IOptron CEM26 Bedienungsanleitung

Instruction on Polar Scope Replacement of a CEM26/GEM28 Mount

Toll needed: a set of metric Allen wrench

DO NOT OVER TIGHTEN THE SET SCREW!!!

To Remove/Replace/Rotate a CEM26/GEM28 iPolar:

For GEM28

1. Unthread the red RA rear cover

2. Release two set screws on RA axle.

3. Pull out the iPolar

4. Set the mount in Zero Position and insert a New iPolar

5. Check the iPolar orientation to make sure ALT adjustment will result image vertical movement.

For CEM26

1. Release the screws from side

2. Release the other screw from the bottom

3. Pull out the iPoler

4. Set the mount in Zero Position and insert a New iPolar.

5. Check the iPolar orientation to make sure ALT adjustment will result image vertical movement.

To Install an AccuAlignTM Optical Polar Scope:

The RA axis locking wrench will not be able to be used due to the length of optical polar scope.

The LED brightness is not adjustable. You’ll need to block part of the LED if you would like a dim illumination.

1. Set the mount at Zero Position

2. Insert the optical polar scope. Set any one of major marks on top to assume the 12 o’clock position.

3. Tighten the set screws

4. Thread in the polar scope LED. Plug the 3mm DC plug into the LED and 5.5mm plug into DC 12V OUT socket on

main board.

5. Turn on the mount power to check the LED and polar scope.

Major mark

Polar Scope Alignment

There are three Reticle Adjustment Screws on the side of the Polar scope, as shown in the following photo.

(1) Aim the polar scope to a distant object, such as a flag top or building corner. Adjust the object lens to focus the polar

scope to the object. Adjust the eyepiece to see the dial clearly. Center the object in polar scope by adjusting mount

altitude and azimuth adjustment screws.

(2)Bring the object half the distance to the center by adjusting the reticle adjustment screws. Loose one screw first,

then tighten the other screw(s). Only loose/tighten one screw at a time and very small amount of turn each time to

avoid the reticle totally lost its position. It may take a few minutes to familiarize yourself with the screws that move the

polar scope in the appropriate direction. PLEASE do not over tighten the setting screws. The reticle is made from a

glass.

(3) Rotate the mount 180 degree to bring the mount back to the left side. If you are lucky enough, the object will stay in

center of the polar scope. Otherwise, repeat Step 1 to further move the object to the center. After few times, the object

will stay in center when the mount is flipped from right to left.

Rotate

Center the object

Bring the object

half the distance

to the center

Rotate

Center the object

Bring the object

half the distance

to the center

Reticle Adj. Screws

Objective Lens

Lock Ring

Andere Handbücher für CEM26

Dieses Handbuch passt für folgende Modelle

Andere iOptron Rack & Stand Handbücher

iOptron

iOptron SkyHunter Portable EQ/AZ GoTo System Bedienungsanleitung

iOptron

iOptron HAE69B Bedienungsanleitung

iOptron

iOptron C70A Series Bedienungsanleitung

iOptron

iOptron Precision AZ/EQ Base Bedienungsanleitung

iOptron

iOptron MiniPier Bedienungsanleitung

iOptron

iOptron CEM40G Bedienungsanleitung

iOptron

iOptron CEM120 Bedienungsanleitung

iOptron

iOptron CEM25 Bedienungsanleitung

iOptron

iOptron GEM45 Bedienungsanleitung

iOptron

iOptron GEM45EC Bedienungsanleitung

iOptron

iOptron CEM120 Bedienungsanleitung

iOptron

iOptron GEM28 Bedienungsanleitung

iOptron

iOptron HEM27 Bedienungsanleitung

iOptron

iOptron HEM27 Bedienungsanleitung

iOptron

iOptron iEQ30 Pro 3000E Bedienungsanleitung

iOptron

iOptron CEM120 7300 Bedienungsanleitung

iOptron

iOptron MiniTower GOTO Bedienungsanleitung

iOptron

iOptron CEM40EC Bedienungsanleitung

iOptron

iOptron GEM45 Bedienungsanleitung

iOptron

iOptron SkyGuide 3550A Bedienungsanleitung

iOptron

iOptron CEM40 Bedienungsanleitung

iOptron

iOptron SmartStar CubePro GOTO AltAz Bedienungsanleitung

iOptron

iOptron HAE29 Bedienungsanleitung

iOptron

iOptron SmartStar MiniTower Pro Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung

iOptron CEM26 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken