Invacare Tracer SX5 Recliner Gebrauchsanweisung

Part No. 1110194 Rev A 1Tracer® SX5 Recliner Conversion Kit

Tracer® SX5 Recliner Conversion Kit

Assembly and Installation Instructions

SAVE THESE INSTRUCTIONS

NOTE: Check ALL parts for shipping damage. In case of shipping damage, DO NOT use. contact

Carrier/Dea er for further instruction.

SAFETY SUMMARY

To ensure the safe installation of the Recliner Conversion Kit, these instructions

MUST be followed:

WARNING

O NOT install or use this equipment without first reading and understanding

these instructions and the Owners Manual, part number 1110550. If you are

unable to understand the Warnings, Cautions or Instructions, contact a

healthcare professional, dealer or technical personnel before attempting to

install this equipment - otherwise, injury or damage may occur.

AFTER conversion of the wheelchair and BEFORE USE of the recliner, read

the GENERAL GUI ELINES and RECLINER sections of the Owners Manual,

part number 1110550, for recliner operation instructions.

INSTALLATION WARNING

After ANY adjustments, repair or service and before use, make sure all attaching

hardware is tightened securely - otherwise injury or damage may occur.

SX5 Recliners MUST have 8-inch casters installed. If the wheelchair originally

had 6-inch casters installed, seat-to-floor height adjustments MUST be made.

Seat-to-floor adjustments will also be necessary for certain 8-inch caster

mounting positions. Refer to the SEAT-TO-FLOOR section in the Owners

Manual, part number 1110550, for these adjustments.

SX5 Recliners CANNOT be used with the following options/accessories: one-

arm drive, solid folding seat, IV/O2 holder, O2 holder, Model 2218 IV rod,

amputee attachments or quick release axles. These options/accessories

MUST be removed prior to the conversion of the wheelchair.

SX5 Recliners MUST have properly installed and adjusted wheel locks and

anti-tippers. Refer to INSTALLING/A JUSTING THE WHEEL LOCKS

and INSTALLING THE ANTI-TIPPERS in this instruction sheet. Failure to

observe this warning can result in serious injury.

Tracer® SX5 Recliner Conversion Kit 2Part No. 1110194 Rev A

REMOVING EXISTING WHEELCHAIR COMPONENTS

To convert the wheelchair to a recliner, the following components MUST be removed:

Rear Wheels

Arms

Back anes

Back Upholstery

Wheel Locks

Fork/ aster Assemblies - if wheelchair is 14 to 18-inches wide.

REMOVING THE REAR WHEELS

Refer to REMOVING/INSTALLING THE REAR WHEELS in the Owners Manual, part

number 1110550.

This kit contains the following items:

DESCRIPTION QUANTITY DESCRIPTION QUANTITY

Back Assembly 1 Wheel Lock Shoe Extension 2

Headrest Assembly 1 Quad Release 2

Headrest Pillo 1 Spring Button Assembly 2

Fork Assembly ith Caster 2* Armrest Plug 2

Washers (Fork Stem) 2* Rear Arm Socket ith Hard are 2

Pivot Bushing 2 Anti-Tipper 2

Offset Wheel Bracket (Left) 1 Cap Nut 4

Offset Wheel Bracket (Right) 1 Flat Head Socket Scre 2

U-Bracket 2 Offset U-bracket Mounting Scre 2

SX5 O ners Manual 1

*NOTE: These items are not inc uded in kits for 20 and 22-inch wide (300 b. weight capacity)

whee chairs. These whee chairs are shipped from the factory with the required fork, fork hardware,

and casters a ready insta ed. Refer to the FRONT CASTER section of the Owners Manua , part

number 1110550, for more information.

Part No. 1110194 Rev A 3Tracer® SX5 Recliner Conversion Kit

Back Cane

Wheelchair Frame

Locknut

FIGURE 1 - REMOVING THE BACK CANES

Hex Screw

OUTSI E OF

WHEELCHAIR

INSI E OF

WHEELCHAIR

REMOVING THE WHEEL LOCKS (FIGURE 2)

1. Ensure the wheel lock is in the open (unlocked) position.

2. Remove the bolt and locknut that secure the wheel lock assembly to the wheelchair

frame.

