrest (16440) upside down on the work bench.

2. Position actuator (Orca:16782, Orca XL: 1471062) on the backrest.

Therefore feed the bolt at the top edge of the backrest into the cut-out of

the actuator housing.

In order to feed in the spindle foot detaching one bolt might be required

NOTE: Consider the slot at the spindle being centered with the

clamp horse.

Pic 14

Pic 14a

INSTRUCTION FOR REPAIR

Aquatec

Orca, Orca XL

V P&M 04

Revision 01 issued: 28.11.2006 UW

changed: 30.01.2007 UW

Instruction for Repair – Orca, Orca XL

Revision 01 Page 3 of 7 Issued: 28.11.2006 UW

Changed: 03.07.2007 UW

Part no. 1471121

NOTE: Consider the cable to be under the tube and above the

upper tube fixation.

NOTE: Consider the proper alignment: The bulge of the spindle

foot faces to the top.

3. Turn the tube until the imaginary axle at the spindle foot is horizontal.

4. Wedge the spindle foot in this position.

5. Insert the nuts (4x 16779) into the slots of the clamp horse.

NOTE: The concave side faces to the screws, the short edge faces

towards the tube.

6. First insert the upper clamp (16778) into the cut-in of the tube.

NOTE: The taller side of the clamp faces towards the spindle foot.

7. Put on the washers (2x 16780) and tighten the clamp using the lens

head screws (2x 16781).

NOTE: Fix the screws with a torque of 4

+0,5

Nm.

8. Afterwards fix the lower clamp (16778) as specified with 6 and 7.

9. Mount the retaining ring (16456) on the axle (16793).

NOTE: Retaining ring may not be overstretched! Consider the

retaining ring to fit properly.

10.Hold the pulley (16450) into the holder of the spindle foot and insert the

axle.

11.Fix the axle with second retaining ring (16456).

NOTE: Retaining ring may not be overstretched! Consider the

retaining ring to fit properly.

12.Place the phone jack in its bed and pull it down to the bed stop.

13.Put on the holding device (16455) and fix it with the lens head screws

(2x 15348).

NOTE: Consider the edge-shape of the phone jack.

14.Plug in the left bolt (1470580) from outside into the slot of the spindle

foot.

NOTE: Chamfer of the bolt faces down and outside.

15.Snap in the thrust washer (15344) into the inner slot of the bolt.

NOTE: The nose of the thrust washer faces to the tube.

16.Repeat the steps 14 and 15 for the right bolt (1470579).

17.Function test of the bolts: Extend the spindle foot by 5cm (2”) and move

it back. The bolts have to be pressed out by the spindle foot. After the

spindle foot is back in its home position the bolts may be pressed back

again.

Pic 14

Pic 15

Pic 16

Pic 17

Pic 18

Pic 19

Pic 20

INSTRUCTION FOR REPAIR

Aquatec

Orca, Orca XL

V P&M 04

Revision 01 issued: 28.11.2006 UW

changed: 30.01.2007 UW

Instruction for Repair – Orca, Orca XL

Revision 01 Page 4 of 7 Issued: 28.11.2006 UW

Changed: 03.07.2007 UW

Part no. 1471121

III. FUNCTION TEST

1. Place the assembled backrest onto the seat plate and erect it.

2. Using a charged hand control all functions of the bathlift have to be

checked.

NOTE: Consider the bolts are returned into the slot of the spindle

foot while the backrest is reclining.