3. Repeat STEPS 1-2 for the opposite wheel lock.

Bolt and

Locknut

FIGURE 2 - REMOVING THE WHEEL LOCKS

Wheel Lock

Rear Upright

REMOVING THE FLIP BACK ARMS

Refer to USING OR REPLA ING FLIP-BA K ARMREST in the Owners Manual, part

number 1110550.

REMOVING THE BACK CANES (FIGURE 1)

1. Remove the locknut from the bottom of each back cane.

2. Unthread the hex screw from the bottom of each back cane.

3. Remove the back canes with the upholstery from the wheelchair frame.

Tracer® SX5 Recliner Conversion Kit 4Part No. 1110194 Rev A

INSTALLING THE RECLINING BACK

1. Remove the components listed in REMOVING EXISTING WHEEL HAIR

OMPONENTS in this instruction sheet.

2. Perform the following to complete installation of the reclining back:

Install the Rear Arm Sockets

Install the Offset Wheel Brackets

Install the Reclining Back Assembly

Install the Rear Wheels

Install/Adjust the Fork/ aster Assemblies

Install the Wheel Locks

onvert Flip Back Arms to Removable Arms

Install the Spreader Bar

Install the Rear Anti-tippers

Install the Headrest and Pillow

REMOVING THE FORK/CASTER ASSEMBLIES - WHEELCHAIRS

UNDER 20-INCHES WIDE ONLY (FIGURE 3)

1. Remove the dust cover.

2. Remove the locknut and nylon washer that secures the fork to the caster headtube.

3. Drop the front caster and fork out of the caster headtube.

4. Repeat STEPS 1-3 for the opposite fork/caster assembly.

Locknut

Dust Cover

Fork Caster

Assembly

Nylon Washer

Caster Headtube

FIGURE 3 - REMOVING THE FORK/CASTER ASSEMBLIES -

WHEELCHAIRS UN ER 20-INCHES WI E ONLY

Part No. 1110194 Rev A 5Tracer® SX5 Recliner Conversion Kit

OUTSI E OF

WHEELCHAIR

FRAME

ETAIL A - ARM SOCKET

FIGURE 4 - INSTALLING THE REAR ARM SOCKET

Hole

Locknut

Arm

Socket

Armrest Mounting

Bracket

Wheelchair

Frame

REAR OF

WHEELCHAIR

INSTALLING THE OFFSET WHEEL BRACKETS (FIGURE )

NOTE: Stand behind the whee chair to determine right and eft sides.

1. Examine the rear of the offset wheel brackets (DETAIL B).

A. RIGHT AXLE LUG LONGER = RIGHT offset wheel bracket

B. LEFT AXLE LUG LONGER = LEFT offset wheel bracket.

2. Slide the bottom tube of the RIGHT offset wheel bracket over the RIGHT lower frame

tube.

3. Ensure the clevis sits flush against the rear upright.

4. Position the U-bracket so the countersunk hole faces towards the outside of the

wheelchair frame.

5. Insert the U-bracket tube into the rear upright.

6. Align the mounting hole in the U-bracket tube with the mounting hole in the rear upright

and clevis.

7. Install the hex screw through the clevis, rear upright tube and U-bracket tube from the

outside of the wheelchair frame.

8. Secure the offset rear wheel bracket to the wheelchair frame with a locknut. Torque to

165-175 in./lbs.

9. Repeat STEPS 1-8 on the left side of the wheelchair using the left offset wheel bracket.

NOTE: Right arm socket shown.

INSTALLING THE REAR ARM SOCKETS (FIGURE 4)

1. Position one (1) arm socket on the outside of the wheelchair frame, as shown in

FIGURE 4.

NOTE: There are right and eft versions of the arm socket. The ho e in the arm socket (DETAIL A)

shou d be facing the REAR whee chair when mounted.

2. Secure the arm socket to the armrest mounting bracket with the locknut. Torque to

30-40 in. lbs.

3. Repeat STEPS 1-2 for the opposite arm socket.

Tracer® SX5 Recliner Conversion Kit 6Part No. 1110194 Rev A

INSTALLING THE RECLINING BACK ASSEMBLY (FIGURE 6)

NOTE: This procedure requires two (2) peop e. One (1) person is needed to support the rec ining

back assemb y during the procedure.

NOTE: Stand behind the whee chair to determine right and eft sides.

NOTE: Ensure the rec ining mechanism cab es (not shown) are positioned towards the inside of

the whee chair frame.

1. Install the spacer into the pivot bushing at the bottom of the right back cane.

2. Position the pivot bushing with spacer into the right U-bracket .

3. Install a flat head socket screw through the right U-bracket, spacer and pivot

bushing.

4. Install a cap nut onto the flat head socket screw. Torque to 120 in./lbs.

5. Align the mounting hole at the bottom of the right reclining back tube with the top

clevis on the right offset wheel bracket.

6. Install a hex screw through the top clevis and reclining back tube.

7. Install a cap nut onto the hex screw. Tighten the nut just enough to remove the side

play of the reclining back tube with the clevis.

NOTE: DO NOT overtighten the cap nut. Otherwise the rec ining back wi be difficu t to operate.

8. Repeat STEPS 1-7 for the left side of the reclining back assembly.

Hex Screw

Locknut

U-Bracket

Tube

Clevis

Right Offset

Wheel Bracket

Mounting Hole

Wheelchair

Frame

OUTSI E OF

WHEELCHAIR

FRAME

Countersunk Hole

Rear Upright

FIGURE 5 - INSTALLING THE OFFSET WHEEL BRACKETS

ETAIL B - REAR VIEW

LEFT OFFSET

WHEEL BRACKET

RIGHT OFFSET

WHEEL BRACKET

Longer

Axle Lug

Longer

Axle

Lug

Mounting Hole

NOTE: Arm socket and mounting bracket not

shown for c arity

NOTE: On y RIGHT side of whee chair shown

for c arity. Left side insta s in a simi ar manner.

Part No. 1110194 Rev A 7Tracer® SX5 Recliner Conversion Kit

INSTALLING THE REAR WHEELS

Refer to REMOVING/INSTALLING THE REAR WHEELS in the Owners Manual, part

number 1110550.

INSTALLING/ADJUSTING THE FORK/CASTER ASSEMBLIES

WARNING

SX5 Recliners MUST have 8-inch casters installed. If the wheelchair originally

had 6-inch casters installed, seat-to-floor height adjustments MUST be made.

Seat-to-floor adjustments will also be necessary for certain 8-inch caster

mounting positions. Refer to the SEAT-TO-FLOOR section in the Owners

Manual, part number 1110550, for these adjustments.

Wheelchairs Under 20-inches Wide ONLY.

Install 8-inch forks/caster assemblies.Refer to INSTALLING/REPLA ING FORK

ASSEMBLIES in the Owners Manual, part number 1110550.

All Wheelchair Widths.

heck that the front casters have been mounted properly for the rear wheel size. Refer to

the SEAT-TO-FLOOR section in the owners manual, part number 1110550.

Reclining Back

Assembly

Wheelchair

Frame

Right Back Cane

Spacer

Pivot Bushing

Right U-Bracket

Cap Nut

Flat Head

Socket Screw

Hex Screw

Cap Nut

Right

Reclining

Back

Tube

Top Clevis

Mounting Hole

Right Offset

Wheel Bracket

FIGURE 6 - INSTALLING THE RECLINING BACK ASSEMBLY

NOTE: Arm socket and back upho stery

not shown for c arity.

NOTE: On y RIGHT side of whee chair shown

for c arity. Left side insta s in a simi ar manner.

Tracer® SX5 Recliner Conversion Kit 8Part No. 1110194 Rev A

Installing the Wheel Lock Shoe xtension (FIGUR 8).

1. If necessary, disengage the wheel lock.

2. Loosen the two (2) set screws in the wheel lock shoe extension.

3. Insert the wheel lock shoe into the slot in the wheel lock shoe extension.

NOTE: Ensure the pointed end of the whee ock shoe extension is facing toward the rear whee .

4. Position the wheel lock shoe extension so it is flush with the end of the wheel lock

shoe.