1: Base plate Orca 2: Base plate Orca XL

3: Lifting scissors of Orca XL 4: Flat spring

INSTRUCTION FOR REPAIR

Aquatec

Orca, Orca XL

V P&M 04

Revision 01 issued: 28.11.2006 UW

changed: 30.01.2007 UW

Instruction for Repair – Orca, Orca XL

Revision 01 Page 5 of 7 Issued: 28.11.2006 UW

Changed: 03.07.2007 UW

Part no. 1471121

5: Latch 6: Bushing latch

7: Pressure spring 8: Locking

9: Suction cup with thread 10: Suction cup with toggle

INSTRUCTION FOR REPAIR

Aquatec

Orca, Orca XL

V P&M 04

Revision 01 issued: 28.11.2006 UW

changed: 30.01.2007 UW

Instruction for Repair – Orca, Orca XL

Revision 01 Page 6 of 7 Issued: 28.11.2006 UW

Changed: 03.07.2007 UW

Part no. 1471121

11: Strap in bearing 12: Suction cup lid

13: Thrust washer of lifting scissors 14: Actuator

14a: Slot of spindle is centered with clamp horse

INSTRUCTION FOR REPAIR

Aquatec

Orca, Orca XL

V P&M 04

Revision 01 issued: 28.11.2006 UW

changed: 30.01.2007 UW

Instruction for Repair – Orca, Orca XL

Revision 01 Page 7 of 7 Issued: 28.11.2006 UW

Changed: 03.07.2007 UW

Part no. 1471121

15: Bulge of spindle foot Orca and Orca XL 16: Imaginary spindle foot axle

17: Nut 18: Pulley

19: Phone jack 20: Thrust washer of bolt

Andere Handbücher für Aquatec ORCA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Invacare Badezimmerhilfe Handbücher

Invacare

Invacare Stileo H171 Bedienungsanleitung

Invacare

Invacare CareGuard 95-2 Montageanleitung

Invacare

Invacare H407 Omega Bedienungsanleitung

Invacare

Invacare Aquatec Step Bedienungsanleitung

Invacare

Invacare Aquatec Sorrento 1532633 Bedienungsanleitung

Invacare

Invacare Aquatec Sorrento Bedienungsanleitung

Invacare

Invacare Aquatec ORCA Bedienungsanleitung

Invacare

Invacare H450 Bedienungsanleitung

Invacare

Invacare Aquatec ORCA Bedienungsanleitung

Invacare

Invacare Alize Bedienungsanleitung

Invacare

Invacare H160 Bedienungsanleitung

Invacare

Invacare Aquatec Trans Bedienungsanleitung

Invacare

Invacare Aquatec Pure Bidet Bedienungsanleitung

Invacare

Invacare Stileo H170 Bedienungsanleitung

Invacare

Invacare Izzo Bedienungsanleitung

Invacare

Invacare Hydraia 9670CE Montageanleitung

Invacare

Invacare Aquatec ORCA Bedienungsanleitung

Invacare

Invacare R8802 Bedienungsanleitung

Invacare

Invacare 9630E Styxo Montageanleitung

Invacare

Invacare R8803 Bedienungsanleitung

Invacare

Invacare H2080 Bedienungsanleitung

Invacare

Invacare Aquatec 90 Bedienungsanleitung

Invacare

Invacare 1148124 Montageanleitung

Invacare

Invacare 91-2 Montageanleitung

Beliebte Badezimmerhilfe Handbücher anderer Marken

Pressalit Care

Pressalit Care R2040 Bedienungsanleitung

Leckey

Leckey firefly splashy BIG Bedienungsanleitung

NRS Healthcare

NRS Healthcare H85350 Bedienungsanleitung

WENKO

WENKO 23285100 Bedienungsanleitung

Dietz SmartCare

Dietz SmartCare TAYO Bedienungsanleitung

Roth

Roth Mobeli 1400222H2S Bedienungsanleitung

SEVERIN

SEVERIN LB 7220 Bedienungsanleitung

ZACK

ZACK CARVO 40510 Bedienungsanleitung

Mobilex

Mobilex Kakadu Bedienungsanleitung

CareCo

CareCo BA07059 Programmierhandbuch

lopital

lopital Elexo Technisches Handbuch

lopital

lopital Tango XL Bedienungsanleitung

rainbow care

rainbow care FS697 Bedienungsanleitung

ALCO

ALCO AL-70734 Bedienungsanleitung

lifestyle mobility aids

lifestyle mobility aids B3600F Bedienungsanleitung

Moretti

Moretti MOPEDIA RS910 Bedienungsanleitung

Lumex

Lumex 89333 Bedienungsanleitung

aidapt

aidapt Solo VY397A Handbuch