5. Tighten the two (2) set screws to secure the wheel lock shoe extension to the

wheel lock shoe.

6. Repeat STEPS 1-5 for the opposite side of the wheelchair.

7. Adjust the wheel locks. Refer to ADJUSTING THE WHEEL LO KS in this

procedure of the instruction sheet.

FIGURE 7 - INSTALLING THE BOLT-ON WHEEL LOCKS

Bolt and Locknut

Wheel

Lock

Slot Wheelchair Frame

INSTALLING/ADJUSTING THE WHEEL LOCKS

NOTE: If the whee chair has 24-inch rear whee s, bo t-on whee ocks must be used with the whee ock

shoe extension provided in this kit.

NOTE: If the whee chair has 20 or 22-inch rear whee s, c amp-on whee ocks must be used. Contact

Invacare for ordering information.

Installing Bolt-On Wheel Locks (FIGUR 7).

1. Align the slot in the wheel lock with the rear wheel lock mounting hole in the

wheelchair frame.

2. Install the bolt through the wheel lock and the wheelchair frame.

3. Loosely install a locknut onto the bolt.

4. Repeat STEPS 1-3 for the opposite side of the wheelchair.

5. Install the wheel lock shoe extension. Refer to INSTALLING THE WHEEL LO K

SHOE EXTENSION in this procedure of the instruction sheet.

Part No. 1110194 Rev A 9Tracer® SX5 Recliner Conversion Kit

ADJUSTING THE WHEEL LOCKS (FIGURE 10)

NOTE: If whees are pneumatic, before adjusting or repacing the whee ock assembies, ensure that the tires are

infated to the recommended psi on the side wa of tire. The recommended tire pressure is ocated on the side wa

of the tire.

1. Disengage the wheel locks.

2. Loosen the bolt and locknut that secure the wheel lock to the wheelchair frame.

3. Reposition the wheel lock so that when engaged, the wheel lock shoe embeds the tire 1/8-inch

(3/16-inch for pneumatic tires) and HOL S the occupied wheelchair in place when pushed.

4. Securely tighten the bolt and locknut securing the wheel lock to the wheelchair frame.

5. Engage the wheel lock.

FIGURE 8 - INSTALLING WHEEL LOCK SHOE EXTENSION

Slot

Set Screws

Pointed End of

Wheel Lock

Shoe Extension

Wheel Lock

Shoe

Extension

Wheel Lock

Wheel Lock Shoe Extension

Rear Wheel

FIGURE 9 - INSTALLING CLAMP-ON WHEEL LOCKS

Bolt

Locknut

Wheel Lock Shoe

Wheelchair Frame

Installing Clamp-On Wheel Locks (FIGUR 9).

1. Position the clamp onto the wheelchair frame.

2. Adjust the clamp position so the wheel lock shoe will embed the tire when engaged.

NOTE: Any whee ock adjustment shou d embed the whee ock shoe at east 1/8-inch (3/16-inch

if pneumatic tire) into the tire when engaged.

3. Loosely install the bolt and locknut.

NOTE: It may be necessary to squeeze the c amp together with p iers to insta the bo t.

4. Repeat STEPS 1-2 for the opposite side of the wheelchair.

5. Adjust the wheel locks. Refer to ADJUSTING THE WHEEL LO KS in this

procedure of the instruction sheet.

NOTE: Right

side shown.

Tracer® SX5 Recliner Conversion Kit 10 Part No. 1110194 Rev A

CONVERTING ARMS FROM FLIP-BACK STYLE TO

REMOVABLE STYLE (FIGURE 11)

1. Remove the insert from the bottom of the rear arm tube.

2. Align the spring buttons with the spring button holes in the rear arm tube.

3. Install spring button assembly into rear arm tube until both spring buttons protrude

from the spring button holes.

4. Press and hold spring button in.

5. Slide the release lever up and over the top snap button.

NOTE: Orient the ever so that it rotates to the outside of the whee chair to retract the spring

buttons.

5. Position the plug button so the arrow on the bottom points towards the spring

button holes in the rear arm tube.

FIGURE 10 - A JUSTING THE WHEEL LOCKS

Wheel

Lock

Handle

Bolt and Locknut

Wheel Lock

Shoe

Rear

Wheel

Lock

BOLT-ON WHEEL LOCKS CLAMP-ON WHEEL LOCKS

ETAIL "C" - WHEEL LOCK SHOE

ENGAGEMENT

1 8-inch (3 16-inch

pneumatic tires)

Tire

Wheel Lock

Shoe

Wheel Lock

Shoe

Rear Wheel

Wheelchair

Frame

6. Measure the distance the wheel lock is embedded into the tire as shown in DETAIL " " of

FIGURE 10.

NOTE: Any whee ock adjustment shoud embed the whee ock shoe at east 1/8-inch (3/16-inch if pneumatic tire)

into the tire when engaged.

7. Repeat STEPS 1-6 until the wheel lock shoe embeds the tire 1/8-inch (3/16-inch for pneumatic

tires) and HOL S the occupied wheelchair in place when pushed. If the correct measurement

still cannot be achieved, contact a qualified technician.

8. Repeat STEPS 1-7 for the opposite wheel lock.

Andere Handbücher für Tracer SX5 Recliner

Andere Invacare Mobilitätshilfe Handbücher

Invacare

Invacare Dolomite Brass Bedienungsanleitung

Invacare

Invacare Dolomite Maxi+ Bedienungsanleitung

Invacare

Invacare SEAT RIGIDIZER Montageanleitung

Invacare

Invacare Dolomite Step Up Bedienungsanleitung

Invacare

Invacare CTMT-F Bedienungsanleitung

Invacare

Invacare Spartan 65400 Montageanleitung

Invacare

Invacare Futura/Symphony Bedienungsanleitung

Invacare

Invacare H140 Bedienungsanleitung

Invacare

Invacare Aquatec 90000 Bedienungsanleitung

Invacare

Invacare Dolomite Gloss Bedienungsanleitung

Invacare

Invacare Spartan 65420 Bedienungsanleitung

Invacare

Invacare 6291E Junior Montageanleitung

Invacare

Invacare Asteria P409 Bedienungsanleitung

Invacare

Invacare 2218 Montageanleitung

Invacare

Invacare 1073913 Montageanleitung

Invacare

Invacare ROZE Bedienungsanleitung

Invacare

Invacare OCMK01 Montageanleitung

Invacare

Invacare Dolomite Jazz 510 Bedienungsanleitung

Invacare

Invacare FR300 Montageanleitung

Invacare

Invacare Birdie Bedienungsanleitung

Invacare

Invacare H335 Bedienungsanleitung

Invacare

Invacare Formula Bedienungsanleitung

Invacare

Invacare RHL450-1 Montageanleitung

Invacare

Invacare Rollator Bedienungsanleitung

Beliebte Mobilitätshilfe Handbücher anderer Marken

Alber

Alber Scalamobil iQ Bedienungsanleitung

Ferno

Ferno CCT-PX Bedienungsanleitung

Otto Bock

Otto Bock Pheon 3R62 Bedienungsanleitung

NRS Healthcare

NRS Healthcare M11090 Bedienungsanleitung

Medline

Medline MDS86835DSHEC Installationsanleitung

HEPRO

HEPRO Gripo Bedienungsanleitung

Guldmann

Guldmann Twin Turner II Bedienungsanleitung

Drive

Drive ROOMBA Bedienungsanleitung

Gate

Gate Balder Bedienungsanleitung

Decon wheel

Decon wheel TNS Notos Bedienungsanleitung

ExoAtlet

ExoAtlet ExoAtlet-II Bedienungsanleitung

Rhythm Healthcare

Rhythm Healthcare B3800F Bedienungsanleitung

AMF-BRUNS

AMF-BRUNS PROTEKTOR Bedienungsanleitung

Drive DeVilbiss Healthcare

Drive DeVilbiss Healthcare OTTER Bedienungsanleitung

Rhythm Healthcare

Rhythm Healthcare C500U Bedienungsanleitung

Lumex

Lumex RJ4200A Bedienungsanleitung

Rebotec

Rebotec Jumbo Bedienungsanleitung

Rehaforum MEDICAL

Rehaforum MEDICAL PR50548 Bedienungsanleitung